Einhell 44.651.60 Cordless Multifunction Tool Instruction Manual

Einhell 44.651.60 Cordless Multifunction Tool

Danger!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the in-formation is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents that arise due to a failure to follow these instructions and the safety instructions.

Explanation of the symbols used (see Fig. 10)

1. Danger! – Read the operating instructions to reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noise can cause hearing damage.
3. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!
4. Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
5. Store the batteries only in dry rooms with an ambient temperature of +10°C to +40°C. Place only fully charged batteries in storage (charged at least 40%).

Safety regulations

The corresponding safety information can be found in the enclosed booklet.

Warning!
Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re, and/or serious injury. Keep all the safety information and instruc-tions in a safe place for future use.

Layout and items supplied

Layout (Fig. 1)

1. On/Off switch
2. Tool chuck
3. Charger (in the case of Art. No.: 44.651.60 it is not included in delivery)
4. Speed controller
5. Quick-release lock for changing tools
6. Battery pack (in the case of Art. No.: 44.651.60 it is not included in delivery)
7. Pushlock button
8. Scraper
9. Triangular grinding/sanding plate
10. Plunge-cut saw blade for wood
11. Plunge-cut saw blade for metal
12. Segmented saw blade
13. Abrasive paper
14. Disk

Items supplied
Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. There is a danger of swallowing or suff ocating!

• Multifunction tool
• Triangular grinding/sanding plate
• Scraper
• 9x abrasive paper
• Plunge-cut saw blade for wood
• Plunge-cut saw blade for metal
• Segmented saw blade
• Original operating instructions
• Safety instructions

Proper use

The equipment is suitable for sanding/grinding small areas. For sanding/grinding larger areas the vacuum extractor, which is available as an accessory (see 7.3), must be used. The equipment is designed for the sanding/grinding of wood, iron, plastic and similar materials using the appropriate abrasive paper. Furthermore, the equipment is intended for sawing wood, plastic, and similar materials, as well as scraping off glued carpets, filling compound residues, old paint and similar applications. The equipment is to be used only for its prescri-bed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or inju-ries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

• Motor power supply : …………………………. 18 V DC
• Idling speed : ………………………11000-20000 min-1
• Sanding/grinding area : …………. 90 x 90 x 90 mm
• Oscillation angle : …………………………………….3.2°
• Weight : ……………………………………………….1.0 kg

Important!
The equipment is supplied without rechargeable batteries and without a charger and is allowed to be used only with the lithium-ion batteries of the Power-X-Change series! The lithium-ion batteries of the Power-X-Change series are allowed to be charged only with Power- X chargers.

Danger! Sound and vibration Sound and vibration values were measured under EN 62841.

• LpA sound pressure level …………………… 78 dB(A)
• KpA uncertainty ………………………………………3 dB
• LWA sound power level …………………….. 89 dB(A)
• KWA uncertainty ………………………………………3 dB

Wear ear-muffs.
The impact of noise can cause damage to hearing. Total vibration values (vector sum of three directions) determined in accordance with EN 62841.

Handle

• Vibration emission value ah = 13.9 m/s2
• K uncertainty = 1.5 m/s2

The stated vibration emission levels and stated noise emission values were measured by a set of standardized criteria and can be used to compare one power tool with another. The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure.

Warning
The vibration and noise emission levels may vary from the level specifi ed during actual use, depending on how the power tool is used, especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances that are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Caution! Residual risks
Even if you use this electric power tool by instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage is caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Before using the equipment

Warning!
Always remove the battery pack before making adjustments to the equipment. Be sure to read the following information before you put the cordless equipment into operation:

• Charge the battery pack with the charger.

Fitting the plug-in tools (Figures 1-5)

• Open the quick-release lock for changing tools (5) as shown in Fig. 2.
• To fit the plug-in tools safely you should hold the multifunction tool so that the On/Off switch (1) points down and the tool chuck (2) faces up.
• Place the plug-in tool (e.g. the scraper) on the tool chuck (2) so that the pins of the tool chuck fit into the recesses in the plug-in tool. The tool chuck (2) is magnetic to secure the plug-in tool during the clamping procedure.
• Close the quick-release lock for changing tools (5) again. Take care that the pins of the chuck (2) remain in the recesses in the plugin tool.
• The equipment comes with a disk (14) for safely securing plug-in tools with recesses. Please note the correct use (camber facing the tool) of the disk (14) for plug-in tools with recess as shown in Fig. 4 and 5. Be sure to read the following information before you put the cordless equipment into operation:

Check that the plug-in tool is secure.

Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the equipment as a delta sander/grinder.

Fastening the sanding/grinding paper
The hook-and-loop-fastener enables easy changing of the abrasive paper. Make sure that the vacuum extraction holes on the abrasive paper and the grinding/sanding disk are aligned.

Operation

Charging the LI battery pack (Fig. 6/7)

1. Remove the battery pack (6) from the handle, pressing the push lock button (7) downwards to do so.
2. Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger into the socket outlet. The green LED will then begin to fl ash.
3. Push the battery pack onto the battery char-ger.

In section 10 (Charger indicator) you will fi nd a table with an explanation of the LED indicator on the charger. If the battery pack fails to charge, check for the following:

• voltage at the power socket
• whether there is good contact at the charging contacts of the charging unit If the battery pack still fails to charge, send
• the charging unit
• and the battery pack to our customer service center.

To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased. When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fi res. To ensure that the battery pack provides long service, you should take care to recharge it promptly. You must recharge the battery pack when you notice that the performance of the device drops. Never allow the battery pack to become fully discharged. This will cause it to develop a defect.

Switching on and off (Fig. 8)

• Slide the switch (1) forwards to switch on the equipment.
• Slide the switch (1) to the rear again to switch off the equipment.

Practical tips

• Switch on the equipment.
• Work away from the body.
• Never move your hands into the direct vicinity of the work area.
• Use only plug-in tools that are in good working order and undamaged.

Plug-in tools:

• Sawing: Sawing wood and plastic.
• Notes on working practice : When sawing, watch out for foreign bodies in the material and remove them if necessary. Plunge cutting is allowed only in soft materials such as wood or plasterboard.
• Sanding/grinding : Surface sanding/grinding at edges, in corners, or in hard-to-reach areas. Depending on the choice of abrasive paper for the sanding/grinding of wood, paint, lacquer, etc.

Notes on working practice:
This equipment offers particularly high performance for the grinding/sanding of hard-to-reach corners and edges. To grind/sand profi les and channels you can also work with just the tip or the edge of the grinding/sanding disk. Various grinding/sanding papers are available, specially designed for the different types of material you may be working on and the amount you wish to remove from the surface. The amount removed will depend largely on the choice of sanding/grinding paper and pressure applied to the sanding/grinding disk.

Scraping: Scraping off old paint or adhesives. Notes on working practice: Move the plug-in tool against the area you want to remove. Begin with a fl at an angle of incidence and little pressure. The surface (e.g. wood, plaster) may be damaged if too much pressure is used.

Speed control (Fig. 8)
You can select the speed by turning the speed controller (4).

• Plus direction : Higher speed
• Minus direction : Lower speed

Battery capacity indicator (Fig. 9 /Item b)
Press the battery capacity indicator switch (a). The battery capacity indicator (b) will indicate the charge status of the battery by means of 3 LEDs.

All 3 LEDs are lit:
The battery is fully charged.

2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED flashes:
The battery is empty, recharge the battery.

All LEDs blink:
The battery temperature is too low. Remove the battery from the equipment, keep it at room tem-perature for one day. If the fault reoccurs, this me-ans that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.

Cleaning, maintenance and ordering spare parts

Hazard!
Always take the battery out of the equipment be-fore starting any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could atattackhe plastic parts of the equipment. EEnsurethat no water can seep into the device. Water ingress into an electric tool increases the risk of an electric shock.

Maintenance
There are no parts inside the equipment that require additional maintenance.

Ordering spare parts and accessories
Please provide the following information when ordering spare parts:

• Type of unit
• Article number of the unit
• ID number of the unit
• Spare part number of the required spare part For our latest prices and information please go to www.Einhell-Service.com

Tip! For good results, we recommend high-quality accessories! www.kwb.eu welcome@kwb.eu

• Dust extraction adapter (Art. No.: 44.651.63)

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask your local council offices.

Storage

Store the equipment and accessories in a dark and dry place at above-freezing temperature. The ideal storage temperature is between 5 and 30°C. Store the electric tool in its original packaging.

Charger indicator

Disposal

Power tools, rechargeable batteries, accessories, and packaging should be sorted for environmental recycling. Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/ EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner. If disposed of incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for the United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of Einhell Germany AG. Subject to technical changes

Service Information

We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

• Not necessarily included in the scope of delivery! In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:
• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) before the failure?
• What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.

Warranty certificate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of the guarantee are not aff ected by this guarantee. Our guarantee is free of charge to you.
2. The guarantee services cover only defects due to material or manufacturing faults on the new product that you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectifi cation of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name “Professional” has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.
3. Our guarantee does not cover:
   • Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
   • Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand,  stones, dust, ….) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).
   • Damage to the equipment or parts of the equipment which is owed to use-related, normal, or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design-related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration, and impact.
   • The guarantee is valid for 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fi tted. This also applies if on-site service is used.
   • To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and retur-ned to you or we will send you a new replacement.
   • If you have taken the equipment with you to a different EU country than where you bought it, we will arran-ge for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.

Of course, we are also happy to offer a chargeable repair service for any defects which are not covered or no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning worn parts, consumables, and missing parts as presented in the service information included in this operating manual.

Warrantor/ Service:
Einhell UK Ltd, Unit 10, 1st Floor, Champion‘s Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0UQ

• Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article

*Akku-Multifunktionswerkzeug VARRITO (Einhell)**

• 2014/29/EU
• 2005/32/EC_2009/125/EC
• (EU)2015/1188
• 2014/35/EU
• 2006/28/EC
• X 2014/30/EU
• 2014/32/EU
• 2014/53/EU
• 2014/68/EU
• (EU)2016/426

Notified Body:

• (EU)2016/425
• X 2011/65/EU_(EU)2015/863
• X 2006/42/EC
• Annex IV
• Notified Body:
• Reg. No.:
• 2000/14/EC_2005/88/EC
• Annex V
• Annex VI
• Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = kW; L/Ø = cm
• Notified Body:
• 2012/46/EU_(EU)2016/1628
• Emission No.:

Standard references: EN 62841-1; EN 62841-2-4; EN 55014-1; EN 55014-2

• Cordless Multifunction Tool ·

Declaration of conformity

We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for:

Cordless Multifunctional Tool VARRITO (Einhell)

UK Legislation

• Simple Pressure Vessels (Safety) Regulation
• Electrical Equipment (Safety) Regulation
• Radio Equipment Regulation
• Electromagnetic Compatibility Regulation
• Measuring Instruments Regulation
• Pressure Equipment (Safety) Regulation
• Personal Protective Equipment Regulation
• The Ecodesign for Energy-Related Products and Energy Information Regulation
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation
• Noise Emission in the Environment by Equipment for use Outdoors Regulation
• Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
• Supply of Machinery (Safety) Regulation
• Annex IV Notifi ed Body: Reg. No.:

Standards: BS EN 62841-1; BS EN 62841-2-4; BS EN 55014-1; BS EN 55014-2;

References

• Einhell Service
• service.com is for sale | www.brandforce.com
• VICE - VICE is the definitive guide to enlightening information.
• Einhell Service
• Herramientas de alta calidad para aficionados al bricolaje y la jardinería | Einhell.es
• Strumenti di alta qualità per gli amanti del Fai da Te e del giardinaggio | Einhell.it
• kwb Germany GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>