FDLR18-1 Ventless Dual Fuel Gas Log Set

“`html

Product Information

Specifications

• Model: FDLR18-1

• Type: Dual Fuel Yellow Flame Remote Vent-Free Gas Log
  Chassis

• Gas Type: Natural Gas or Propane

• Patents: Covered by multiple US patents

Product Features

The Dual Fuel Yellow Flame Remote Model FDLR18-1 is a vent-free
gas log chassis designed to operate with natural gas or propane. It
is equipped with a remote control for convenient operation and
features a yellow flame for a realistic fire effect.

Product Identification

This appliance is identified by model number FDLR18-1 and is
suitable for use in aftermarket, permanently located, manufactured
homes where not prohibited by local codes. It is important to
ensure proper combustion and ventilation air supply when installing
this unit.

Qualified Installing Agency

Installation and service of this appliance should only be
performed by a qualified installer, service agency, or the gas
supplier. Improper installation or maintenance can lead to property
damage or personal injury.

Local Codes

Ensure compliance with local codes and regulations when
installing the Dual Fuel Yellow Flame Remote Model FDLR18-1.
Failure to do so may result in safety hazards and void the
warranty.

Product Usage Instructions

Installation

1. Before installation, ensure proper ventilation and combustion
air supply as per the guidelines provided in the manual.

2. Follow the detailed installation instructions outlined in the
manual to securely set up the gas log chassis.

3. If unsure about any step, consult a qualified installer or
service agency for assistance.

Operation

1. Use the included remote control to turn the appliance on/off
and adjust flame settings as desired.

2. Follow the operational procedures specified in the manual for
safe and efficient use of the gas log chassis.

3. Do not attempt to modify or alter the appliance in any way
that is not recommended by the manufacturer.

Maintenance

1. Regularly inspect and clean the gas log chassis to ensure
proper functioning and safety.

2. Schedule annual maintenance checks by a qualified
professional to keep the appliance in optimal condition.

Safety Precautions

1. Keep flammable materials away from the appliance to prevent
fire hazards.

2. In case of any issues or malfunctions, contact customer
service or a qualified technician for assistance.

FAQ

Q: Can this appliance be used with both natural gas and

propane?

A: Yes, the Dual Fuel Yellow Flame Remote Model FDLR18-1 is
equipped to operate with both natural gas and propane. Field
conversion between these gases is not permitted.

Q: What should I do if I encounter problems with the

appliance?

A: If you experience any issues, have questions, or require
assistance, contact our customer service department at
1-855-607-6557 for support.

“`

DUAL FUEL YELLOW FLAME REMOTE MODEL
FDLR18-1
VENT-FREE GAS LOG CHASSIS
OWNER’S OPERATION AND INSTALLATION MANUAL
PFS ®
US
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS · Do not try to light any appliance. · Do not touch any electrical switch; do not use any phone in your building. · Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. · If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING: This appliance is equipped for natural and propane gas. Field conversion is not permitted other than between natural or propane gases.
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-855-607-6557, 8:00 am – 4:30 pm CST, Monday through Friday or email contact@factorybuysdirect.com

TABLE OF CONTENTS

Safety ……………………………………………….. 3
Specifications …………………………………….. 5 Product Features ………………………………… 5 Product Identification …………………………… 5 Qualified Installing Agency …………………… 6 Local Codes……………………………………….. 6 Unpacking………………………………………….. 6 Water Vapor: A By- Product Of
Unvented Room Heaters ………………… 6 Air For Combustion and Ventilation ……….. 7 Installation …………………………………………. 9

Operation…………………………………………. 19 Inspecting Burners…………………………….. 23 Care And Maintenance ………………………. 24 Troubleshooting………………………………… 25 Replacement Parts ……………………………. 29 Service Hints ……………………………………. 29 Technical Service………………………………. 29 Parts ……………………………………………….. 30 Accessories ……………………………………… 31

SAVE THIS BOOK
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.
This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to Air For Combustion and Ventilation section on page 7 of this manual.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency or the gas supplier.
This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with propane or natural gas. Field conversion by any other means including the use of a kit is not permitted.

• Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
  PATENT INFORMATION This product may be covered by one or more of the following United States patents: 9,829,195 9,423,123 9,441,833 9,518,732 9,752,779 9,416,977 8,764,436
  8,568,136 8,516,878 8,297,968 8,281,781 8,235,708 7,967,006 7,967,007 7,730,765 7,677,236 7,607,426 7,434,447

2

www.factorybuysdirect.com

200234-01C

SAFETY

WARNING: Do not attempt to access or change the setting of the fuel selection means. Access to and adjustment of the fuel selection means must only be performed by a qualified service person when connecting this appliance to a specified fuel supply at the time of installation. Change of the selector setting to other than the fuel type specified at the time of the installation could damage this appliance and render it inoperable. The installer shall replace the access cover before completing the installation and operating this appliance.
IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock and carbon monoxide poisoning. Failure to follow these instructions will void the warranty.
Only a qualified installer, service agent, or local gas supplier may install and service this product.
WARNING: Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
WARNING: This appliance can be used with propane or natural gas. It is shipped from the factory adjusted for use with propane.

DANGER: Carbon monoxide poisoning may lead to death!
CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol and those at high altitudes.
NATURAL AND PROPANE GAS: Natural and propane gas are odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.
WARNING: FIRE, EXPLOSION AND ASPHYXIATION HAZARD Improper adjustment, alteration, service, maintenance, or installation of this heater or its controls can cause death or serious injury. Read and follow instructions and precautions in User’s Information Manual provided with this heater.
WARNING: Do not allow fans to blow directly into fireplace. Avoid any drafts that alter burner flame patterns.
WARNING: Do not use a blower insert, heat exchange insert or other accessory not approved for use with this heater.
WARNING: Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

200234-01C

www.factorybuysdirect.com

3

SAFETY

WARNING: Do not place clothing or other flammable material on or near the appliance. Never place any objects in the heater.
WARNING: The log set becomes very hot when running. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.
WARNING: Carefully supervise young children when they are in the room with the heater.
WARNING: You must operate this log set with fireplace screen in place.
WARNING: Use only logs approved for use with this burner system.
1. Do not place propane supply tank(s) inside any structure. Propane supply tank(s) must be placed outdoors.
2. This heater shall not be installed in a bedroom or bathroom.
3. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, pages 7 and 8. If heater keeps shutting off, see Troubleshooting, page 25.
4. Keep all air openings in front and bottom of heater clear and free of debris. This will ensure enough air for proper combustion.
5. If heater shuts off, do not relight until you have provided fresh, outside air. If heater keeps shutting off, have it serviced.
6. Do not run heater: · Where flammable liquids or vapors are used or stored. · Under dusty conditions.

7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.
8. Do not use heater if any part has been under water. Immediately call a qualified service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under water.
9. Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.
10. Operating heater above elevations of 4,500 feet could cause pilot outage.
11. To prevent performance problems, do not use propane fuel tank of less than 100 lbs. capacity.
12. Do not use this heater as a wood-burning heater.
13. Solid fuels should not be burned in fireplace in which a vent-free log set is installed. Do not use this heater to cook food or burn paper or other objects.
14. To prevent sooting, follow the instructions in Care and Maintenance (see page 24).
15. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of heater. After servicing, always replace fireplace screen before operating heater.
16. This heater is designed to be smokeless. If logs ever appear to smoke, turn off heater and call a qualified service person.
Note: During initial operation, slight smok-
ing could occur due to log curing and the
heater burning manufacturing residues.
17. If fireplace has glass doors, never operate this heater with glass doors closed. If you operate heater with doors closed, heat will build up inside fireplace and cause glass to burst. If fireplace opening has vents at the bottom, you must open the vents before operating log set. Always operate heater with glass doors fully open.
18. Do not use this heater if any log is broken. Do not operate heater if a log is chipped (dime-size or larger).

4

www.factorybuysdirect.com

200234-01C

SPECIFICATIONS

Model FDLR18-1 Ignition Electronic Piezo Ignitor

Gas Type Natural Gas Propane Gas

Maximum Input Rating 30,000 Btu/Hr 30,000 Btu/Hr

Manifold Pressure 4″ W.C.

9″ W.C.

Inlet Gas Pressure* Max. 9.5″ (inches of water) Min. 5″

Max. 14″ Min. 11″

*For purposes of input adjustment

PRODUCT FEATURES

This log set has been tested and approved to ANSI Z21.11.2 standard for Unvented Heaters and can be operated with the flue damper closed. State and local codes in some areas prohibit the use of vent-free heaters.
SAFETY PILOT
This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater is equipped with an electronic piezo control system. This system requires a AAA battery (provided).

THERMOSTAT HEAT CONTROL
When the hand held remote is in the THERMO mode, it automatically cycles the burner on and off to maintain a desired room temperature.
2 GAS OPTIONS AVAILABLE
Your heater is equipped to operate on either propane or natural gas. The heater is shipped from the factory ready for connecting to propane. The heater can easily be changed to Natural gas by having your qualified installer follow the instructions on page 13 and the markings on the heater.

PRODUCT IDENTIFICATION

Ignitor Button

Pilot Burner

200234-01C

Figure 1 – Vent-Free Log Chassis

Control Knob

www.factorybuysdirect.com

5

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code, ANSI Z223.1/NFPA 54.
Available from:
American National Standards Institute, Inc. 25 West 43rd Street New York, NY 10036
National Fire Protection Association, Inc. 1 Batterymarch Park
Quincy, MA 02269-9101
This heater is designed for vent-free operation. State and local codes in some areas prohibit the use of vent-free heaters.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.
Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.
In the State of Massachusetts the gas cock must be a T-handle type. The State of Massachusetts requires that a flexible appliance connector cannot exceed three feet in length.

UNPACKING

1. Remove burner base assembly from carton. Note: Do not pick up burner base assembly by burners as this could damage heater. Always handle base assembly by grate.

2. Remove all protective packaging applied to heater for shipment.
3. Check all items for any shipping damage. If damaged, promptly inform dealer where you purchased the heater.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30 mL) of water for every 1,000 BTUs (0.3 KWs) of gas input per hour. Unvented room heaters are recommended as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

The following steps will help ensure that water vapor does not become a problem.
1. Be sure the heater is sized properly for the application, including ample combustion air and circulation air.
2. If high humidity is experienced, a dehumidifier may be used to help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source.

QUALIFIED INSTALLING AGENCY

Only a qualified agency should install and replace gas piping, gas utilization equipment or accessories, and repair and equipment servicing. The term “qualified agency” means any individual, firm, corporation, or company that either in person or through a representative is engaged in and is responsible for:

a) Installing, testing, or replacing gas piping or
b) Connecting, installing, testing, repairing, or servicing equipment; that is experienced in such work; that is familiar with all precautions required; and that has complied with all the requirement of the authority having jurisdiction.

6

www.factorybuysdirect.com

200234-01C

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.
Today’s homes are built more energy efficient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible. While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation. Exhaust fans, fireplaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

WARNING: This heater shall not be installed in a room or space unless the required volume of indoor combustion air is provided by the method described in the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or applicable local codes.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or applicable local codes.

200234-01C

www.factorybuysdirect.com

7

AIR FOR COMBUSTION AND VENTILATION

VENTILATION AIR

Ventilation Air From Inside Building
This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12″ of the ceiling and one within 12″ of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and
Ventilation for required size of ventilation grills or ducts.

Ventilation Grills Into Adjoining
Room, Option 1

Or Remove Door into Adjoining Room, Option
3

12″
Ventilation Grills Into Adjoining Room,
Option 2

Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12″ of the ceiling and one within 12″ of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for
Combustion and Ventilation for required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

Outlet Air

Outlet Air

Ventilated Attic
To Attic

12″
Figure 2 – Ventilation Air from Inside Building

Inlet Air
Inlet Air

To Crawl Space
Ventilated Crawl Space

Figure 3 – Ventilation Air from Outdoors

8

www.factorybuysdirect.com

200234-01C

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.
WARNING: A qualified service person must install heater. Follow all local codes.
WARNING: Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. Creosote will ignite if highly heated. A dirty chimney flue may create and distribute soot within the house. Inspect chimney flue and firebox for damage. If damaged, repair flue before operating heater.
WARNING: Seal any fresh air vents or ash clean-out doors located on floor or wall of fireplace. If not, drafting may cause pilot outage or sooting. Use a heat-resistant sealant. Do not seal chimney flue damper.

WARNING: Never install the heater · in a bedroom or bathroom · in a recreational vehicle · where curtains, furniture, cloth-
ing, or other flammable objects are less than 36″ from the front, 42″ from top, or 16″ from sides of the heater. · in high traffic areas · in windy or drafty areas
CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.
NOTICE: State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes.
WARNING: This appliance is designed for installation in only a solid-fuel burning masonry or UL 127 factory-built fireplace or in a listed ventless firebox enclosure. Exception: DO NOT install this appliance in a factory-built fireplace that includes instructions stating it has not been tested or should not be used with unvented gas logs.

200234-01C

www.factorybuysdirect.com

9

INSTALLATION

IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form too much moisture. See Air for Combustion and Ventilation, pages 7 and 8. Before beginning assembly or operation of the product, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Before installing heater, make sure you have the items listed below: · Hardware package (provided with heater) · Electric drill with 3/16″ drill bit · Phillips screwdriver
CHECK GAS TYPE
Be sure your gas supply is right for your heater. Otherwise, call dealer where you bought the heater for proper type heater.
CLEARANCES TO COMBUSTIBLES
WARNING: Maintain the minimum clearances. If possible, provide greater clearances from floor, ceiling, and adjoining wall. Measure from outermost point of heater.
Minimum Fireplace Clearance To Combustible Materials
Side Wall 16″, Ceiling 42″, Front 36″
LOG SIZING REQUIREMENTS
Minimum Firebox Size 18″ Log Set: Height 20″, Depth 13″,
Front Width 29″, Rear Width 22″
Minimum Clearances For Side Combustible Material, Side Wall
and Ceiling A. Clearance from the side of the fireplace
cabinet to any combustible material and wall should follow diagram in Figure 4. B. Clearance from the top of the fireplace opening to the ceiling must not be less than 42″.

• *Minimum 16″ from Side Wall Figure 4 – Minimum Clearance for Combustible to Wall
  Minimum Noncombustible Material Clearances
  If Not Using Mantel Note: If using a mantel, proceed to If Using Mantel. If not using a mantel, follow the information below. You must have noncombustible material(s) above the fireplace opening. Noncombustible materials (such as slate, marble, tile, etc.) must be at least 1/2″ thick. With sheet metal, you must have noncombustible material behind it. Noncombustible material must extend at least 12″ up (for all models). See Figure 5 for minimum clearances.
  Requirements for Safe Installation (A) 12″ or more: Noncombustible material OK. (A) Between 8″ and 12″: Install fireplace hood accessory. (A) Less than 8″: Noncombustible
  material must be extended to at least 8″. See Between 8″ and 12″, above. If you cannot extend material, you must operate
  heater with flue damper open.
  Noncombustible Material Distance

Figure 5 – Heat Resistant Material (Slate, Marble, Tile, etc.) Above Fireplace

10

www.factorybuysdirect.com

200234-01C

INSTALLATION

If Using Mantel
You must have noncombustible material(s) above the fireplace opening. Noncombustible materials (such as slate, marble, tile, etc.) must be at least 1/2″ thick. With sheet metal, you must have noncombustible material behind it. Noncombustible material must extend

at least 8″ up. If noncombustible material is less than 12″, you must install the fireplace hood accessory. Even if noncombustible material is more than 12″, you may need the hood accessory to deflect heat away from your mantel shelf. See Figures 5, 6 and 7, for minimum clearances.

MANTEL CLEARANCES

In addition to meeting noncombustible material clearances, you must also meet required clearances between fireplace opening and mantel shelf. If you do not meet the clearances listed below, you will need a hood.
Determining Minimum Mantel
Clearance If you meet minimum clearance between mantel shelf and top of fireplace opening, a hood is not required (see Figure 6).
Determining Minimum Mantel
Clearance When Using a Hood If minimum clearances in Figure 6 are not met, you must have a hood. When using a hood there are still certain minimum mantel clearances required. Follow minimum clearances shown in Figure 7, when using hood.

Minimum Noncombustible Material

10″ 8″ 6″ 2 1/2″

Mantel Shelf

Underside of Mantel Shelf

All minimum distances are in inches
(A) 8″ 8″ 14″ 16″ 20″ 18″ Log Set

Minimum Noncombustible Material Height

Distances to Underside of Mantel

Top of Fireplace Opening

Figure 6 – Minimum Mantel Clearances Without Using Hood

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.
NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following: · operate the logs only with the
flue damper open · raise the mantel to an accept-
able height · move the mantel

Minimum Noncombustible Material

Mantel Shelf 12″

10″

Underside

8″

of Mantel

6″

Shelf

2½”

8″ 12″ 15″ 18″ 20″ Min.

Hood

Distances to Underside of Mantel

Top of Fireplace Opening

Figure 7 – Minimum Mantel Clearances When Using Hood

200234-01C

www.factorybuysdirect.com

11

INSTALLATION

FLOOR CLEARANCES

A. If installing appliance on the floor level, you must maintain the minimum distance of 14″ to combustibles (see Figure 8).

B. If combustible materials are less than 14″ to the fireplace, you must install appliance at least 5″ above the combustible flooring (see Figure 9).

Combustible

14″

Material

Min.

Noncombustible Material

Hearth
5″ Min.

Combustible Material

Figure 8 – Minimum Fireplace Clearances Figure 9 – Minimum Fireplace Clearances

If Installed at Floor Level

Above Combustible Flooring

INSTALLING HEATER BASE ASSEMBLY

WARNING: You must secure this heater to fireplace floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak.
WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure adequate air flow and guard against sooting and controls being damaged. Raise fireplace floor with noncombustible material. Make sure material is secure.

Installation Items Needed · hardware package (provided with heater)
· electric drill with 3/16″ masonry drill bit
1. Position heater base assembly in fireplace. Center base assembly left to right and front to back inside fireplace.
2. Mark screw locations through holes in mounting brackets (see Figure 10). If installing in a brick-bottom fireplace, mark screw locations in mortar joint of bricks.
3. Remove heater base from fireplace.
4. Drill holes at marked locations using 3/16″ drill bit.
5. Attach base assembly to fireplace floor using two masonry screws provided in hardware package (see Figure 10).
6. Connect to gas supply. See Connecting To Gas Supply, page 15.

CAUTION: Do not pick up heater base assembly by burners. This could damage heater. Only handle base assembly by grates.

Masonry Screw

IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will not work properly.

Figure 10 – Attaching Heater Base to Fireplace Floor

12

www.factorybuysdirect.com

200234-01C

INSTALLATION

GAS SELECTION

This appliance is factory preset for propane gas. No changes are required for

Yellow Natural Gas Plunger Underneath Metal Cap

connecting to propane. Only a

qualified installer or service technician can perform gas selection and connecting to gas supply.

Blue Propane Gas Plunger

CAUTION: Two gas line installations at the same time are
prohibited.

CAUTION: To avoid gas leakage for the gas not being used at the inlet of regulator, a qualified installer or service technician must use supplied cap. You will notice a color coded plunger on the inside of the regulator. This is normal. When the inlet connection fitting is inserted and tightened, this plunger will be pushed back by the fitting making all of the adjustments for the gas being supplied. DO NOT REMOVE THE PLUNGER. The regulator will not work and the warranty will be voided.
The inlet regulator is color coded for identification of the correct gas type. Blue is for propane (LP gas) and yellow is for natural gas.

Insert Gas Fitting for Natural Gas

Insert Gas Fitting for Propane Gas

Figure 11 – Gas Regulator

FOR PROPANE GAS
INSTALLATION: BLUE
Apply thread sealant to the threads on the connection fitting. While pushing in, rotate the fitting clockwise until the threads engage the regulator. After the fitting has been hand tightened into the regulator use a wrench to complete tightening of the fitting. Install additional fitting to connect to the house supply.

DO NOT REMOVE Blue Propane Plunger Install Gas Fitting Here
Fitting supplied by installer, may
vary.

200234-01C

www.factorybuysdirect.com

13

INSTALLATION
FOR NATURAL GAS INSTALLATION: YELLOW 1. Remove the metal cap installed over the NG regulator inlet.

Metal Cap
2. Install metal cap over propane regulator inlet. This will keep debris out of regulator.

DO NOT REMOVE Yellow Natural Gas Plunger

Metal Cap

Install Gas Fitting Here

Use only the cap supplied on the regulator. Do not use an off the shelf pipe plug. This can damage the plunger. The supplied regulator cap is designed so it will not engage the unused gas type.
3. Apply thread sealant to the threads on the connection fitting. While pushing in, rotate the fitting clockwise until the threads engage the regulator. After the fitting has been hand tightened into the regulator use a wrench to complete tightening of the fitting. Install additional fitting to connect to the house supply.

Use only the metal cap. DO NOT use an off the shelf 3/8″ NPT pipe plug. This will damage the plungers located inside the regulator.
DO NOT TRY TO REMOVE THE PLUNGERS FROM INSIDE THE REGULATOR. THE PLUNGER WILL BE PUSHED BACK AS THE FITTING IS INSTALLED. REMOVING THE PLUNGERS WILL VOID THE WARRANTY.
Make sure the type of gas being used is correct. Check to make sure the connection fitting is in the correct inlet on the regulator. Refer to Connecting to Gas Supply, page 15. If you are using natural gas and the pilot will not light, see Troubleshooting, page 25.

14

www.factorybuysdirect.com

200234-01C

INSTALLATION

CONNECTING TO GAS SUPPLY

WARNING: A qualified service technician must connect heater to gas supply. Follow all local codes.
WARNING: This appliance requires a 3/8″ NPT (National Pipe Thread) brass inlet connection to the pressure regulator.
WARNING: For natural gas, Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.
CAUTION: For propane gas, never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane supply. Gas supplier provides external regulator for natural gas. The installer provides the external regulator for propane gas.
WARNING: Do not overtighten gas connections.
CAUTION: Use only new, black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2″ diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of pressure will occur.

CAUTION: For natural gas, check your gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 9.5″ WC. If gas line pressure is higher, heater regulator damage could occur.
CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting into gas piping and/or fittings.
CAUTION: Use pipe joint sealant that is resistant to gas (Propane or Natural Gas).
Before installing heater, make sure you have the items listed below: · external regulator for propane unit only
(supplied by installer) · piping (check local codes) · sealant (resistant to natural gas and pro-
pane gas) · equipment shutoff valve · test gauge connection · sediment trap · tee joint · pipe wrench · flexible gas hose (check local codes) · 3/8″ NPT brass fitting * A CSA design-certified equipment shutoff valve with 1/8″ NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design certified equipment shutoff valve from your dealer.

200234-01C

www.factorybuysdirect.com

15

INSTALLATION

Typical Inlet Pipe Diameters
Use 3/8″ black iron pipe or greater. Installation must include an equipment shutoff valve, union, and plugged 1/8″ NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 13).
IMPORTANT: Install an equipment shutoff
valve in an accessible location. The equip-
ment shutoff valve is for turning on or shutting
off the gas to the appliance.
For propane installations, apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.
The installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11″ WC and 14″ WC. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 14. Pointing the vent down protects it from freezing rain or sleet.

Install sediment trap in supply line as shown in Figure 13. Place sediment trap where it is within reach for cleaning. Place sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once (see page 17).

Heater Gas Regulator

Fitting

LP IMNALXET1/G2APSSIPGR(E3S.5SKUPRAE)
Gas esté Gas Inlet
NG

Flexible Gas Hose (if allowed by local codes)

Figure 12 – Attaching Flexible Gas Hose to Heater Gas Regulator (may vary from
illustration)

Ground Joint Union

Tee Joint

Test Gauge Connection*

Reducer Bushing to 1/8″ NPT
1/8″ NPT Plug Tap

Sediment Trap

Tee Joint Pipe Nipple Gap

3/8″ NPT Pipe Nipple
Equipment Shutoff Valve Propane Natural Gas Supply Tank From Gas Meter (5″ W.C.** to 9.5″ W.C. Pressure)

External Regulator with Vent Pointing Down

3″ Minimum

Propane From External Regulator (11″ W.C.** to 14″ W.C. Pressure)

Figure 13 – Gas Connection

Figure 14 – External Regulator

• Purchase the optional CSA design-certified equipment with Vent Pointing Down

shutoff valve from your dealer.

16

www.factorybuysdirect.com

200234-01C

INSTALLATION

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections, internal and
external to unit, for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. If bubbles form, there is a leak. Correct all leaks at once.

PRESSURE TESTING GAS SUPPLY PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect heater with its appliance main

located on or near gas meter for natural

gas valve (control valve) and equipment

gas or using compressed air.

shutoff valve from gas supply piping system. Pressures in excess of 1/2 PSIG will damage heater regulator.

4. Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to all joints. If bubbles form, there

2. Cap off open end of gas pipe where equip-

may be a leak.

ment shutoff valve was connected.

5. Correct all leaks at once.

3. Pressurize supply piping system by either opening propane supply tank valve for propane gas or opening main gas valve

6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 15).
2. Pressurize supply piping system by either opening propane supply tank valve for propane gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.

Propane Supply Tank

Equipment Shutoff Valve

3. Check all joints from gas meter to equip-

ment shutoff valve for natural gas or

propane supply to equipment shutoff valve

for propane (see Figure 16 or 17). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.
4. Correct all leaks at once.

External Regulator

Control Valve Location

Figure 16 – Checking Gas Joints for Propane Gas

Equipment Shutoff Valve

Open

External Regulator Supplied by Gas Supplier
Gas

Meter

Closed Figure 15 – Equipment Shutoff Valve

200234-01C

Equipment Shutoff Valve

Control Valve Location

Figure 17 – Checking Gas Joints for

Natural Gas

www.factorybuysdirect.com

17

INSTALLATION

PRESSURE TESTING HEATER GAS CONNECTIONS

1. Open equipment shutoff valve (see Figure 15, page 17).
2. Open main gas valve located on or near gas meter for natural gas or open propane supply tank valve.
3. Make sure control knob of heater is in the OFF position.
4. Check all joints from equipment shutoff valve to control valve (see Figure 16 or

17, page 17). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Light heater (see Lighting Instructions on page 19). Check all other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas Appliance, page 20).

INSTALLING LOGS See Log Assembly Instructions included with your log set for proper log installation.

INSTALLING BATTERIES

CAUTION: Do not mix old and

new batteries. Do not mix alka-

AAA

line, standard (carbon – zinc), or

Battery Positive

rechargeable (nickel – cadmium)

UP

batteries. Do not dispose of

batteries in fire, batteries may

explode or leak.

· Batteries are included.
· Remove batteries when depleted.
· Install/replace the batteries according to the type and quantity stated in table below.
· Do not mix old and new batteries. New batteries should be the same brand for best results.
· Be sure to observe proper polarity (+/-) when installing or replacing the batteries. Damage due to improper battery installation may void the warranty on the product.
· For remote control systems, maximize battery life by turning off the receiver when it is not in use.
· For long periods of non-operation, remove batteries from all components for safety.

Component Ignitor
Remote Control Remote Receiver

Type of Battery AAA AAA AA

Qty. 1
2 or 3* 4

*Note: Quantity depends on model of remote control.

Figure 18 – Installing Battery in Ignitor
Receiver and Remote Control Batteries are required in both the Remote Control (Transmitter) (2 AAA size) and Receiver (4 AA size) (see Figure 19). Note: Be sure batteries are placed correctly. Reversing the batteries can cause damage to the receiver and remote. Replace all batteries on a yearly basis or sooner.
Position the slide switch on the front of the receiver box in the ON position before installing batteries. Once the batteries are installed you will hear a single beep which indicates the batteries are charged. If you do not hear a beep, replace with new batteries.
Receiver
OFF REMOTE ON

AA AA AA AA

LEARN

AAA

AAA

Ignitor
Unscrew ignitor cap and install a AAA battery with the + pointing out. Replace cap.

Remote Control (Transmitter)
Figure 19 – Installing Batteries in Remote Control and Receiver

18

www.factorybuysdirect.com

200234-01C

OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS · Do not try to light any appliance. · Do not touch any electric switch; do

not use any phone in your building. · Immediately call your gas supplier
from a neighbor’s phone. Follow the gas supplier’s instructions. · If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

WARNING: You must operate this log set with the fireplace screen in place. Make sure screen is installed before running heater.

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.

1. STOP! Read the safety information above.

2. Make sure equipment shutoff valve is fully open.

3. Push in control knob slightly and turn

clockwise

to the OFF position.

4. Wait five (5) minutes to clear out any gas. Then smell for gas around heater and near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you do not smell gas, go to the next step.

5. Push in control knob slightly and turn coun-

terclockwise

to the PILOT position.

Press in control knob for five (5) seconds.

Note: The first time that the heater is operated after connecting the gas supply, the
control knob should be pressed for about
thirty (30) seconds. This will allow air to
bleed from the gas system. If pilot does not
stay lit, refer to Troubleshooting, pages 25 though 28. Also contact a qualified service technician or gas supplier for repairs. Until
repairs are made, light pilot with match.
· If control knob does not pop up when released, contact a qualified service technician or gas supplier for repairs.
6. With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the rear of the burner. If needed, keep pressing ignitor button until pilot lights. Note: If pilot does not stay lit, refer to
Troubleshooting, pages 25 though 28. Also contact a qualified service technician or gas supplier for repairs. Until repairs are
made, light pilot with match. To light pilot
with match, see Manual Lighting Procedure, page 20. 7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note: If pilot goes out, repeat steps 3
through 7. This heater has a safety inter-

lock system. Wait one (1) minute before

lighting pilot again.

200234-01C

www.factorybuysdirect.com

19

OPERATION

8. Be sure the slide switch on the front of the receiver box is in the ON position.
9. Turn control knob counterclockwise to the ON position. The main burner should light. Note: If burner does not light, push the slide switch on the receiver box to the OFF position, then back to the ON position.
Note: Please wait one minute after shutting off heater to allow the control valve to reset before starting again.
10. Make sure fireplace screen is in place before operating heater.

11. If heater will not operate, follow the instructions To Turn Off Gas To Appliance, and call your service technical or gas supplier.
CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.
WARNING: If input gas type is NG, make sure NG pilot burner ignites. If input gas type is LP, make sure LP pilot burner ignites.

Natural Gas Ignitor

Burner

Electrode

Thermocouple
Propane Gas Burner

Ignitor Button
Control Knob Figure 20 – Ignitor Button and Control
Knob Locations

Pilot Air Inlet Hole

(Back of pilot shown for clarity)

Pilot Air Inlet Hole

Figure 21 – Pilot

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater
Turn control knob clockwise OFF position.

to the

Shutting Off Burner Only

(pilot stays lit)

Turn control knob clockwise

to the

PILOT position.

MANUAL LIGHTING PROCEDURE

1. Follow steps 1 through 7 under Lighting Instructions, page 19.
2. With control knob in PILOT position, strike match, and hold near pilot. Press in control knob; pilot should light.

3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.
4. Make sure the fireplace screen is in place before operating heater.

20

www.factorybuysdirect.com

200234-01C

OPERATION

REMOTE CONTROL SYSTEM

Programming the Remote and Receiver The remote and receiver must be “learned” to one another. To prepare the receiver box for learning, use a pen or small screwdriver to gently press and hold the learn button until you hear 3 series of beeps. 1. Place the slide switch on the receiver in
the remote position (see Figure 22). 2. Turn control knob on the heater to the ON
position. 3. Use a pen or small screwdriver to gently
press and hold the recessed LEARN button on the face of the receiver for 2-3 seconds. You will hear a beep. 4. Press the ON button on the remote control to light the burner (see Figure 24). You will hear a series of beeps. This will also “learn”, or program, the remote and the receiver. Note: Remote must be at least 5 feet away from the receiver during the learning process. Note: If the remote control is lost or damaged, the slide switch on the receiver can be used to operate the heater. Note: When batteries are replaced the learning process above must be repeated.
Learn Button
LEARN
ON REMOTE OFF

Key Settings ON – Operates unit to on position, manually operated solenoid ON. OFF – Operates unit to off position, manually operated solenoid OFF. MODE – Changes unit from manual mode to thermo mode. SET – Sets temperature in thermo mode.
TEMP
Figure 23 – Remote Control LCD Liquid Crystal Display 1. DISPLAY Indicates CURRENT room temperature. 2. °F or °C Indicates degrees Fahrenheit or Celsius. 3. FLAME Indicates burner/valve in operation. 4. ROOM Indicates remote is in THERMO operation. 5. TEMP Appears during manual operation. 6. SET Appears during time the of setting the desired temperature in the thermo operation.

Slide Switch Figure 22 – Receiver

2 1
3 4 ROOM SET TEMP 5

Remote Control Operation
This appliance must not be used with glass doors in the closed position. This can lead to pilot outages and severe sooting outside the fireplace.
The transmitter operates on 2 AAA batteries.

6 Figure 24 – Remote Control Display

200234-01C

www.factorybuysdirect.com

21

OPERATION

Setting°F/°C Scale The factory setting for temperature is °F. To change this setting to °C, press the ON key and the OFF key on the remote control at the same time (see Figure 23, page 21). This will change from °F to °C. Follow this same procedure to change from °C back to °F.
Manual Function To operate the system in the manual “MODE” do the following. ON OPERATION Press the ON key and the appliance flame will come on. During this time the LCD screen will show ON (see Figure 25). After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (see Figure 25). The flame icon will appear on LCD screen in manual on mode.
TEMP
Figure 25 – Manual Mode in ON Operation
OFF OPERATION Press the OFF key and the appliance flame will shut off. During this time the LCD screen will show OF (see Figure 26). After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (see Figure 26).
TEMP
Figure 26 – Manual Mode in OFF Operation
THERMOSTAT FUNCTION Setting Desired Room Temperature The remote control system can control the thermostat when the transmitter is in the THERMO mode. The word ROOM must be displayed on the screen. To set the THERMO MODE and desired room temperature: 1. Press the MODE key until the LCD screen
shows the word ROOM. The remote is now in the thermostatic mode.

2. Press and hold the SET key until the desired set temperature is reached. The LCD screen set numbers will increase from 45° to 99° and then restart over at 45°.
3. Release the SET key. The LCD screen will display the set temperature for 3 seconds, then flash the set temperature for 3 seconds, then LCD screen will default to display the room temperature.
To Change The Set Temperature
1. Press and hold the SET key until the desired set temperature is reached. The LCD screen set numbers will increase from 45° to 99° then restart over at 45°.
2. Release the SET key. The LCD screen will display the set temperature for 3 seconds, then flash the set temperature for 3 seconds, then the LCD screen will default to display the room temperature.
3. Press the MODE key to disengage the thermo mode. The word ROOM on the LCD screen will not show when the thermo is not in operation.
Note: The highest SET temperature is
99°F (32 °C) and the lowest temperature
is 45°F (6°C).
REMOTE CONTROL OPERATION
NOTES
The Thermo Feature on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a certain number of degrees from the SET TEMPERATURE.
This variation is called the “swing” or temperature differential. The normal operating cycle of an appliance may be 4 times per hour depending on how well the room or home is insulated from the cold or drafts. The factory setting for the “swing number” is 2. This represents a temperature variation of +/-2°F (1°C) between SET temperature and ROOM temperature, which determines when the fireplace will be activated. The transmitter has ON and OFF manual functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen to show while the signal is being sent. Upon initial use, there may be a delay of three seconds before the remote receiver will respond to the transmitter. This is part of the system’s design.

22

www.factorybuysdirect.com

200234-01C

INSPECTING BURNERS

IMPORTANT: Owner’s should check pilot flame pattern and burner flame pattern often. Incorrect flame patterns indicate the need for cleaning (see Care and Maintenance, page 24) or service.

WARNING: Only a qualified service person should service and repair heater. This includes maintenance requiring replacement or alteration of components.

PILOT FLAME PATTERN

Figure 27 shows a correct pilot flame pattern. Figure 28 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool, which shuts the heater off.

Notice: Do not mistake orange flames with yellow tipping. Dirt or other fine particles enter the heater and burn causing brief patches of orange flame.

If pilot flame pattern is incorrect, as shown in Figure 28

Natural Gas Shown

· turn heater off (see To Turn Off Gas to Ap-

NG 3-3.5″ WC

LP 8-11″ WC

pliance, page 20)

· see Troubleshooting pages 25 through 28.

WARNING: If yellow tipping occurs, your heater could produce increased levels of carbon monoxide. If the burner flame pattern shows yellow tipping, follow instructions at bottom of this page.

Figure 27 – Correct Pilot Flame Pattern (Natural Gas shown)

Natural Gas Shown
NG 3-3.5″ WC

LP 8-11″ WC

Figure 28 – Incorrect Pilot Flame Pattern (Natural Gas shown)
BURNER FLAME PATTERN Figure 29 shows a correct burner flame pattern. Figure 30 shows an incorrect burner flame pattern. If burner flame pattern is incorrect then: · turn heater off (see To Turn Off Gas to Appliance, page 20). · see Troubleshooting pages 25 through 28. More Than 8″ Above Top of Logs
Approx. 3″-6″ Above Top of Logs

Figure 29 – Correct Burner Flame Pattern Figure 30 – Incorrect Burner Flame Pattern (Actual logs will vary from illustration.)

BURNER PRIMARY AIR HOLES
Air is drawn into the burner through the holes in the fitting at the entrance to the burner. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean as necessary. Blocked air holes will create soot.

200234-01C

www.factorybuysdirect.com

23

CARE AND MAINTENANCE

WARNING: Turn off heater and let cool before servicing.

CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service technician. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit.

MAIN BURNER

Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some

burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off the heater and let it cool, and remove blockage or replace burner. Blocked burner flame holes will create soot.

BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

We recommend that you clean the unit every 2,500 hours of operation or every three months. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSl. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly.
1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.
5. Blow air into the primary air holes on the injector holder.
6. In case any large clumps of dust have now been pushed into the burner. Repeat steps 3 and 4.
Burner Tube

2. Inspect burner, pilot and primary air inlet holes on injector for dust and dirt (see Figure 31).

Primary Air Inlet Holes Injector Figure 31 – Burner and Injector Holder

3. Blow air through the ports/slots and holes in the burner. Also clean the pilot assembly.

24

www.factorybuysdirect.com

200234-01C

CARE AND MAINTENANCE

ODS/PILOT

Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean.
A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about 2″ from where the pilot flame comes out of the pilot assembly (see Figure 32). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Natural Gas Ignitor

Burner

Electrode

Thermocouple
Propane Gas Burner

Pilot Air Inlet Hole
(Back of pilot shown for clarity)

Pilot Air Inlet Hole

Figure 32 – Pilot Inlet Air Hole

CABINET

Air Passageways

Exterior

Use a vacuum cleaner or pressurized air to · Use a soft cloth dampened with a mild soap

clean.

and water mixture.

· Wipe the cabinet to remove dust.

LOGS · If you remove logs for cleaning, refer to your log set owners manual to properly replace logs. · Replace log(s) if broken or chipped (dime-size or larger).

TROUBLESHOOTING

WARNING: If you smell gas: · Shut off gas supply. · Do not try to light any appliance. · Do not touch any electrical switch; do not use any phone in your
building. · Immediately call your gas supplier from a neighbor’s phone. Fol-
low the gas supplier’s instructions. · If you cannot reach your gas supplier, call the fire department.
WARNING: Only a qualified service technician should service and repair heater. Make sure that power is turned off before proceeding. Turn off and let cool before servicing.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time. Note: All troubleshooting items are listed in order of operation.

200234-01C

www.factorybuysdirect.com

25

TROUBLESHOOTING

Problem

Possible Cause

Corrective Action

Using natural gas and I n l e t p r e s s u r e e x c e e d s Bypass pressure switch. See

pilot will not light.

9.5″ WC.

instructions below.

Pressure Switch
When using natural gas, there is a pressure switch that acts to turn off the gas flow to the pilot if the inlet pressure exceeds 9.5″ WC. This is to prevent the operation of the unit on the wrong gas (propane). If your natural gas supply exceeds 9.5″ WC the unit will not operate. Either contact your gas supplier to check and adjust the inlet pressure or a qualified service technician can bypass the pressure switch.
Before attempting to bypass the pressure switch, make sure the type of gas being used is correct. Check to make sure the connection fitting is in the correct inlet on the regulator. Refer to Connecting to Gas Supply, page 15.
Only a qualified installer should bypass the pressure switch. To bypass the pressure switch locate the set screw on the regulator. Use a small flat bladed screw driver to turn the set screw counterclockwise 2 turns. This will bypass the pressure switch function.

NG

The entire gas delivery piping including connections inside the heater should be leak tested by the qualified installer. After leak testing the qualified installer should light the appliance. Refer to the correct flame pattern as illustrated on page 23. All flame patterns should be safely inside the product. If for any reason they are not, stop use of the appliance and call for repairs.
Pressure Switch Set Screw Figure 33 – Gas Regulator Pressure Switch

Problem When ignitor button is pressed in, there is no spark at ODS/pilot
When ignitor button is pressed in there is a spark at ODS/pilot but no ignition.
26

Possible Cause

Corrective Action

1. Low battery. 2. Ignitor electrode is not con-
nected to ignitor cable. 3. Ignitor cable is pinched or
wet.
4. Ignitor electrode is positioned wrong. Ignitor electrode is broken.
5 Broken ignitor cable. 6. Bad piezo ignitor.

1. Replace battery. 2. Reattach ignitor cable
3. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry.
4. Replace electrode.
5. Replace ignitor cable. 6. Replace piezo ignitor.

1. Gas supply is turned off or equipment shutoff valve is closed.
2. Control knob not in PILOT position.
3. C o n t r o l k n o b n o t f u l l y pressed in while pressing ignitor button.
4. Air in gas lines (new installation or recent gas interruption).
5. ODS / pilot is clogged.
6. Depleted gas supply (propane).

1. Turn on gas supply or open equipment shutoff valve.
2. Turn control knob to PILOT position.
3. Fully press in control knob while pressing ignitor button.
4. Continue holding down control knob. Repeat igniting operation until air is removed.
5. Clean ODS/pilot (see Care and Maintenance, page 24) or replace ODS/pilot assembly.
6. Contact local propane gas company.

www.factorybuysdirect.com

200234-01C

TROUBLESHOOTING

Problem

Possible Cause

Corrective Action

ODS/pilot lights but flame goes out when control knob is released.

1. Control knob is not fully pressed in.
2. Control knob is not pressed in long enough.
3. Equipment shutoff valve is not fully open.
4. Thermocouple connection is loose at control valve.
5. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This problem could be caused by one or both of the following: A) Low gas pressure B) Dirty or partially clogged ODS/pilot
6. Thermocouple damaged. 7. Control valve damaged.

1. Press in control knob fully.
2. After ODS/pilot lights, keep control knob pressed in 30 seconds.
3. Fully open equipment shutoff valve.
4. Hand tighten until snug, and then tighten 1/4 turn more.
5. A) Contact local natural or propane gas company
B) Clean ODS/pilot (see Care and Maintenance, page 24) or replace ODS/ pilot assembly
6. Replace thermocouple. 7. Contact customer service

Burner does not light after ODS/pilot is lit.

1. Burner orifice is clogged.
2. Inlet gas pressure is too low. 3. Burner orifice diameter is too
small.

1. Clean burner orifice (see Care and Maintenance,
page 24). 2. Contact local gas supplier. 3. Replace heater chassis.

Delayed ignition of 1. Manifold pressure is too low. 1. Contact local gas supplier.

burner.

2. Burner orifice is clogged. 2. Clean burner (see Care and

Maintenance, page 24).

Burner backfiring during combustion.

1. Burner orifice is clogged or damaged.
2. Burner is damaged.
3. Gas regulator is damaged.

1. Clean burner orifice (see Care and Maintenance,
page 24). 2. Contact dealer or customer
service. 3. Replace heater chassis.

Yellow flame during burner combustion.

1. Not enough air.
2. Inlet gas pressure is too low. 3. Gas regulator is damaged.

1. Check burner for dirt and debris. If found, clean burner (see Care and Maintenance, page 24).
2. Contact local gas supplier. 3. Replace heater chassis.

Slight smoke or odor 1. Residues from manufactur- 1. Problem will stop after a few

during initial operation.

ing process.

hours of operation.

Gas odor during combustion.

1. Foreign matter between control valve and burner.
2. Gas leak. (See Warning Statement at top of page 25).

1. Contact a qualified service technician to remove foreign matter.
2. Locate and correct all leaks (see Checking Gas Connections, page 17).

200234-01C

www.factorybuysdirect.com

27

TROUBLESHOOTING

Problem

Possible Cause

Corrective Action

Heater produces unwanted odors.

1. Heater is burning vapors from paint, hair spray, glues, etc. See IMPORTANT statement, page 25.
2. Gas leak. See Warning Statement at the top of page 25.
3 Low fuel supply.

1. Open a window to ventilate room. Stop using odor causing products while heater is running.
2. Locate and correct all leaks (see Checking Gas Connections, page 17).
3. Refill supply tank (Propane models).

Heater produces a whistling noise when burner is lit.

1. Turning control knob to high position when burner is cold.
2. Air in gas line.
3. Air passageways on heater are blocked.
4. Dirty or partially clogged burner orifice.

1. Turn control knob to low position and let warm up for a minute.
2. Operate burner until air is removed from line. Have gas line checked by local gas supplier.
3 Observe minimum installation clearances (Figure 4, page 10).
4 Clean burner (see Care and Maintenance, page 24).

Heater produces a clicking/ticking noise just after burner is lit or shut off.

1. Metal is expanding while heating or contracting while cooling.

1. This is common with most heaters. If noise is excessive, contact qualified service technician.

White powder residue forming within burner box or on adjacent walls or furniture.

1. When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue.

1. Turn heater off when using furniture polish, wax, carpet cleaner or similar products.

Heater shuts off in use (ODS operates).

1. Not enough fresh air is available.
2. Low line pressure. 3. O D S / p i l o t i s p a r t i a l l y
clogged.

1. Open window and/or door for ventilation.
2. Contact local gas supplier. 3. Clean ODS/pilot (see Care
and Maintenance, page 24).

Gas odor exists even when control knob is in OFF position.

1. Gas leak. See Warning Statement at top of page 25.
2. Control valve is defective.

1. Locate and correct all leaks (see Checking Gas Connections, page 17).
2. Contact customer service.

Moisture/condensation 1. Not enough combustion/ 1. Refer to Air for Combus-

noticed on windows.

ventilation air.

tion and Ventilation require-

ments, page 7.

28

www.factorybuysdirect.com

200234-01C

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement parts, call Customer Service toll free at 1-855-607-6557 for referral information.
When calling Customer Service or your dealer, have ready:
· Your name
· Your address

· Model and serial number of your heater · How heater was malfunctioning · Type of gas supply and Propane tank size · Purchase date Usually, we will ask you to return the defective part to the factory

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s) call Customer Service toll free at 1-855-607-6557 for referral information.

When calling Customer Service have ready: · Model number of your heater · The replacement part number

SERVICE HINTS
When Gas Pressure Is Too Low · pilot will not stay lit · burners will have delayed ignition · fireplace will not produce specified heat · propane gas supply might be low (propane units only) You may feel your gas pressure is too low. If so, contact your local gas supplier.

TECHNICAL SERVICE
You may have further questions about installation, operation, or troubleshooting. If so, contact Factory Buys Direct at 1-855-607-6557. When calling, please have your model and serial numbers of your heater ready.

200234-01C

www.factorybuysdirect.com

29

PARTS MODEL FDLR18-1
This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 29 of this manual.
1

2

TEMP

3

LEARN
ON REMOTE OFF

ITEM

PART #

DESCRIPTION

1 161338-01

Ignitor

3 161334-01

Remote Control

4 161312-01

Remote Receiver

PARTS AVAILABLE – NOT SHOWN

18UDC1013B-01 Hardware Packet

QTY 1 1 1
1

30

www.factorybuysdirect.com

200234-01C

ACCESSORIES

To purchase these heating accessories please visit our website www.factorybuysdirect.com or give us a call at 1-855-607-6557.

EQUIPMENT SHUTOFF VALVE
For all models. Visit us online at www.factorybuysdirect.com for a complete selection of gas connection fittings.

Existing Gas Line

INSTALLATION KIT
Flexible Connector

Shutoff Valve

Flare & Pipe

200234-01C

www.factorybuysdirect.com

31

References

• Ventless Fireplaces, Gas Heaters, Electric Heaters, Gas Log Sets, Fireplace Inserts - Factory Buys Direct

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>