LISTEN TECHNOLOGIES LT-800-072 Stationary RF Transmitter User Manual

LISTEN TECHNOLOGIES LT-800-072 Stationary RF Transmitter

Specifications

• RF Audio Specifications:
  • RF Frequency Range : LT-800-072: 72.025 – 75.950 MHz, LT-800-216: 216.025 – 216.9875 MHz
  • Number of Channels : LT-800-072: 17 wide band, 40 narrow band, LT-800-216: 19 wide band, 38 narrow band
  • Frequency Accuracy : 50 PPM
  • Transmitter Stability : 80,000uV at 3 m
  • Output Power : LT-800-072: Not specified, LT-800-216: 100mW (max allowed by FCC)
  • Antenna: Various Antennas are available
  • Antenna Connector: BNC
  • Compliance : FCC Part 15, Industry Canada
• System Frequency Response:
  • System Signal to Noise Ratio (A-Weighted): LT-800-072: 80 dB SQ enabled; 60 dB SQ disabled, LT-800-216: 80 dB SQ enabled; 50 dB SQ disabled
  • System Distortion : LT-800-072: 60 dB, LT-800-216: 80 dB SQ enabled; 50 dB SQ disabled

Product Usage Instructions

Setup Instructions

1. Unpack the contents of the package.

2. Connect the LT-800 Series Stationary RF Transmitter to a power source using the provided LA-207 12 VDC Power Supply.

3. Refer to the Quick Start Guide for initial setup and configuration.

Operating Instructions

1. Power on the LT-800 Series Stationary RF Transmitter by pressing the power button.

2. Adjust the audio input levels as per your requirements.

3. Select the appropriate channel for transmission.

4. Monitor the headphone output for audio quality.

Troubleshooting

If you encounter any issues with the LT-800 Series Stationary RF Transmitter, refer to the Troubleshooting section in the user manual for guidance. If problems persist, contact Listen for technical support.

FAQ

• Q: How many channels are available in the LT-800-072 Stationary RF Transmitter?
  • A : The LT-800-072 Stationary RF Transmitter offers 17 wide band and 40 narrow band channels for transmission.
• Q: What is the maximum output power of the LT-800-216 Stationary RF Transmitter?
  • A : The LT-800-216 Stationary RF Transmitter has a maximum output power of 100mW, which is the limit allowed by FCC regulations.

Dear Valued Customer,

Thank you for choosing Listen! We are dedicated to providing you with the highest quality products available and take pride in delivering outstanding performance to ensure you are completely satisfied. We independently certify each of our products to the highest quality standards. We are available to answer any questions you might have during installation or in the operation of our products. At Listen, it’s all about you, should you have any comments or suggestions we’re here to listen.

Package Contents

LT-800-072 Contents

• (1) LT-800-072 Stationary RF Transmitter (72 MHz)
• (1) LA-207 12 VDC Power Supply
• (1) Quick Start Guide

LT-803-072 Contents

• (1) LT-803-072 Stationary 3-Channel
• RF Transmitter (72 MHz)
• (1) LA-207 12 VDC Power Supply
• (1) Quick Start Guide

LT-816-072 Contents

• (1) LT-800-216 Stationary RF Transmitter (216 MHz)
• (1) LA-207 12 VDC Power Supply
• (1) Quick Start Guide

Specifications

LT-800 Architectural Specifications

The stationary FM transmitter shall be capable of broadcasting on 57 channels. The transmitter shall have an SNR of 80dB or greater. The output power shall be adjustable to quarter, half or full. Channel tuning shall be capable of being locked. The device shall broadcast on both wide and narrow-band channels. The device shall have an audio frequency response of 63 Hz to 15k Hz, ± 3dB at 72 MHz, or of 63 Hz to 10k Hz, ± 3dB at 216 MHz. It shall have two mixing audio inputs. The device shall have the following audio controls: input level, mix level, and an adjustable low pass filter. The device shall have an audio processor that is capable of automatic gain control and limiting. The Listen LT-800 is specified.

Specifications

Block Diagram

Quick Reference

Back Panel: Connections & Settings 

Setup Instructions

Unpack the Product

Remove the outer packaging and plastic cover. Inspect for physical damage.

Mount in Rack (if necessary)

If rack mounting the unit, install the optional rack mount kit (part LA-326) according to the instructions included with the kit, then install the LT-800/LT-803 in the rack.
NOTE : If rack mounting, you will need to use a rear connection antenna.

Connect Antenna

Connect the antenna (not included) according to the installation instructions. Only use an antenna supplied by Listen. If you are connecting the antenna directly to the top of the LT-800/LT-803, you will need to remove the rubber plug on top of the unit. If you are using a remote antenna connected to the rear of the unit, do not connect an antenna to the top connector.  for antenna options, or refer to the Listen website for remote antenna options, www.listentech.com.

Connect Power

Plug the power supply into the power connector on the back panel, then plug the power supply into an outlet. Only use a Listen-approved power supply (the LA-207, an in-line switching power supply, is the approved power supply for this unit).

Select Phonak Compatibility (if necessary)

If you will be using Phonak receivers with your LT-800 (216 MHz only), the transmitter can become completely compatible through software control. When switched to this mode, the LT-800 transmitter will display the Phonak channels. By integrating Phonak channels and compatibility into the LT-800-216, it is more convenient to use Phonak receivers with Listen transmitters. (www.phonak.com)

To Select Phonak Mode (LT-800 only):

Press and hold down the channel and select the “up” button while powering on the unit. The LCD will display a “P” momentarily upon power up indicating that the transmitter is in the Phonak Channel Mode. The channels displayed will now match Phonak channels. To return to the Listen channel designations, repeat this process. The LCD will display an “L” momentarily upon power up indicating that you are in the Listen Channel Mode.

Select Channel Mode (if necessary)

Your transmitter has been shipped to you with only a limited number of channels available (Basic Mode). If all channels (Expanded Mode) are required, use the following procedure.

To Select Expanded Mode (LT-800 only):

To enable or disable the Expanded Mode, press and hold the channel and select the “down” button while powering on the unit. When the Basic Mode is enabled, “L/O” (lockout) will be displayed on the LCD display as shown below. This indicator is extinguished when in the Expanded Mode.

Set SQ (Super Quiet) and Process Features (SQ available on LT-800 only):

Your transmitter is shipped to you with SQ (super quiet) enabled and Process disabled. For a detailed description of these features and when to use them, please refer to page 11.

To Disable or Enable SQ and Process Features:

With the unit on press and hold the channel select the “Down” button for 8 seconds. The program (PGM) icon will appear on the LCD.

Once in the program mode,

the SQ and process features can be turned on and off by pressing the channel select buttons. Press the channel and select the “Up” button to toggle between Process On and Off. Press the channel and select the “Down” button to toggle between SQ On and Off.

If the green LED is illuminated on the front panel, that feature is enabled. Once you have enabled or disabled the features as desired, let the transmitterexit the program mode by waiting 5 seconds.

Set RF Power

Set the RF POWER switch on the back of the unit to Full, 1/2 or 1/4 (Level is indicated on the LCD display). The amount of transmitted RF power that you will need depends on your application. If youare operating multiple transmitters in the same environment, it is best to set the transmitter’s output power to its lowest level to reduce the possibility of interference.

Connect Audio Inputs

The LT-800/LT-803 has two audio input options: Input 1 and Input 2. Input 1 is a balanced connection using either an XLR or 1/4” phono connector. Input 2 has two unbalanced mixing phono connectors. Use Input 1 if you are using a microphone or if you have a balanced connection such as from a professional audio mixer (you can also use Input 1 for unbalanced connections). Use Input 2 to connect to an unbalanced audio source.

Input 1

Connect the audio source(s) to one or both audio input connections. Input 1 offers a choice of balanced XLR or 1/4” phono connector.
Plug your microphone into Input 1 and move the input select switch to Mic (for dynamic microphones) or Mic + PH Power (for condenser microphones).

Plug your balanced or unbalanced audio source into Input 1. Use the following diagram.

Input 2

Plug your unbalanced audio source into Input 2 and select the audio level switch for –10dBu or +10dBu, to match the audio level coming from your equipment.

Operating Instructions

• Power Unit On
  • Turn the power on by pressing the power button.
• Select a Channel
  • Select the transmit channel by pressing the channel select UP and DOWN buttons. See Channel Selection on page 13 for more information.

NOTE : The LT-800 is shipped with only limited channels (Basic Mode). To select from all channels (Expanded Mode) (for a more detailed description of Basic and Expanded Mode ).

Lock on Channel

Once you determine your transmit channel, you can lock the transmitter on that channel. To lock a channel hold the Channel Select “Up” button for 3 seconds until the padlock icon appears on the display. To unlock, repeat this process and the padlock icon will disappear

Test Tone (if necessary)

To broadcast a test tone, press the test tone button. This helps to test receivers when no audio source is available.

Audio Control

• Adjust the Audio Input Level
  • Adjust the input knob counterclockwise to add gain to Input 1. This will decrease the gain to Input 2. Adjust the input knob clockwise to add gain to Input 2. This will decrease the gain to Input 1. If you have two audio sources connected to both Input 1 and 2, adjust the level of one input using the VU meter, then adjust the output level of the other audio source. Adjust the input level until the left VU meter(s) occasionally illuminate the red LEDs. Illumination of the red LEDs indicates the unit is in limiting. Limiting is required so that the unit does not over-modulate the transmitter. If you don’t want any audio limiting to occur, make sure the red LEDs never illuminate. If you want a highly limited signal, turn the audio gain up so the red LEDs illuminate often.

Adjust Contour

Adjust the Contour knob counterclockwise if your audio source is mostly voice. Adjust the knob clockwise if your audio source is mostly music. The Contour knob adjusts the relative equalization of the unit. This equalization boosts or cuts frequencies above 5 kHz.

Adjust Mix Level

Adjust the mix level until the right VU meter occasionally illuminates the red LED. This is the level adjustment for the combined output from Input 1 and Input 2. If you are using another manufacturer’s receivers with the LT-800/LT-803, determine the frequency of their receivers then refer to Listen’s Frequency Compatibility Tables (pages 14-15) to find the Listen channel that corresponds with the receiver’s frequency. We recommend verifying corresponding channel designations on these tables to ensure compatibility and provide the best possible reception.

The LT-800-216 is Phonak compatible and can be set to display Phonak-specific channels. See page 7 to set Channel Mode and page 13 for specific channel designations.

Listen SQ™ (Super Quiet) – Improving Your Listening Experience

People are accustomed to listening to low-noise, high-fidelity audio (delivered via CD, DVD, etc.). FM radio systems, such as those made by Listen, have more inherent noise compared to most sound systems. To minimize noise, Listen uses a noise reduction technology called Listen SQ™. Both the transmitter and receiver must have the SQ feature enabled to achieve the desired results. SQ is available on new Listen systems, including the LT-800 system. If you are planning to use this product with older Listen systems that do not have Listen SQ, or equipment not manufactured by Listen, you must disable Listen SQ.

Your Listen LT-800 has been shipped to you with the SQ feature enabled.

You may need to disable the SQ function for one or more of the following reasons:

• You are using your new Listen LT-800 with older version Listen receivers that do not have the SQ function.
• You are using your new Listen LT-800 with equipment supplied by other manufacturers (Listen is the only manufacturer using SQ Technology).
• You expect that end users will bring and use their own receivers that don’t have the SQ function.

NOTE : See page 7 to enable or disable SQ (Super Quiet).

Process Mode

Process mode is used for Audio Gain Control (AGC). With the process mode enabled, the LT-800 will automatically adjust for inconsistent signal input levels by raising or lowering the signal level accordingly to provide a consistent sound output level. This feature should be used in applications where a consistent sound level is important and the input levels vary substantially. Typically you would not want to engage the Process when a speaker’s emphasis is critical to the message they are conveying.

Basic and Expanded  Mode (LT-800 only)

In the default Listen channel mode, only the most commonly used channels are available. This is called “Basic Mode”. When the LT-800 is in Basic Mode, “L/O” (lock-out) will be displayed on the LCD, meaning some transmission channels are unavailable.

If the channel needed is not available in Basic Mode, access to all transmission channels is achieved in “Expanded Mode”.

To access Expanded Mode press and hold the channel select “down” button while powering on the unit. To return to Basic Mode, repeat the same process of powering on the unit while holding the “down” button.

SQ Summary

• SQ is NOT squelch
• SQ improves noise performance by at least 20dB
• SQ is NOT compatible with older version Listen products
• SQ is NOT compatible with other manufacturer’s products
• To work properly, SQ must be enabled for both the transmitter and receivers
• SQ can be disabled to permit operation with older
• Listen to products or other manufacturers’ products

RF Reception Maximization Strategies

For proper and dependable operation, Listen receivers need to receive a strong and consistent signal from the originating transmitter. Note that on portable receivers the headset wire is the receiving antenna. The following strategies should be used to maximize this signal:

1. When designing and installing your system, keep in mind that the location of both the transmitting and receiving antennas is critical to maximize broadcast range.
2. Eliminate or minimize obstructions between the transmitting and receiving antenna.
3. Minimize the distance between the transmitting and receiving antennas.
4. Move transmitting and receiving antennas away from metal or conductive objects.
5. Place the transmitting antenna as high as possible.
6. Orient both transmitting and receiving antennas vertically.
7. Position the RF Power switch on the back of the LT-800 to full RF Power, unless lower power is necessary.
8. Keep the coaxial cable from the transmitter to the antenna as short as possible.
   • CAUTION : When installing antennas, ensure the antenna is clear of power lines.

Coaxial Cable

The antenna for the LT-800/LT-803 can be mounted directly on the unit if desired. However, you may find that the unit will provide better performance when the antenna is located elsewhere. If you plan to mount the antenna in a different location other than the top of the unit, you must use cable and connectors rated at 50ohms. Although the cable used for cable TV installations looks similar to this cable, it will not work with your Listen system.

If you need to run cable over a length greater than 50 feet for 216 MHz applications or greater than 100 feet for 72 MHz applications or to maximize broadcast range, Listen recommends that you use RG-8 cable rather than RG-58. RG-8 is a lower-loss cable, meaning that more of your signal will reach the antenna Long cable runs can result in signal degradation due to the “loss” characteristics of the cable. When using RG-58 with a 72 MHz transmitter, there is an average loss of 4 dB per 100 feet of cable, and at 216 MHz using RG-58 an average loss of 8 dB per 100 feet of cable. (A 3dB loss means half of your power has been lost.) However, it is better to suffer coaxial power loss than to try to shoot your signal through obstacles! Obstacles, especially metal, can create drop-outs or reflections of your signal that will result in poor listening conditions.

• NOTE: There are many varieties of 50-ohm, RG-58, and RG-8 cables. You may purchase a cable that is better or worse than this value. Please check with the cable vendor or manufacturer for exact specifications.

Channel Selection

It is important to choose channels that are free from interference to achieve proper operation of your Listen equipment. This process is trial and error. Before turning on the transmitter, listen to the wide band channels on the receivers (lettered channels at 72 MHz and channels that start with a “2” for 216 MHz when using a Listen receiver). Listen to the audio through the headphones or via the speaker and choose a channel with the least amount of interference. Unless you are interfacing with an existing narrowband transmission system, always use a wideband channel.

If you are using multiple channels follow this process:

1. Same Space If you are using multiple transmitters in the same space, the highest number of channels that will work simultaneously is six at 72 MHz and three at 216 MHz. With all of the transmitters off, listen for interference on all the wideband channels with a Listen receiver.   Using the frequency compatibility tables on pages 14-16, eliminate any channels that have noticeable interference. Now choose the channels with the widest channel spacing. It is recommended that adjacent channels be spaced at least 300k Hz apart. If there is no interference the following channels are recommended. For a 72 MHz system, use channels A, C, E, I, J and H. For a 216 MHz system, use channels 2A, 2K, and 2V.

Distributed Spacing

If you are using transmitters that are distributed over a large area, you can achieve more simultaneous broadcast channels. However, it is critical that your receiver(s) be located as close to its transmitter as possible. You can use adjacent channels (see frequency compatibility tables (on pages 14-16) in this case as long as the adjacent channel transmitter is at least 50% further away from the receiver than the original transmitter. Example: The transmitter for thereceiver on channel E is 100 feet from the receiver. The adjacent channel transmitter on channel D should be at least 150 feet away.

It is highly recommended that after channel selection has been achieved, you lock the channel so that it cannot be changed by the user. To accomplish LOCK on the LT-800/LT-803, press the “UP” button for 3 seconds. Repeat the process to unlock.

Notes in regard to using 72 MHz and 216 MHz systems:

1. 72 MHz is a secondary frequency band. This means that other transmitters are licensed to use these frequencies. Thus, you may experience interference from paging transmitters and other types of transmissions. You will need to find a clear channel by listening to all the wideband channels.
2. 216 MHz is a primary frequency band and no other types of transmissions are authorized to use it. Thus, you will find the highest probability of clear channels in this band. However, you may experience intermodulation of the TV Channel 13 aural carrier if there is a Channel 13 transmitter in your area and you are close to the transmitter. If you cannot find a clear channel in 216 MHz band due to channel 13, it is recommended that you switch to a 72 MHz system.

Wide Band

Recommendation Listen recommends that you always use a wide band channel unless you need to be compatible with existing narrowband receivers from other manufacturers. Wide-band channels have lower noise than their narrow-band counterparts.

At 72MHz

The LT-800 at 72 MHz operates on 17 wide band channels and 40 narrow band channels.

• Letters = Wide Band Channels (Example: E)
• Numbers = Narrow Band Channels (Example: 32)

At 216MHz

The LT-800 at 216 MHz operates on 19 wide band channels and 38 narrow band channels.

• “2” as left digit= Wide Band  Channel(Example: 2C)
• “1” and “3” as left digits=
• Narrow Band Channels (Examples: 1A; 3R)

72 MHz Compatibility Chart

Wideband frequencies are indicated in highlighted rows. The highlighted channels also indicated those channels available in the “basic” mode (default). All channels can be accessed when in the “expanded” channel mode for more information) Parenthesis indicate T35 and T20 narrowband.

216 MHz Compatibility Chart

Wideband frequencies are indicated in highlighted rows. The highlighted channels also indicated those channels available in the “basic”  mode (default). All channels can be accessed when inthe “expanded” channel mode (for more information).

Phonak Frequency Chart

Wideband frequencies are indicated in highlighted rows. The highlighted channels also indicated those channels available in the “basic” mode (default). All channels can beaccessed when in the “expanded” channel mode (for more information)

Troubleshooting

The LT-800/LT-803 has no power.

Make sure the LA-207 power supply is connected to a power source and is connected to the jack marked “Power Input”. Make sure the POWER button is pressed in.

There is no audio or the audio level is too low.

Make sure that your audio source is properly connected to Input 1 and/or Input 2. The Input 1 or Input 2 switches must be in the correct position for the appropriate input level. For example: if you are using the output of a mixer on Input 2, the switch should be in the -10dBu position. If it were to be in the +10dBu position, the level would be too low. Also, check the Input knob to ensure it is properly  adjusted. You should be able to see the VU meter deflect on Input 1 or Input 2 corresponding with the input level of the audio source. You can listen to the audio source by connecting a headset to the front panel jack and adjusting the Monitor volume control.
If the level of audio in the transmitter is low and can’t be corrected using the level input switches, the audio processor can be turned on to boost the signal (see page 7 to set, page 11 for the description of Process Mode).

The audio is distorted.

Check to make sure you have the input level select switches in the proper position. You may be providing too much audio level for the input stage to handle. Make sure the SQ mode is set correctly on both the LT-800 and the receivers you are using. If your receivers do not have SQ, make sure the SQ mode is turned off ).

There is a hum in the audio.

Make sure you have properly grounded the audio source to the LT-800/LT-803. Check the connections from the audio source to the LT-800/LT-803. If you can, try to use a balanced audio source – this will reduce the chance of creating a hum. Connect a ground wire from the LT-800/LT-803 to the ground and/or to the ground of the source audio.

There is a tone.

The Test Tone button has been pressed (its LED light is on). Push the Test Tone button to turn off the tone.

The Audio Input 1 sounds “tinny”.

If you are using an unbalanced audio source, make sure Pin 3 on the XLR or the ring on the ¼” plug is grounded ).

I cannot pick up the signal on the receiver.

Check to make sure the receiver and the transmitter are using the same frequency band (i.e. 72 MHz or 216 MHz) and that they are on the same channel. Make sure the LT-800 has an antenna connected. Ensure that the receiver has an antenna (for portable products the headset is the receiving antenna).

I can pick up the signal on the receiver, but it sounds like it’s not tuned in.

Check to make sure the transmitter and receiver are on exactly the same channel. It’s a good idea to lock the channels once they have been set. To lock the LT-800/LT-803, press the UP button for 3 seconds

’m using another brand of receiver – how do I tell which channel to use?

Refer to Listen’s Frequency Compatibility Tables (pages 14-16). Adjust Listen’s transmitter to the same frequency as the other major brand. Since Listen products can access 57 channels, they will most likely receive on the same fixed channel or channels of other major brands. If you are using another brand of receiver, make sure you have turned off the SQ feature on the Listen product(s).

There is not sufficient range.

First, make sure that the receivers you are using are operating properly, then make sure that you have an antenna connected either to the top of the LT-800/LT-803 transmitter or connected to the back of the unit (but not both!). The antenna should be as high as possible and free of obstacles. In addition, make sure you are using the correct antenna type for your unit. You might want to use a remote antenna (provided by Listen) that can be mounted on a mast or wall. Try using different frequencies to find one with less interference.

There is interference in my transmission.

Ensure that the transmitter and receivers are on the same channel. Verify that there are no other transmitters on the same channel or a close channel to the one exhibiting interference. Try different channels until you find a clear channel. If this does not work, try a different frequency band (i.e. if you are using 72 MHz, try 216 MHz or vice versa). Please contact Listen support for assistance and a return authorization (RMA) number to exchange the product for alternate frequency equipment.

End users are adjusting the unit.

First, lock the channel by pressing and holding the channel select UP button for 3 seconds. Consider removing the Input, Mix Level and Contour knobs. You can order a rack mount kit from Listen which offers a security cover that will limit access to the unit.

I am using other manufacturers’ receivers and the sound is distorted.

The receiver is probably not designed to handle the +25 kHz deviation of the Listen transmitter. This can be corrected by turning the Mix Level knob down. Another possibility is that you have enabled the SQ function of the LT-800, and this feature is not available in other companies’ products. You will need to disable SQ in this event

If you are using Phonak receivers, the transmitter is capable of operating in the Phonak mode (please refer.

Several transmitters are operating in the same environment.

For this, you’ll need to choose your transmitting frequencies carefully.  for more details.

Can I have two antennas connected to my transmitter?

No. The LT-800/LT-803 transmitter can use only one antenna connection at a time. You may connect either a top-mount antenna through the top antenna port, or a remote antenna connected to the BNC connection on the rear of the unit. If multiple antennae are simultaneously connected to both ports the transmitter will have extremely poor broadcast performance and range.

Compliance Notice & FCC Statement

LT-800/803 Compliance Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) These devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesirable operation

Listen’s LT-800 Transmitter (216 MHz only)

Listen’s LT-800 transmitter is authorized by rule under the Low Power Radio Service (47 C.F.R. Part 95) and must not cause harmful interference to TV reception or United States Navy SPASUR installations. You do not need an FCC license to operate these transmitters. These transmitters may only be used to provide: auditory assistance to persons with disabilities, persons who require language translation, or persons in educational settings; health care services to the ill; law enforcement tracking services under agreement with a law enforcement agency; or automated maritime telecommunications system (AMTS) network control communications. Two-way voice communications and all other types of uses not mentioned above are expressly prohibited.

This device must be installed by a trained audio professional or certified dealer of Listen. The user can’t make any modifications to the unit without the expressed written consent of Listen Technologies Corporation. Any modifications made will void the FCC compliance, Listen warranty, and the user’s authority to operate Listen’s equipment

LT-800/803 FCC Statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If  this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC and IC Rules. In order to maintain compliance with FCC and IC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.

Industry Canada Statement

• LT-800/803 Industry Canada Statement

This device complies with ISED Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with FCC and IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body

Warranty & Contacting Listen

Warranty

Listen Technologies products are designed and engineered to provide long- standing use for many years. Listen Technologies warrants all products against defects in materials and workmanship. All product warranties can be transferred, in the event the product is transferred the warranty is valid from the original date of the product purchase.

Listen shall bear no responsibility or obligation with respect to the manner of use of any equipment sold. Listen specifically disclaims and negates any warranty of merchantability or fitness of use of such equipment including, without limitation, any warranty that the use of such equipment for any purpose will comply with applicable laws and regulations. The terms of the warranty are governed by the laws of the state of Utah, USA. The warranty does not include normal wear and tear on the product. In addition, Listen Technologies is not liable for consequential damages due to any failure of equipment to perform as intended.

Listen stands by the quality of its manufactured products and will, at its own discretion, repair or replace any defective products. All product warranties are subject to change without notice. For product-specific warranty information visit, https://www.listentech.com/support/warranty/

Contacting Listen

If technical service is needed, please contact Listen. Pre-authorization is required before returning Listen products. If products were damaged in shipment, please contact the carrier, then contact Listen for replacementor repair requirements payable by the carrier.

14912 Heritage Crest Way

• Bluffdale, Utah 84065-4818
• +1.801.233.8992
• 1.800.330.0891 Toll-Free (USA & Canada)
• +1.801.233.8995 fax
• support@listentech.com
•   www.listentech.com

Accessories

Rack Mount Accessories

• NOTE : Rack-mounted units cannot use the LA-106, LA-102 or LA-101 top-mounted antenna.

LISTEN TECHNOLOGIES 14912 Heritage Crest Way, Bluffdale, Utah 84065-4818 USA

• Phone: +1.801.233.8992
• Toll-Free: 1.800.330.0891
• www.listentech.com

Copyright © 1998 – 2023 Listen Technologies Corporation®. All rights reserved. 20231115.

References

• ch.com
• Home - Listen Technologies
• Hearing Aids and Solutions | Phonak
• Warranty - Listen Technologies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>