POBOMVOM JY-JMT037 Automatic Chicken Coop Door Solar Powered Instruction Manual

SOLAR POWERED
CHICKEN HOUSE DOOR

BASIC INSTRUCTIONS FOR SOLAR POWERED CHICKEN COOP DOOR

INSTALLATION METHOD OF SOLAR POWERED CHICKEN HOUSE DOOR

Suggested door opening size, width 9.2xH, height 10W inches 234 * 25.4cm
| For horizontal installation, use the attached screw to fix the product according to the position shown in the red circle and complete the installation.
|
Minimum 11 inches above the installation position without obstruction| Press the power button on the remote control to wake up

PART OF ACCESSORIES FOR SOLAR POWERED CHICKEN COOP DOOR

BASIC BUTTON DISPLAY INSTRUCTIONS

1. Flashes when the chicken coop door opens and rises , flashes when the chicken coop door closes and falls , and does not display an icon after completion.
2. The anti pinch protection is enabled by default. In the working mode setting, the anti pinch protection can be disabled by canceling/enabling. After cancellation the four dots do not display to indicate closure. When the anti pinch protection is triggered it flashes, and the door automatically rises for 20 seconds. The rear door automatically descends.
3. After selecting the working mode, the icon flashes, and click OK to enter the working mode setting.
4. The icon remains illuminated during solar charging.
5. The icon displays the closed status of the chicken coop door, while the icon displays the open status of the door.
6. Display when the battery is fully charged, and when the battery is low. Please charge in a timely manner.
7. When turned on, is used as the confirm key and to return to the homepage.

BASIC PARAMETERS

OPERATING STEPS

1. Press and hold for 3 seconds to turn on the device.

2. The following operations can be performed during startup:
   (1) Press Manually open and close the chicken coop door.
   (2) Press You can set the working mode of the chicken coop door and follow the prompts on the screen.
   (3) When turned on Click the button to save the set parameters and return to the homepage.
   (4) Long press without setting parameters Shut down in 3 seconds.

3. If no operation is performed within 1 minute, the chicken coop door will automatically enter standby mode and the screen will also turn off.

4. When the chicken coop door is in standby mode, it can be awakened by the following operations:
   (1) Click The remote control button wakes up the chicken coop door and the screen lights up.
   (2) Click on the panel Wake up the chicken coop door and the screen lights up.

MODE PARAMETER SETTINGS

Prompt: Parameter warning operation in T-T/L-L modes:

When the opening/closing time of T-T mode is set to be the same, or when the door closing light level of L-L mode is set to ≥ the door opening light level, flashes and cannot save the settings to return to the main interface. After setting reasonable parameters, click the button to save and return to the main interface.

T-T (timed door opening timed door closing) mode

| 1. Click the button to enter the mode selection interface.
2. Click the ****key to select the desired mode to be set. (The icon will flash)
3. Click to enter mode settings.
---|---
| Current time setting:
Click to adjust the time, click to save and proceed to the next item.
| 【T-T MODE】
Set the opening and closing times,click to save and proceed to the next item.
| After setting the door opening and closing
parameters, you can click the  button to turn on/off the anti pinch protection function
when entering this page.
| After setting up, click the key to return to the main interface.

L-L (Light Door Open Light Door Close) mode

| 1. Click the button to enter the mode selection interface.
2. Click the key to select the desired mode to be set. (The icon will flash)
3. Click to enter mode settings.
---|---
| current time setting:
Click to adjust the time, click to save and proceed to the next item.
| 【L-L MODE】
Set the light sensitivity level for opening and closing doors, click to save and proceed
to the next item.
| After setting the door opening and closing parameters, you can click the button to
turn on/off the anti pinch protection function when entering this page.
| After setting up, click the key to return to the main interface.

T-L (timed door opening light door closing) mode

| 1. Click the button to enter the mode selection interface.
2. Click the key to select the desired mode to be set. (The icon will flash)
3. Click to enter mode settings.
---|---
| Current time setting:
Click to adjust the time, click to save and proceed to the next item.
| 【T-L MODE】
Set the door opening time and door closing light level, click to save and proceed to the
next item.
| After setting the door opening and closing parameters, you can click the button to
turn on/off the anti pinch protection function when entering this page.
| After setting up, click the key to return to the main interface.

L-T (light opening timed closing) mode

| 1. Click the button to enter the mode selection interface.
2. Click the key to select the desired mode to be set. (The icon will flash)
3. Click to enter mode settings.
---|---
| Current time setting:
Click to adjust the time, click to save and proceed to the next item.
| 【L-T MODE】
Set the light sensitivity level and closing time for opening the door, click to save and
proceed to the next item.
| After setting the door opening and closing parameters, you can click the button to turn on/off the anti pinch protection function when entering this page.
| After setting the door opening and closing parameters, you can click the button to turn on/off the anti pinch protection function when entering this page.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>