Lumox xCube4-NA Full Spectrum LED Grow Lights User Manual
- May 15, 2024
- Lumox
Table of Contents
**Lumox xCube4-NA Full Spectrum LED Grow Lights User Manual
**
Before using the product, please read this carefully.
Product Introduction
Explanation of Network Indicator Light Status:
- Fast blinking blue light: Wi-Fi EZ mode, waiting for network configuration.
- Slow blinking blue light: Hotspot mode, waiting for network configuration.
- Steady blue light: Network connected.
- Blue light off: Network disconnected.
Explanation of Network Configuration Button:
- When the network indicator light is blinking, long-pressing for 5 seconds will switch the network configuration mode.
- When the network indicator light is steady on or off, long-pressing for 5 seconds will reset the network configuration, and you will need to perform the network setup process again
Important Disclaimer: This product is a precision electronic device. Please do not use it in environments where water exposure is possible. If the product is used in a way that causes malfunction, any resulting issues with product usage, or safety concerns, our company will not be held responsible.
Warning
This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However.
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE:
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, this equipment
should be installed and operated with minimum distance of 20cmthe radiator
your body. This device and its antenna(s) must not be colocated or operation
in conjunction with any other antenna nr transmitter.
Basic Parameters
-
Product Name: Lumo-X xCube4
-
Product Model: xCube4-NA
-
Specificatons:
1800W，15A MAX，120V
2200W，10A MAX，220V -
Port Output:
1200W，10A MAX，120V
2200W，10A MAX，220V -
Operating Temp: 0℃ to 40℃
-
Supported Systems: Android5.0 or iOS13.0 or higher
-
Wireless Connection: Wi-Fi IEEE 802.11 b/g/n 2.4GHz
Manufacturer: Canbridge Tech Ltd.
Service Email: Service@Lumo-X.com
Service Website: www.Lumo-X.com
Quick Setup
This product requires an internet connection and can be controlled through the “Lumo-X” app, which supports Android and iOS systems. It can be paired with various Lumo-X environmental sensors and, in combination with backend automatic/timed strategies, can control peripherals such as fans, heaters, and other devices.
-
Power On
Connect the power cord to the main unit’s power outlet. Plug the power cord into the power source, then turn on the overload protection switch.
When the overload protection switch indicator light is illuminated, that the main unit is powered on. -
Download the App
Method 1: Search for “Lumo-X” on Google Play or the App Store and install the App.
Method 2: Scan the QR code to download and install the Lumo-X App.
-
Register/Login Account
To register, use your email to create an account. After successfully registering, you can log in using either your username or email address. -
Create a Grow Room
Once you’ve successfully logged in, navigate to the App’s main page. Click on the “Weather” tab, and press the “ADD A ROOM” button. Input the room’s name and information, then click “NEXT” to create a Grow Room.
-
Connect xCube
On the App’s main page, click on the “Weather” tab. At the top of the page, click “Add a Socket” to initiate the network configuration process. Ensure that your phone is connected to a 2.4GHz Wi-Fi network and that the xCube’s network configuration indicator light is blinking blue. Follow the app’s instructions to proceed. Once successfully connected, the xCube’s network configuration indicator light will remain steady blue.
-
Connect Lumo-X Environmental Sensors
Refer to the product introduction to connect the appropriate Lumo-X environmental sensor. In the app, you can view real-time sensor data to monitor the environment.
More Information
For more information and other great products, please visit the following link
or scan the QR code.
Website: https://www.Lumo-X.com
xCommunity: https://community.Lumo-X.com
Instagram: https://www.instagram.com/lumoxgrow
Website
xCommunity
**Instagram
**
Documents / Resources
|
Lumox xCube4-NA Full Spectrum LED Grow
Lights
[pdf] User Manual
xCube4-NA Full Spectrum LED Grow Lights, xCube4-NA, Full Spectrum LED Grow
Lights, Spectrum LED Grow Lights, LED Grow Lights, Grow Lights, Lights
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>