hama 00223544 Battery Tester Universal Instruction Manual

hama 00223544 Battery Tester Universal

Product Information

Specifications

• LCD display
• Battery Types: US AAA, AA, C, D, N, E, CR 123A, CR 2, 2 CR 5, CR-P2, CRV3
• 3V Lithium Buttoncells
• 1.5V Buttoncells
• Germany Mikro Mignon Baby Mono Lady 9V Block
• Operating Voltage: Max. 1.5V, 9.0V, 3.0V, 6.0V

Package Contents

The package includes the following:

• The measuring device
• User manual/instructions

Safety Instructions

Please follow these safety instructions:

• Do not touch uninsulated product parts that may carry hazardous voltage to avoid electric shock.
• Pay attention to warning symbols and notes.

Operation

To operate the device:

1. Remove the battery compartment cover on the back.
2. Insert an AAA battery, observing the correct polarity.
3. The measuring device is then immediately ready for use.

Display

The LCD display shows the following information:

• I—-1 to 5—-I: Batteries are empty and need to be replaced.
• Rechargeable batteries are already fully discharged and need to be charged immediately. Discharging rechargeable batteries down to this field should be avoided.
• I—————I—– 6 to 11——-I: Batteries have weak energy remaining and can only be used to a limited extent in low current requirement devices (e.g., clocks).
• Rechargeable batteries have reached the recharging point and should be charged as soon as possible. I—————I——————–l——-12 to 18——-I:
• Batteries are OK with sufficient stored energy. Rechargeable batteries only reach 13/14 bars at full charge due to lower cell voltages.
• If the display falls quickly, the battery/rechargeable battery is faulty and should not be used anymore, as it has a high internal resistance during measurement.

Care and Maintenance

To ensure proper care and maintenance:

• Disconnect the device from the mains before cleaning and during prolonged periods of non-use.

Measurements

Follow these steps for measurements:

1. Only test one battery/rechargeable battery at a time.
2. Select the testing field according to the size of the battery or use the appropriate shapes of the housing. The corresponding designations of the batteries are imprinted into the housing.
3. Insert button cells with the positive pole facing upwards.
4. Ensure correct polarity and secure contact. Do not position batteries at an angle. Button cells must lie on the lateral measuring contact.
5. The LCD bar display shows the test object’s residual voltage.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe the operating instructions and/or safety notes.

Frequently Asked Questions (FAQ)

Q: Can I test multiple batteries at once?

• A: No, only test one battery/rechargeable battery at a time.

Q: How should I position the button cells for testing?

• A: Insert button cells with the positive pole facing upwards. Ensure they lie on the lateral measuring contact.

Technical specification

21 mm

| 3,0 V
1.5 V Buttoncells| 1.5 V Knopfzellen| Ø max.

12 mm

| 1,5 V

Operating instruction

• Thank you for choosing this Hama product!
• Take your time and read the following instructions and information completely.
• Please keep these instructions in asafe place for futurereference.

Explanation of warning symbols and notes

Risk of electricshock

• This symbol indicates arisk of electric shock from touching uninsulated product parts that may carry hazardous voltage.

Warning

• This symbol is used to indicate safety instructions or to draw your attention to specifichazards and risks.

Note

• This symbol is used to indicate additional information or important notes.

Package contents

• Rechargeable battery / battery tester
• 1x AAA micro battery
• These operating instructions

Safety instructions

• The product is intended for private, non-commercial use only.
• Protect the product from dirt, moisture and overheating and use it in dry rooms only.
• Do not drop the product and do not expose it to any major shocks.
• Do not operate the product outside the power limits given in the specifications.
• Do not modify the device in any way. Doing so voids the warranty.
• Dispose of packaging material immediately in accordance with the locally applicable regulations.
• Use the product only for the intended purpose.
• Do not use the product in a damp environment and avoid splashing water.
• Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
• Do not use the product in areas in which electronic products are not permitted.
• Only use the article under moderate climatic conditions.
• Do not open the device or continue to operate it if it becomes damaged.
• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
• Do not short-circuit charger / power supply unit contacts!
• This device may be used by children who are aged 8 or older and people with impaired physical, sensory or mental abilities, or those who lack experience and knowledge, if they are supervised or have been trained in safe use of the device and have understood the associated dangers. Children are not permitted to play with the device. Children may not clean the product or perform user maintenance without supervision.

Risk of electric shock

• Do not open the device or continue to operate it if it becomes damaged.
• Do not use the product if the AC adapter, the adapter cable or the mains cable are damaged.
• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.

Warning

• Only operate the product from an approved socket that is connected to the public power supply. The socket must be installed close to the product and must be easily accessible.
• Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
• If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
• If you will not be using the product for a prolonged period, disconnect it from mains power.

Operation

Warning

• When inserting batteries, note the correct polarity (+ and – markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the specified type.
• Before you insert the batteries, clean the battery contacts and the polarity contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries, or batteries of different types or from different manufacturers.
• Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not burn batteries.
• Keep batteries out of the reach of children.
• Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
• Remove spent batteries from the product and dispose of them without delay.
• Avoid storing, charging and using in extreme temperatures and at extremely low atmospheric pressures (such as at high altitudes).
• Remove the battery compartment cover on the back and insert an AAA battery, observing the correct polarity. The measuring device is then immediately ready for use.

Measurements

Only one battery / rechargeable battery should be tested at a time. Its residual voltage is shown via the LCD display.

1. Select the testing field according to the size of the battery or use the appropriate shapes of the housing. The corresponding designations of the batteries are imprinted into the housing. Insert button cells with the positive pole facing upwards.
2. Observe the correct polarity and secure contact. Do not position batteries at an angle. Button cells must lie on the lateral measuring contact.
3. The LCD bar display shows the test object’s residual voltage.

Display

• I—-1 to 5—-I
• Batteries: Empty – replace
• Rechargeable batteries: Already fully discharged charge immediately. Discharging of rechargeable batteries down to this field should be avoided.
• I—————I—– 6 to 11——-I
• Batteries: Weak, little remaining energy, can only be used to a limited extent in consumers with low current requirements, e.g. clocks, etc.
• Rechargeable batteries: Recharging point reached – charge as soon as possible I—————I——————–l——-12 to 18——-I
• Batteries: OK, stored energy sufficient
• Rechargeable batteries: Due to lower cell voltages, rechargeable batteries only reach 13/14 bars at full charge.
• Display falls quickly: Battery / rechargeable battery faulty and should no longer be used, e.g. high internal resistance during measurement.
• Do not use flat or damaged cells any further. After measurement is finished, remove the test object from the device – do not carry out any long-term measurements.

Care and maintenance

Note

1. Disconnect the device from the mains before cleaning and during prolonged periods of non-use.
2. Only clean this product using a lint-free, slightly damp cloth and do not use any harsh cleaners.
3. Ensure that no water is able to enter the product.

Warranty disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

• Hama GmbH & Co KG 86652 Monheim/Germany
• Service & Support
• www.hama.com
• +49 9091 502-0
• All listed brands are trademarks of the corresponding companies.
• Errors and omissions excepted, and subject to technical changes.
• Our general terms of delivery and payment are applied.

References

• hama.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>