GE APPLIANCES HTX26EASWWW Electric Dryer Instruction Manual

GE APPLIANCES HTX26EASWWW Electric Dryer

Product Information

Specifications

• Model: HTX26EASWWW
• Dryer Dimensions (in inches): 22 3/8 (W) x 26 5/8 (D) x 37 1/2 (H)
• Exhaust Options: 4-way via rear, right, left, and bottom
• Electric Dryer Rating:
  • 240V, 5600W, 60Hz, 24 Amp
  • 208V, 4400W, 60Hz, 22 Amp
• Circuit Requirements: 30-amp circuit breaker or time-delay fuse

Installation Instructions
Special Installation Requirements:

• Alcove or Closet Installation:
  • Dryer must be exhausted to the outside.
  • Minimum clearances: 0 on either side, 1 front, top, and rear.
  • Closet doors must be louvered or ventilated with minimum open area requirements.
• Bathroom or Bedroom Installation:
  • Dryer must be exhausted outdoors.
  • Installation must comply with local codes or National Electric Code and National Fuel Gas Code.
• Minimum Clearances Other Than Alcove or Closet Installation:
  • Minimum clearances to combustible surfaces: 0 on both sides, 1 rear.

Power Cords
GE strongly recommends the use of factory-specified power cords. Select the appropriate power cord based on your installation requirements.

*Order online at GEApplianceparts.com or by phone at 877.959.8688.

Accessories
List of accessories available for purchase separately. Ensure to calculate the total vent system length when adding accessories to the dryer. Exhaust Length Calculation
Dryers MUST be exhausted to the outside. When calculating the total vent system length, add all straight portions and elbows of the system. Frequently Asked Questions (FAQ)

• Q: Can I install the dryer in a closet?
  A: If approved for alcove or closet installation, ensure proper ventilation and meet minimum clearance requirements.

DRYER DIMENSIONS

• EXHAUST OPTIONS: 4-way via rear, right, left and bottom.
• CIRCUIT REQUIREMENTS: An individual, properly grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.
• ELECTRIC DRYER RATING: 240V, 5600W, 60Hz, 24 Amp, 208V, 4400W, 60Hz, 22 Amp
• INSTALLATION INFORMATION: For complete information, see installation instructions packed with product for current dimensional data.

SPECIAL INSTALLATION REQUIREMENTS

ALCOVE OR CLOSET INSTALLATION:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between the dryer cabinet and adjacent walls or other surfaces are: 0″ either side, 1″ front, top and rear.
• Closet doors must be louvred or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

BATHROOM OR BEDROOM INSTALLATION:

• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
Minimum clearances to combustible surfaces: 0″ on both sides, 1″ rear.

POWER CORDS: GE Appliances strongly recommends the use of factory- specified parts. Select the power cord to fit your installaton requirements.*
NOTE: If the dryer circuit is on a circuit protected by a GFCI breaker, then the 3-wire installation is not permitted. Hose wiring and dryer must be configured for 4-wire.

For complete information, see installation instructions packed with your dryer.

DUCTING MATERIALS:
For best performance, this dryer should be vented with 4″ diameter all-rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil- type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see the installation instructions packed with your dryer for complete instructions when using flexible metal (foil-type) ducting.

EXHAUST LENGTH CALCULATION:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4′ rigid (aluminium or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers MUST be exhausted to the outside.

CAUTION: For personal safety, do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a pampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.

ACCESSORIES

FEATURES AND BENEFITS

• AutoDry – AutoDry monitors the internal air temperature to determine the ideal drying time, protecting your garments from overdrying.
• Powerful Venting & Flexible Installation – Powerful airflow offers long-lasting performance from lint build-up and offers venting solutions up to 120 feet for greater installation flexibility.
• Large Diffuser for Even Drying – A large internal heat diffuser allows for warm air to evenly spread throughout your clothes during the cycle, making this the ideal dryer for large loads and bulky items.
• Durable Aluminized Drum – This durable, long-lasting design resists corrosion and optimizes drying performance.
• Reversible Dryer Door – Door can swing from either direction, making it easier to access the last sock from the back of the drum.
• Shallow Depth Design – Reaching into your dryer is easier than ever thanks to the shallow depth design, which also fits into more spaces without sacrificing capacity.
• Up-Front Lint Filter – Simplify the task of lint removal with our convenient upfront lint filter, enhancing airflow within the appliance and for your garments.

COMPATIBLE WASHER: HTW265ASWWW – Hotpoint® 4.0 cu. ft. Capacity Washer with Stainless Steel Basket, Cold Plus and Water Level Control.

*Order online at GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours.
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, at 800.626.2000.

References

• Appliance Parts, Accessories & Water Filters | GE Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>