GE APPLIANCES GTD48EASWWB Electric Dryer Instruction Manual
- May 15, 2024
- GE Appliances
Table of Contents
GE APPLIANCES GTD48EASWWB Electric Dryer Instruction Manual
EXHAUST OPTION: 4-way rear, right, left and bottom.
CIRCUIT REQUIREMENTS: An individual, properly-grounded branch circuit,
protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36″ of service cord entry
and accessible when dryer is mounted in position.
INSTALLATION INFORMATION: For complete information, see installation
instructions packed with your dryer.
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
-If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
– The dryer MUST be exhausted to the outside.
– Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0″ either side; 1″ front, top and rear.
– Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet
contains both a washer and a dryer, doors must contain a minimum of 120 sq.
in. of open area equally distributed.
– No other fuel-burning appliance shall be installed in the same closet with a
gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
– The dryer MUST be exhausted to the outdoors.
– The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code, ANSI
Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
– Minimum clearances to combustible surfaces are: 0″ both sides; 1″ rear.
DRYER EXHAUSTING INFORMATION: Use metal duct only, vertical and
horizontal ducting.
POWER CORDS:
GE Appliances strongly recommends the use of factory specified parts. Select
the power cord to fit your installation requirements.*
NOTE: If the dryer circuit is on a circuit protected by a GFCI breaker,
then 3-wire installation is not permitted. Hose wiring and dryer must be
configured for 4-wire.
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4″ diameter all-rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil- type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil-type) ducting.
EXHAUST LENGTH CALCULATION:
- Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
- The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety, do not terminate exhaust into a chimney,
under any enclosed house floor (crawl space), or into an attic, since the
accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back
drafts, bird nesting, etc. The wall cap must also be located at least 12″
above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.
DRYER EXHAUSTING INFORMATION– USE METAL DUCT ONLY VERTICAL AND HORIZONTAL DUCTING BEST PERFORMANCE
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all the straight
portions and elbows of the system (including the transition duct.)
Order online at GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours. For answers to your Monogram, CaféTM, GE ProfileTM or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Note that this is a contract exclusive model
FEATURES AND BENEFITS
Auto Dry – Auto Dry monitors the internal air temperature to determine the
ideal drying time, protecting your garments from overdyeing.
Powerful Venting & Flexible Installation – Powerful airflow offers long-
lasting performance from lint build-up and offers venting solutions up to 120
feet for greater installation flexibility.
Large Diffuser for Even Drying – A large internal heat diffuser allows for
warm air to evenly spread throughout your clothes during the cycle, making
this the ideal dryer for large loads and bulky items.
Extended Tumble – Tumble clothes without heat to prevent creasing and
wrinkling with a convenient extended tumble button. This cycle is ideal to
help to remove even more pet hair on already dry items, allowing debris to be
caught by your dryer’s lint screen.
Interior Light – Convenient dryer drum lights provide better visibility to
help ensure no small items or socks are left behind, making it easier to load
and unload laundry.
Adjustable Cycle Signal – End of Cycle signal volume is adjustable, ensuring
you are alerted to promptly remove your garments before winkles have a chance
to form.
Durable Aluminized Drum – This durable, long-lasting design resists corrosion
and optimizes drying performance.
Reversible Dryer Door – Door can swing from either direction making it easier
to access the last sock from the back of the drum.
Temperature Selection – Offers a range of drying temperatures to adjust to the
specific needs of your garments for personalized garment care.
Up-Front Lint Filter – Simplify the task of lint removal with our convenient
up-front lint filter, enhancing airflow within the appliance and for your
garments.
Delicates Cycle – This delicate, low-heat dryer setting helps protect fabrics
and extends the lifetime of even your most delicate items
MATCHING WASHERS: GTW480ASWWB GE® 4.6 cu. ft. Capacity Washer with Stainless
Steel Basket, Impeller,
Cold Plus and Wash Boost GTW485ASWWB GE® 4.5 cu. ft. Capacity Washer with
Stainless Steel Basket, Agitator,
Cold Plus and Wash Boost
ACCESSORIES*
*Order online at GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours.
Specification Revised 02/24
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>