SECURAM SS02 Single Pole Smart Light Switch Installation Guide
- May 15, 2024
- SecuRAM
Table of Contents
WI-FI SMART SWITCH
INSTALLATION GUIDE
SH-5502
SS02 Single Pole Smart Light Switch
Thank you for purchasing your SECURAM smart home product. Our innovative products are designed to make your home safer, more convenient, and more energy-efficient. With the help of our easy-to-use app, you can control all of your SECURAM smart home devices from anywhere, at any time. Let’s get started!
WARNING: RISK OF ELECTRIC SHOCK OR FIRE.
Please follow all safety instructions on page two (2) and thirteen (13) before
installing, servicing, of removing your Switeh.
If you’re not femilir with basic electrical work, we recommend calling a
professional electrician for installation.
What’s in the Box
- Wi-Fi Smart Switch
- Faceplate
- 25crews
- Wire Labels
- Installation Guide
Getting started
-
Tum OFF power supply at the circuit breaker or fuse.
Use a noncontact voltage tester to ensure that power is off. More than one disconnect switch may be needed to turn off power. -
Make sure the existing box has a neutral wire.
Switch Overview
Install
STEP1
Shut off power at the circuit breaker for the switch you are replacing. More
than one disconnect switch may be required to turn off power. Use a noncontact
voltage tester to ensure power is off
STEP2
Make sure the existing switch box has a neutral
*wire.* Remove existing wall plate.
Neutral wire is typically white.
STEP3
Turn on power at the circuit breaker and use a noncontact Voltage tester to
check which wire is live (iine). The tester will flash or chirp when it comes
close to a line wire. Turn off the power at the circuit breaker and label the
wires.
Remove old switch by disconnecting all wires.
STEP4
Follow the wiring diagram to connect the wires in the wall box to the switch.
Insert the wire into the connector hole of the switch, and use the screwdriver
to fasten it firmly. Or you can connect the switch wires to the wires in the
wall box with the wire nuts.
5 Install, cont,
STEP5
Use screws to secure Switch into your wall.
Then, snap on included faceplate.
STEP6
Restore power by tuming on the breaker.
STEP7
Once power is connected, the LED indicator will blink blue toindicate it is
ready to connect to Wi
Download the SECURAM Guard app
|
---|---
https://apps.apple.com/us/app/securam-guard/id1541193113|
https://play.google.com/store/apps/details?id=com.smarthomeapp.android&hl
Register SECURAM Guard account
STEP 1
Enter your emal address or mobile phone number.
STEP 2
Enter the verification code.
STEP 3
Create a password.
STEP 4
Log into the app.
Pairing Your Switch
STEP 1
Loginto the app.
STEP 2
Tap + to add your device.
STEP 3
Select Security Switch.
STEP 4
Follow the step-by-step in app guide.
LED Indicator Status
| LED Indicator | Switch Status |
|---|---|
| Blinking Blue | Device in pairing mode |
| Blinking Red | Device network disconnected |
| Blinking Orange | Home Security System is armed |
| Solid White | Device working normally |
| Off | Switch has no power |
Button Operation
ON/OFF
This button toggles the wired light on and off.
R eset Button
To reboot switch: Press the button once.
To factory reset: Press and hold unti all LEDS turn on. The LED indicator will
begin to blink biue, indicating the switch has been reset.
Warnings
- Install only in a suitable UL Listed outlet box
- CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing.
- Tighten terminal screws to 13 Ibf-in / 7.5kgf-c.
- Supported specified line number for the thread terminal copper wire: 12AWG and 14AWG,
Requirements
- Neutral Wire
- Single Pole with >2 deep box
- 2.4GHz Wi-Fi network (5GHz Wi-Fi is not supported)
- SECURAM Guard App
- Phone with 105 9.0 or later, or Android 8.0 or later
Specifications
- Rating: 100-120VAC 60Hz 600W Incandescent
- Supported Load Types:
- 100-120V~ 5A, Incandescent
- 100-120V~ 5A, Electronic Fluorescent Ballast
- 100-120V~ 3, LED
- Wireless Frequency: 2.4 GHz
- Wireless Standard: IEEEB02.11 blg/n
- Operating Temperature: 32°F-104°F (0 °C-40 °C)
- Operating Humidity: 5%-85%RH, Non-condensing
- Size: 2,91 169″ x 4.69″ (L¥WxH)
- Container FCCID: 2ACZ7-ESP32WROOM32E
Children Safety
This device and ts accessories may contain smal parts.
Please keep them out of reach of children.
Remember, this device is not a toy. Chidren should only use it under adult
supervision
Be sure to keep it away from children and pets.
FCC Notice
This device complies with part 15 o the FCC Rules. Operation is subject 10 the
following two conditions: (1) this dovice may not cause harmiul interference,
and (2) this device must accept any inerference recaived, ncluding
interference that may cause undesired operation. Any changes or modificalions
not exprassiy approved by he party responsibie for compliance could void the
user’s authority to operate. the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These lmits
re designed to provide reasonable protection against harmiul intarference in a
resigential nstalaton. This equipment generates, uses and can radiate racio
frequency energy and, f not installed and used in accardance with the
fnstructions, may Cause Rarmil interfarance t radlo communications. However,
hera s no ‘guarantee that interference wil not occur in 3 partcular
instalaton. ifthis ecuipment does cause harmiul nterference to racio or
television reception, which can be determined by turning the equipment off and
on the user s encouraged to try to correct the nterference by one or mre of
the following measures
- Reorient or relocate the receiving antenna
- Increase the separation batwean te equipment and receiver.
- Comnect the equipment nto an outiet o cicuit different from that 10 Which the receiver s conneeted:
- Consult the dealer or an experienced radio/TV technician for help.
The device has be requirements. The device can be used in portable exposure condition without restricton, Contains FGC ID: 2ACZ7-ESP32WROOM2E evaluated to meet general RF exposure
We are here to help.
Contact us if you have any questions, or need assistance with our products.
http://support.securamsys.com
support.securamsys.com
+1(805) 988-8088