BLUSTREAM HEX11WP-TX Wall Plate Transmitter User Guide
- June 4, 2024
- BLUSTREAM
Table of Contents
HEX11WP-TX
QUICK REFERENCE GUIDE
Introduction
Our HEX11WP HDMI Wall Plate HDBaseT™ Transmitter is a 4K solution that extends HDMI up to 70m at 1080p (40m at 4K 60Hz 4:2:0). The HEX11WP-TX has been designed to work with all Blustream HDBaseT™ receiver and matrix solutions, be installed in both UK and European backboxes and can be powered locally or from compatible Blustream HDBaseT™ products.
FEATURES:
- Advanced HDBaseT™ technology offers the distribution of video and audio over a single CAT cable
- Supports 4K UHD video up to 40m (3840 x 2160 @30Hz 4:4:4, 4096 x 2160 @24Hz 4:4:4, and 4K @60Hz 4:2:0)
- Extends HDMI at 1080p up to a distance of 70m
- Smart EDID function automatically limits EDID to within HDBaseT™ specification to improve compatibility#
- Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus, and DTS-HD Master Audio transmission
- Supports 12V-48V PoC from compatible Blustream HDBaseT™ receiver / matrix products
- Bi-directional RS-232 pass-through
- Supports IR pass-through to HDBaseT™ device
- Compatible with all Blustream HDBaseT™ receiver/matrix products*
- Magnetic faceplate surround allowing both UK & EU backbox compatibility
- HDCP 2.2 support
*Technical performance is subject to the features supported on the connected HDBaseT™ device.EDID function added to products from Revision B onward.
Front Panel Description
-
Power Status Indicator – Illuminates when powered
-
HDBaseT™ Link Status Indicator – Illuminates when the transmitter is connected to an HDBaseT™ receiver/matrix product successfully
-
EDID Selection Button – Cycle through 2 EDID modes – see EDID Management below
-
IR Receiver – Built-in IR sensor for IR pass-through
-
HDMI Input – Type A HDMI port to connect HDMI source
Rear Panel Description
-
HDBaseT™ Output – RJ45 HDBaseT ™ port to connect to the HDBaseT ™ input port of the compatible Blustream HDBaseT ™ receiver/matrix device
-
12V DC Input – 2-pin Phoenix connector to connect to Blustream 12V power supply (supplied) Product supports PoC to Blustream HDBaseT™ Receiver products. PoC output is not live until the HDMI source is connected to the wall plate. This feature can be used for 12V triggers on Blustream SW41HDBT Switcher.
-
IR Receiver Input – 3-pin Phoenix connector to connect to Blustream IR receiver (not supplied)
-
RS-232 – 3-pin Phoenix connector for RS-232 pass-through to/from compatible Blustream HDBaseT™ device
Note: When powering the HEX11WP-TX locally and using PoC to power a compatible Blustream receiver device, power is only enabled when an active HDMI source device is connected to the HEX11WP-TX. This feature is used to trigger auto-switching on the Blustream SW41HDBT HDBaseT™ Switcher. Products from Revision B onward.
EDID Management
The HEX11WP-TX features automatic EDID management to ensure signals being
transmitted fall within the 10.2Gbps bandwidth requirement of HDBaseT™. The
HEX11WP-TX will evaluate the EDID of the display device and modify its EDID
value to ensure compatibility. The default maximum resolution supported is 4K
@60Hz 4:2:0. By pressing the EDID selection button you can limit the maximum
EDID to 4K @30Hz 4:4:4.
Note: Products from Revision B onward.
Infrared Receiver
The HEX11WP-TX features 2 x options for receiving IR signals. The HEX11PW-TX
has an in-built IR receiver on the front panel that will receive IR commands
from line-of-sight IR remote controls, and a 3-pin Phoenix connection on the
rear panel. You may need to cut and terminate the Blustream IR receiver (not
supplied) into the Phoenix connector.
The pin-out configuration for the Blustream IR receiver is as follows:
- White – 5V
- Red – Signal
- Black – Ground
Specifications
HEX11WP-TX
Video Input Connectors: 1 x HDMI Type A, 19-pin, female
Video Output Connectors: 1 x HDBaseT™ RJ45 connector
RS-232 Serial Port: 1 x 3-pin Phoenix connector
IR Input Port: 1 x 3-pin Phoenix connector
Local Power Input: 1 x 2-pin Phoenix connector
Module Dimensions (W x H x D): 136mm x 76mm x 44mm (w/o faceplate)
Faceplate Dimensions (W x H x D): 146mm x 86mm x 6mm
Cut Out Dimensions (W x H x D): 87mm x 49mm x 39mm
Mounting Hole Spacing: UK 121mm CTC, EU 60mm CTC
Backbox Mounting Depth: 40mm (minimum), 47mm (recommended), UK or EU
double gang
Shipping Weight: 1.0Kg
Operating Temperature: 32°F to 104°F (-5°C to +55°C)
Storage Temperature: -4°F to 140°F (-25°C to +70°C)
Power Supply: 12V/1A DC
NOTE: Specifications are subject to change without notice. Weights and
dimensions are approximate.
Package Contents
HEX11WP-TX
- 1 x HEX11WP-TX
- 1 x 12V/1A DC Power Supply
- 1 x Magnetic Faceplate
- 1 x Quick Reference Guide
Certifications
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION – changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed of with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmentally safe
recycling.
Contact:
support@blustream.com.au
support@blustream-us.com
support@blustream.co.uk
www.blustream.com.au
www.blustream-us.com
www.blustream.co.uk
REVB4_HEX11WP-TX_QRG_210521
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>