DREO DR-HAF002 Smart Tower Fan User Manual

DR-HAF002 Smart Tower Fan
User Manual User Manual of Product 1:
Smart Tower Fan 

DR-HAF002 Smart Tower Fan

SereneLife 3 Person Towable Tube for Boating, Inflatable Towable Tubes for Boats 1-3 Rider, Water Sports Tube with Dual Front and Back Tow Points, Inflatable Boat
Thanks for Choosing DREOI
Your support means the world to us. We hope you enjoy our product as much as we did creating it.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL CAUTIONARY MARKINGS ON THE APPLIANCE AND SAFETY INSTRUCTIONS IN THE USER MANUAL BEFORE USE.

Do not cover the air inlet and outlet while in operation.

Do not use the fan near flammables and combustibles.
General Safety

1. Children shall not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
2. Use the appliance as described in the user manual only. Any other use not recommended in the user manual may cause fire, electrical shock, or personal injury.
3. This appliance can be used by children aged above 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this appliance in a safe way and understand the hazards involved.

Operation Safety

1. Place the appliance on a flat, dry surface before use.
2. Do not immerse in water and any other liquids.
3. Do not use the appliance until the base is installed.
4. Do not insert your fingers, pencil and any other objects into the grilles while in operation.
5. Do not dismantle, repair, or modify. All servicing should be performed by qualified personnel.

Electricity Safety

1. Make sure that the voltage of your electricity supply is the same as that indicated on the appliance.
2. Always unplug before cleaning or leaving the appliance unused for a long period of time. Keep your hands dry when plugging/unplugging.
3. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
4. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
5. WARNING: To reduce the risk of fire or electric shock, do not use this tower fan with any solid-state speed control device.
6. 24V/1.5A power adapter only. Turn off the appliance before plugging.
7. WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 30 printer).

FOR HOUSEHOLD USE ONLY READ AND SAVE THESE INSTRUCTIONS

Gentle Reminder:

Check the appliance regularly and refer to TROUBLESHOOTING or contact our customer support if it shows any of the following signs:
– Power cord or plug is damaged.
– Loud noise, unusual smell or excessive heat.
Specifications

Output: 24V 1.5A
Battery Type| CR2025 3V

ASSEMBLING YOUR TOWER FAN

Assembly Instructions
When using the appliance for the first time, remove the wraps and attach the parts by following the steps below. Keep two base halves upside down and hold them in a crossed position, then insert the pegs on one half onto the slots on the other half.
Press down on the joint areas as shown to click two base halves together.

Remove the screw nut on the bottom of the fan by rotating it counterclockwise.

Fit the base onto the fan and secure by screwing the nut back on. Put the fan upright, then plug the power adapter into the power input (located at the back of the fan), and into the power outlet.

CAUTION
Do not operate the tower fan if the base has not been installed.
Package Contents

CONNECTING TO YOUR TOWER FAN

https://bc.dreo.com/app/?model=htf004s&region=na

Before connecting the appliance to your mobile device, please scan the QR code on the left or go to the app store and search”Dreo”, then select and download the app. You can use the Oreo app to connect your smart tower fan to Amazon Alexa or Google Assistant. Please follow the in-app instructions to set up your voice assistant.
NOTE: You must create a Oreo account to access voice assistants.

1. Launch Oreo and sign in or create account by following in-a pp
   instructions.

2. Enable Bluetooth on your mobile device and plug in your tower fan.

3. Tap + Add Device and select the tower fan you want to link.

4. Hold the Oscillation button for 5 seconds to start WiFi connection settings.
   (Tip: The WiFi icon will keep flashing when pairing.)

5. Follow in-app instructions to complete WiFi connection.

6. You’re now ready to control the appliance on your app. (Tip: To restart connection settings, hold the oscillation button again for 5 seconds.)

KNOWING YOUR TOWER FAN

Control Panel

| Power Button
Turn power on/off
---|---
| Mode Button
• Switch between Normal/NaturaVSleep/Auto Mode
• Long press to mute/unmute
| Oscillation Button
• Select to start/pause oscillating
• Long press 5 seconds to start network settings and device pairing
| Decrease Button
Decrease fan speed (1-12 levels)
| Increase Button
Increase fan speed (1-12 levels)
| Timer Button
Select to set a timer (0-12h)

NOTE:
Long press and at the same time for 5s to reset to factory settings.
LED Display

NOTE:
This tower fan features auto-brightness. The display adapts automatically based on the ambient lighting conditions.
Getting the Most out of Your Tower Fan

1. It’s not an air conditioner.
2. Remove any tall obstacles that might block the airflow from the fan.
3.  Combine with your AC unit to get cooler air throughout the room.
4. Position the tower fan closer to you to get more direct airflow.
5. Place a bucket of ice in front of the fan for an extra cooling boost.

USING YOUR TOWER FAN

General Operations

Working Modes

Sleep Mode
(Mute Auto On)
Fan speed decreases every 30 minutes.
Speed decreases by three or two levels at most and will remain constant if at level 3, 2 or 1:
For level 12: 12 11 10 9
For level 11: 11 10 9 8
For level 10: 10 9 8 7
For level 9: 9 8 7 6
For level 8: 8 7 6
For level7: 7 6 5
For level 6: 6 5 4
For level 5: 5 4 3
For level 4: 4 3 3
For level 3: 3
For level 2: 2
For level 1: 1

| Auto Mode
Fan speed adapts to the ambient temperature.
---|---
| Normal Mode
Fan runs at the constant speed.
| Natural Mode
Fan runs at alternating speeds.

Additional Features

Change
Oscillation Angle| • The oscillation angle can be set to 30/60/90/120 degrees.
• To use this feature, please go to the Dreo app.
---|---
Timer| When the fan is ON/OFF, touch the timer button  repeatedly to set a timer from 1 to 12 hours. When the timer ends, the fan will stop/start running automatically. To cancel, set the time to O hour.
Note: When the auto off timer is enabled, display will return to fan speed after 3 seconds.
Mute| Method 1: Short press the mute button on the remote control to turn on/off button sounds. Long press the mode button on the
Method 2: control panel to turn on/off button sounds.
Memory| If the fan is turned OFF or disconnected from power, it will operate under the previous settings (except the
timer setting) when it is turned ON again .

Remote Control

Battery Replacement

1. Press the locking button to pop out the battery holder.
2. Replace with the same battery type with the (+) side facing up.
3. Push in the holder until securely locked into place.
   Note: If the indicator on the remote control doesn’t turn on any more, please consider replacing the battery.

WARNING
Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery  compartment does not close securely, stop using the product, remove the battery, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
The batteries must be disposed of properly, including keeping them away from children. Even used cells may cause injury.

CLEANING AND MAINTENANCE

Outer Surface
Gently wipe off the dust with a soft, dry cloth.
Base
The base can be disassembled in the reverse order of assembly.
CAUTION

1. Always unplug the fan before any cleaning or maintenance to avoid the risk of fire, electric shock, or injury to persons.
2. po not immerse in water or get water inside the motor housing.
3. Do not use any chemical agents when cleaning the fan.
4. 5tore in a cool, dry place and cover it to protect from dust.

Rear Grille
WARNING
Turn off the appliance and unplug before any cleaning and maintenance. Remove the screw on the top of the rear grille with a Phillips screwdriver.

Lift up the grille and pull it out. Dry up, then install the grille and the screw back in place, making sure the bottom pegs are fully inserted into the slots.

TROUBLESHOOTING

My fan won’t turn on!

1. Make sure that the cord is connected to a powered outlet and the mains voltage corresponds with the voltage indicated on the fan.
2. Check if the power adapter is securely inserted into the power outlet and the tower fan.
3. Protection may have been activated. Please unplug the tower fan and let it rest for 10 seconds before re-plugging in.

My fan is shaky and wobbling!

1. Place the fan on a flat, level surface.
2. Incorrect installation might also cause shakiness. Please refer to the assembly instructions in page 3-4.

My fan is making vibration and noise!

1. Place the fan on a flat, level surface.
2. Be sure not to insert anything into the air inlet and outlet.
   If your problem is not listed or still persists, please contact our Customer Support (see page 15).

DREO CUSTOMER CARE

Default 12-Month Warranty
This appliance is covered by Oreo warranty for 12 months from the date of its original purchase.
Extend Your Warranty
Extend your warranty by registering your new appliance on our website https://dreo.com/warranty.
The warranty will not apply in cases of:

1. Accident, misuse, or repairs performed by unauthorized personnel.
2.  Any unit that has been tampered with or used for commercial purposes.
3. Normal wear and tear of wearable parts.
4. Use of force, damage caused by external influences.
5. Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or noncompliance with the instructions.
6. Partially or completely dismantled appliances.
7. Defects caused by or resulting from damages from shipping or from repairs, service, or alteration to the product or any of its parts that have been perform ed by a repair person not authorized by Oreo.

We can only provide after-sales service for products that are sold by Oreo or Oreo authorized retailers and distributors. If you have purchased the appliance from a different place, please contact your seller for return and warranty issues.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a Consumer ISM equipment, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is  no guarantee that interference will not occur in a particular installation.
Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Air Circulator Fan
USER MANUAL

Thanks for Choosing DREO!
Your support means the world to us. We hope you enjoy our product as much as we did creating it.
READ ALL CAUTIONARY MARKINGS ON THE APPLIANCE AND SAFETY INSTRUCTIONS IN THE USER MANUAL BEFORE USE.

Do not cover the air inlet and outlet while in operation.  Do not use the air circulator near flammables and combustibles.
General Safety

1. Children shall not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
2. Use the appliance as described in the user manual only. Any other use not recommended in the user manual may cause fire, electrical shock, or personal injury.
3. This appliance can be used by children aged above 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this appliance in a safe way and understand the hazards involved.

Operation Safety

1. Place the appliance on a flat, dry surface before use.
2. Do not immerse in water and any other liquids.
3. Do not use the appliance until the base is installed.
4. Do not insert your fingers, pencil and any other objects into the grilles iunder any circumstances.
5. Do not dismantle, repair, or modify. All servicing should be performed by qualified personnel.
6. Do not operate the unit close to the curtain. Do not hang foreign objects on the grille to prevent damaging the balance of the fan or rotational structure.
7. Do not operate the fan under overly humid, high-temperature, dusty environment or the place where acid or alkali is stored.
8. Fans should never blow directly on infant, the elderly and patients for a long time.

Electricity Safety
WARNING:

1. Make sure that the voltage of your electricity supply is the same as that indicated on the appliance.
2. Always unplug before cleaning or leaving the appliance unused for a long period of time. Keep your hands dry when plugging/unplugging.
3. Do not operate any air circulator with a damaged cord or plug. Discard air circulator or return to an authorized service facility for examination and/or repair.
4. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
5. WARNING: To reduce the risk of fire or electric shock, do not use this air circulator with any solid-state speed control device.
6. This appliance employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions and check the appliance. If the replacement fuse blows, a short-circuit may be present and the appliance should be discarded or returned to an authorized service facility for examination and/or repair.
7. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way, If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
   WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (e.g. Parts made at home using a 3D printer).

FOR HOUSEHOLD USE ONLY READ AND SAVE THESE INSTRUCTIONS
Gentle Reminder:
Check the appliance regularly and refer to TROUBLESHOOTING or contact our customer support if it shows any of the following signs:
– Power cord or plug is damaged.
– Loud noise, unusual smell or excessive heat.
Specifications

KNOWING YOUR AIR CIRCULATOR FAN

Package Contents

USING YOUR AIR CIRCULATOR FAN

Getting the Most out of Your Air Circulator Fan

Summer:
Use with Air Conditioner
Position the air circulator in front of your AC to circulate cold air and provide better cooling.

Winter:
Use with Heater
Send the heat to corner of the room and circulate warm air faster.

Spring & Fall:
Circulation
Make the indoors as fresh and pleasant as the outdoors

Wall Mounting Your Fan (Optional)

1. Find a brick or concrete wall and mark the position where the fan will be mounted.
2.  Make sure there is a 124mm / 4.88inch distance between the two holes.
3. Screw the plastic anchors onto the wall with a drill. Leave 1/3 inch of the screws exposed.
4. Line up the holes on the base of the fan with the screws on the wall and hang the fan.

General Operations

Plug in and twist the control knob clockwise to adjust the fan speed to High, Medium, and Low.

Tilt the fan head by hand to the desired angle.
CLEANING AND MAINTENANCE

Outer Surface
Gently wipe off the dust with a soft, dry cloth.

CAUTION

1. Always unplug the air circulator before any cleaning or maintenance to avoid the risk of fire, electric shock, or injury to persons.
2. Do not immerse in water or get water inside the motor housing.
3. Do not use any chemical agents when cleaning the fan.
4. Store in a cool, dry place and cover it to protect from dust.

Front Grille and Blades
WARNING
To reduce the risk of electrical shock and injury to persons, turn off and unplug the appliance before any cleaning and maintenance.

Remove the screw on the front grille, rotate the grille counterclockwise to take it off.

Remove the blade cap by rotating it as shown and take the blade assembly out of the shaft.

Rinse cap, blades, and grille under running water or with a clean, damp cloth.

Dry up all parts, and insert the blade assembly back into the shaft by aligning the D-shaped points on the center. Align the point on the front grille with the right point on the casing , then rotate the grille clockwise and install the screw back in place.
User Servicing Instructions (Fuse)
This appliance features a fused safety plug that protects against overload or short-circuit situations. If the fuse blows, please cut off power and follow the below instructions or consult a qualified electrician .

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
3. Remove fuse carefully. Push the fuse from the other side to remove the fuse.
4. Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse .
5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

WARNING
Risk of fire. Do not replace attachment plug. Contains a safety device(fuse) that should not be removed. Discard product if the attachment plug is damaged.
My air circulator won’t turn on!
Make sure that the cord is connected to a powered outlet and the mains voltage corresponds with the voltage indicated on the air circulator.
My air circulator is shaky and wobbling!
Place the air circulator on a flat, level surface.
My air circulator is making vibration and noise!

1. Place the air circulator on a flat, level surface.
2. Be sure not to insert anything into the air inlet and outlet.
3. It is normal that the fan makes a little noise when manually adjusting the fan head.

If your problem is not listed or still persists, please contact our Customer Support (see page 12)

DREO CUSTOMER CARE

Default 12-Month Warranty
This appliance is covered by Dreo warranty for 12 months from the date of its original purchase.

Extend Your Warranty
Extend your warranty by registering your new appliance on our website https:/dreo.com/warranty.
The warranty will not apply in cases of:

1. Accident, misuse, or repairs performed by unauthorized personnel.
2. Any unit that has been tampered with or used for commercial purposes.
3. Normal wear and tear of wearable parts.
4. Use of force, damage caused by external influences.
5. Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or noncompliance with the instructions.
6. Partially or completely dismantled appliances.
7. Defects caused by or resulting from damages from shipping or from repairs, service, or alteration to the product or any of its parts that have been performed by a repair person not authorized by Dreo.

We can only provide after-sales service for products that are sold by Dreo or Dreo authorized retailers and distributors. If you have purchased the appliance from a different place, please contact your seller for return and warranty issues.

888-290-1688
support@dreo.com
www.dreo.com
Mon – Fri, 9:00 am-5:00 pm PST/PDT
www.dreo.com
Shenzhen Hesung Innovation Technology Co., LTD
26F, Bldg A7, Creative City, Shenzhen, China MADE IN CHINA www.dreo.com
DR-HTF004S
Looking for help?
Contact us to get expert support.
support@dreo.com
888-290-1688
****www.dreo.com
Mon -Fri, 9:00 am-5:00 pm PST/PDT

References

• Dreo - Elevating Smart Living | Dreo Official Brand Website
• Dreo Warranty Activation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>