BOSCH SPS2HMI54Q Dishwasher User Guide
- May 15, 2024
- Bosch
Table of Contents
**BOSCH SPS2HMI54Q Dishwasher User Guide
**
Setting up Home Connect
Tip : Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.
- Install the Home Connect app on your mobile device and follow the instructions.
- Scan the QR code with the Home Connect app
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected
here.
A table of country-specific units can be found in the instruction manual
Hardness range | mold/l | Setting value |
---|---|---|
Soft | 0 – 1.1 | H00 |
Soft | 1.2 – 1.4 | H01 |
Medium | 1.5 – 1.8 | H02 |
Medium | 1.9 – 2.1 | H03 |
Medium | 2.2 – 2.9 | H04 |
Hard | 3.0 – 3.7 | H05 |
Hard | 3.8 – 5.4 | H06 |
Hard | 5.5 – 8.9 | H07 |
Setting the water softening system
- Press .
- To open the basic settings, press Setup 3 sec. for 3 seconds.
- The display shows Hxx.
- The display shows set.
- Press Start repeatedly until the right water hardness has been set.
- To save the settings, press Setup 3 sec. for 3 seconds.
Programmed
The programme data has been meas- ured in the laboratory according to European
standard EN 60436.
The consumption figures depend on the programme and additional func- tion
selected.
The running time will change if the rinse aid system is switched off or rinse
aid needs to be added.
Programmed|
- Duration [hemin]
- Energy [kWh]
- Water [l]
---|---
Intensive 70°|
- 1:55 – 2:05
- 1.090 – 1.200
- 10.5 – 13.0
Automaton 45-65|
- 1:35 – 2:40
- 0.650 – 1.100
- 7.0 – 14.5
Eco Eco 50°|
- 3:40
- 0.831
- 9.5
Silence 50 1|
- 4:00
- 0.800
- 9.6
Express 65° – 1h|
-
1:00
-
1.050
-
10.0
-
Suitable programmer for running at night: it takes longer, but is extremely quiet.
Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programmed starts.
-
Unscrew the lid of the dispenser for special salt and remove.
-
On initial start-up: Fill the dispenser right up with water.
-
Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
-
Place the lid back on the dispenser and turn to close.
Adding rinse aid
-
Press the catch on the lid of the dispenser for rinse aid and lift .
-
Add rinse aid up to the max mar
-
Close the lid of the dispenser for rinse aid.
- The lid clicks into position.
Adding detergent
-
Add the detergent to the dry detergent dispenser.
-
Close the lid of the detergent dispenser.
- The lid clicks into position
How to use your appliance
- Load the tableware. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely
- Add detergent.
- Switch on the appliance .
- Select the programmed.
- Start the programmed Start.
- Remove the tableware at the end of the pro- grime
- To cancel the programmed, press Reset 4 sec. for approx. 4 seconds.
The programmed is cancelled and ends after ape- prox. 1 minute.
Cleaning filters
-
After each wash check the filters for residue
-
Turn the coarse filter anticlockwise and remove the filter system .
-
Pull down the micro filter to remove
-
Press the locking catches together and lift the coarse filter out .
-
Clean the filter elements under running water.
-
Re-assemble the filter system.
-
Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.
Cleaning spray arms
-
Unscrew the upper spray arms and pull down to remove
-
Pull up the lower spray arm to remove
-
Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
-
Insert the lower spray arm.
a The spray arm clicks into position. -
Insert the upper spray arms and screw firmly in place
Clean wastewater pump
-
Disconnect the appliance from the power supply.
-
Remove the filter system.
-
Scoop out any water.
-
Prize off the pump cover using a spoon and grip it by the crosspiece
-
Lift the pump cover inwards at an angle and remove.
-
Remove any remnants of food and foreign bodies in the area of the impeller.
-
Insert the pump cover and press down .
-
The pump cover clicks into position.
-
Install the filter system.
Troubleshooting
Fault | Cause and troubleshooting |
---|---|
E:61-02 will light up alternately | Supply hose is kinked. |
- Install the supply hose without kinks
Water tap is turned off.
- Turn on the water tap
Water tap is jammed or furred up.
- Turn on the water tap. The flow rate must be at least 10 l/min when the water supply is open.
The filters in the water connection of the supply or AquaStop hose are blocked.
-
Switch off the appliance.
-
Pull out the mains plug.
-
Turn off the water tap.
-
Unscrew the water connection.
-
Remove the filter from the supply hose
-
Clean the filter.
-
Re-insert the filter in the supply hose.
-
Screw the water connection back on.
-
Check the water connection for leaks.
-
Restore the power supply.
-
Switch the appliance on.
E:61-02 will light up alternately| Wastewater pump is blocked.
- Clean the wastewater pump.
Cover of the wastewater pump is loose
- Secure the cover of the Wastewater pump so it clicks into position.
E:92-40 will light up alternately| Filters are soiled or blocked.
- Clean the filt
Remnants of food on tableware| Tableware is placed too close together or basket is overfilled.
- Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware.
- Avoid points of contact.
Spray arm rotation is blocked.
- Arrange tableware so that it does not obstruct spray arm rotation.
Spray arm nozzles are blocked.
- Clean the Spray arms.
Filters are soiled.
- Clean the filters.
Filters are inserted incorrectly and/or not engaged.
- Insert the filters properly.
- Engage the filters.
Washing programmed selected too weak.
- Select a more intensive washing programmed.
Removable streaks are present on glasses, glassware with a metallic appearance and cutlery| Amount of rinse aid to be dispensed is set too high.
- Set the rinse aid system to a lower setting
No rinse aid has been added.
- Add rinse aid.
Rust spots on cutlery.| Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected.
- Use rust-resistant tableware
Cutlery may also rust if washed together with rusting items.
- Do not wash rusting items
Detergent residue is present in the detergent dispenser or the tablet collecting tray.| Spray arms were blocked by tableware so detergent was not rinsed out.
- Check that the spray arms are not blocked and can rotate freely.
All LEDs light up or flash or the rinse programmed does not continue running.| Electronics have detected a fault.
- Press the main switch button for approx. 4 seconds. The appliance is reset and restarted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>