RYOBI RPD18X Cordless Combi Drill Instruction Manual

RPD18X Cordless Combi Drill
Instruction Manual

RPD18X Cordless Combi Drill

Important!
It is essential that you read the instructions in this manual before assembling, maintaining, and operating the product.
Subject to technical modificatio
Safety, performance, and dependability have been given top priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults who have read and understood the instructions and warnings in this manual and can be considered responsible for their actions.
The product is intended for drilling into various materials, including wood, metal, and plastics using a drill bit having a shank diameter of less than 13 mm. The product can be used to drive and remove screws and bolts using an appropriate bit.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the in a hazardous situation.
WARNING! Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below Save all warnings and instructions for future reference.

PERCUSSION DRILL SAFETY WARNINGS

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
• Use the auxiliary handle(s). Loss of control can cause
• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring.
  Cutting accessories or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS

• Never operate at a higher speed than the maximum
  speed rating of the drill bit. At higher speeds, the
  bit is likely to bend if allowed to rotate freely without

• Always start drilling at low speed and with the bit
  tip in contact with the workpiece. At higher speeds,
  the bit is likely to bend if allowed to rotate freely without

• Apply pressure only in direct line with the bit and do
  not apply excessive pressure. Bits can bend causing

ADDITIONAL SAFETY WARNINGS

• Clamp the workpiece with a clamping device. Unclaimed workpieces can cause severe injury and damage.

• Dust created by operating the product can cause filters suitable for protecting against particles from the material being worked on.

• Injuries may be caused or aggravated by prolonged use of a tool for prolonged periods, ensure you take regular breaks.

• Switch off the product immediately if the bit stalls. Do not switch on the product again while the bit is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the bit stalled and rectify this, paying heed to the safety instructions.
  The possible causes may be:
  – it is tilted in the workpiece
  – it has pierced the workpiece
  – the product is overloaded

• The ambient temperature range for the tool during operation is between 0°C and 40°C.

• The ambient temperature range for tool storage is between 0°C and 40°C.

• The recommended ambient temperature range for the charging system during charging is between 10°C and 38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

• To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
• The ambient temperature range for batteries during use is between 0°C and 40°C.
• The ambient temperature range for battery storage is between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labeling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 56.

1. Gear selector
2. Torque adjustment ring
3. Keyless chuck
4. The direction of the rotation selector
5. Variable speed switch trigger
6. Handle, insulated gripping surface
7. LED light
8. Battery port
9. Auxiliary handle, insulated gripping surface
10. Screwdriver bit
11. Operator’s manual
12. Battery pack
13. Charger

MAINTENANCE

The product should never be connected to a power supply when assembling parts making adjustments cleaning, performing maintenance, or when the product is not in use. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.

• When servicing, use only the original manufacturer’s replacement parts, accessories, and attachments. Use of any other parts may create a hazard or cause product damage.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
• Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
• For greater safety and reliability, all repairs should be performed by an authorized service center.

SYMBOLS ON THE PRODUCT

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
SYMBOLS IN THIS MANUAL

| Note
---|---
| Parts or accessories are sold separately
| Torque, maximum
| Torque, minimum
| Speed, minimum
| Speed, maximum

|
---|---
|

Battery and charger
Compatible battery pack (not included)
Lithium-Ion
The compatible charger (not included)

Product specifications

Percussion drill
Model
Voltage
Chuck
Switch – Variable speed
No-load speed (Drill mode)
LO Speed
HI Speed
Impact rate (Percussion drill mode)
LO Speed
HI Speed
Clutch (positions)
Maximum torque
Maximum drilling capacity, in wood
Maximum drilling capacity, in metal
Maximum drilling capacity, in masonry
Weight – excluding battery pack
Weight – according to EPTA Procedure 01/2014
Measured sound values determined according to EN 62841:
A-weighted sound pressure level
Uncertainty K
A-weighted sound power level
Uncertainty K
Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN 62841:
Impact drilling into concrete
Uncertainty K
Drilling into metal
Uncertainty K

WARNING
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in accordance with a standardized test and may be used to compare one tool with another. They may be used for a preliminary assessment of exposure.
The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ.
These conditions may significantly increase the exposure levels over the total working period. An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is running idle. These conditions may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the accessories, keeping the hands warm (in case of vibration), and organizing work patterns.

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

1. The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only to new products.

2. There is a possibility to extend a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for the extended warranty is clearly displayed in stores and/or on the packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.

3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
   – any damage to the product that is the result of improper or lack of maintenance
   – any product that has been altered or modified
   – any product where original identification (trademark, serial number) markings have been defaced, altered, or removed
   – any damage caused by non-observance of the instruction manual
   – any product not displaying the CE approval mark on the rating plate
   – any product that has been attempted to be repaired by a non-authorized warranty service center or without prior authorization by Techtronic Industries
   – any product connected to the improper power supply (amps, voltage, frequency)
   – any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
   – normal wear and tear spare parts
   – inappropriate use, overloading of the tool
   – use of non-approved accessories or parts
   – Power tool accessories provided with the tool or purchased separately, including but not limited to screwdriver bits, drill bits, abrasive discs, sandpaper and blades, lateral guide, etc.
   – Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc.

4. For servicing, the product must be sent or presented to an RYOBI-authorised service station listed for each country in the following list of service station addresses. In some countries, your local RYOBI dealer undertakes to send the product to the RYOBI service organization. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with the sender’s address, and accompanied by a short description of the fault.

5. A repair/replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries, delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected

6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE
Any request or issue with the product can be addressed to your local authorized service centers (visit www.ryobitools.eu) or directly to Techtronic Industries GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number and product type printed on the label.

EC DECLARATION OF CONFORMITY
Percussion drill
Brand: RYOBI | Model number¹
Serial number range²
We declare as the manufacturer under our sole responsibility that the product mentioned below fulfills all the relevant provisions of the following European Directives, European Regulations, and harmonized standards³
Authorized to compile the technical file:4

1. RPD18X
2. 47551001000001 – 47551001999999
3. 2006/42/EC, 2014/30/EU, 2011/65/EU, EN 55014-1:2017+A11:2020,
   EN 55014-2:2015, EN 62841-1:2015, EN 62841-2-1:2018+A11:2019,
   EN IEC 63000:2018

Todd Chipper
Vice President, Quality – Ryobi Asia
Winnenden, Feb. 26, 2021

4. Alexander Krug, Managing Director
   Techtronic Industries GmbH
   Max-Eyth-Straße 10, 71364 Winnenden, Germany

DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product mentioned below
Percussion drill
Brand: RYOBI
Model number: RPD18X
Serial number range: 47551001000001 – 47551001999999 fulfills all the relevant provisions of the following Regulations: S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used:
BS EN 55014-1:2017+A11:2020, BS EN 55014-2:2015, BS EN 62841-1:2015,
BS EN 62841-2-1:2018+A11:2019, BS EN IEC 63000:2018

Todd Chipper
Vice President, Quality – Ryobi Asia
Winnenden, Feb. 26, 2021
Authorized to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
RYOBI is a trademark of Ryobi Limited and is used under license.

Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK
961075662-01B

References

• Ryobi Tools
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>