eSUN Pro 3 Vacuum Storage Bag for 3D Printer Filament User Manual

eSUN Pro 3 Vacuum Storage Bag for 3D Printer Filament

Product Information

Specifications

• Electric Pump
  • Size: 10.4 x 4 x 4 cm
  • Weight: 113 g
  • Material of pump: ABS
  • Suction power: 4 L/minute

Product Information:

The eVacuum Kit Pro 3 is a kit of vacuum storage bags designed for 3D printer filament. It helps preserve opened 3D printing materials that easily absorb moisture, such as PVA, ePA, ePA-CF, ePA-GF, ABSMAX, and TPU-95A. The kit creates an airtight seal to prevent material degradation and is portable for home use. It is recommended to pair this kit with the eBOX for optimal results. The  materials used are BPA-free, FDA-approved food-grade plastics,ensuring safety and eco-friendliness.

Product Usage Instructions

1. Place the 3D filament and desiccant in the vacuum bag.
2. Remove some air and seal the vacuum bag using a sealing clip.
3. Aim the electric pump at the air outlet, vacuum the air out of the bag, and press the air outlet to form a seal.
4. The contents are now vacuum-packed.

Troubleshooting:

Open the zipper of the bag and reseal the zipper with the
sealing clip to ensure it is completely closed.| Bag is not completely closed.|
Re-position Bag so the Air Valve lies flat.| The air valve is not placed on a flat surface when pumping
air.|
Ensure the air suction tip is centered and placed flat on air
valve. Apply moderate pressure.| The inlet of the electric pump is not in full contact with the
air valve.|
Remove air from the bag again. Immediately press center of air
valve with finger to ensure seal.| The air leaks or the bag is broken.| Change to a new bag if needed.

Introduction

The 3D Printing Consumables Vacuum Kit preserves opened 3D printing materials that absorb moisture easily. It creates an airtight seal to prevent degradation of materials like PVA, ePA, ePA-CF, ePA-GF, ABSMAX and TPU-95A. This portable kit is for home use, pairs with the eBOX for optimal results, and is made of BPA-free, FDA-approved food-grade plastics, ensuring safety and eco-friendliness.）

Accessories

1. 10x Vacuum bags
2. 2x Sealing clips
3. 15x *Desiccant bags
4. 1x Electric pump ( *allochroic silica gel )

Method of Use

1. Place 3D filament and desiccant in the bag.
2. Try to remove some air and then seal the vacuum bag using a sealing clip.
3. Aim the electric pump at the air outlet, vacuum the air out of the bag, and finally press the air outlet to form a seal.
4. The contents are now vacuum packed.

SPECIFICATIONS

• Electric Pump
  • Size: 10.4 x 4 x 4 cm
  • Weight: 113 g
  • Material of pump: ABS
  • Suction power: ≥ 4 L / minute
• Vacuum Bags
  • Size: 33 x 38 cm
  • Thickness: 0.090 mm
  • Material: PA+PE，BPA free & FDA approved
  • Storage temperature: -20 to +85°C

Desiccant

• Size: 45 x 45 mm
• Weight: 3 g / bag
• Material: Blue silica gel
• Water absorption rate: 30 %+

Attention:

1. Keep out of reach of the children.
2. The desiccant must not be ingested.
3. Avoid direct sunlight and moisture.
4. Keep in a dry and cool environment.
5. Please keep it sealed when not use.
6. Please replace with a new one when desiccant changes from blue to pink.

TROUBLESHOOTING

to ensure that the zipper is completely closed
The air valve is not placed on a flat surface when pumping air| Re-position Bag so the Air Valve lies flat.
The inlet of the electric pump is not in full contact with the air valve| Ensure the air suction tip is centered and placed flat on air valve. Apply moderate pressure.
The electric pump is not working properly| Check if the wire is damaged and the connector is connected properly
Air Valve is not closed| Remove air from bag again. Immediately press center of air valve with finger to ensure seal.
The bag is broken| Change a new one.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>