eSUN 2799087 eVacuum Kit Pro 2 User Manual
- June 12, 2024
- eSUN
Table of Contents
eSUN 2799087 eVacuum Kit Pro 2
Product Information
| Product Name | eVacuum Kit Pro 2 |
|---|---|
| Product Type | Kit of Vacuum Storage Bag for 3D Printer Filament |
| Features | – Creates an airtight seal to prevent degradation of materials |
like PVA, ePA, ePA-CF, ePA-GF, ABSMAX and TPU-95A
– Made of BPA-free, FDA-approved food-grade plastics
– Portable and suitable for home use
– Pairs with the eBOX for optimal results
Product Usage Instructions
- Place the 3D filament and desiccant in the vacuum bag.
- Try to remove some air from the bag and then seal it using asealing clip.
- Aim the electric pump at the air outlet of the bag.
- Vacuum the air out of the bag using the electric pump.
- Finally, press the air outlet to form a seal.
Specifications
Electric Pump| Size: 10.3 x 3.4 x 3.4 cm
Weight: 110 g
Material: ABS
Suction Power: 4 L/minute
---|---
Vacuum Bags| Size: 45 x 45 mm
Weight: 3 g/bag
Desiccant| Material: Blue silica gel
Water absorption rate: 30%+
Attention:
– Keep out of reach of children
– Do not ingest the desiccant
– Avoid direct sunlight and moisture
– Store in a dry and cool environment
– Keep sealed when not in use
– Replace with a new one when desiccant changes from blue to
pink
Troubleshooting
| Problem | Possible Cause | Solution |
|---|
Open the zipper of the bag and reseal the zipper with the
sealing clip to ensure that the zipper is completely closed| Bag is not
completely closed| Reseal the zipper with the sealing clip to ensure complete
closure
The air valve is not placed on a flat surface when pumping
air| The inlet of the electric pump is not in full contact with the
air valve| Re-position the bag so that the air valve lies flat on a flat
surface
The vacuum bag cannot be vacuumed or the air leaks| The inlet of the electric
pump is not in full contact with the
air valve| Ensure the air suction tip is centered and placed flat on the
air valve. Apply moderate pressure.
The electric pump is not working properly| Check if the wire is damaged and
the connector is connected
properly| Inspect the wire for damage and ensure proper connection of the
connector
Air valve is not closed| The bag is broken| Remove air from the bag again.
Immediately press the center of
the air valve with a finger to ensure a seal. If the bag is broken,
replace it with a new one.
Please read the user manual before using the eVacuum Kit.
Introduction
The 3D Printing Consumables Vacuum Kit preserves opened 3D printing materials that absorb moisture easily. It creates an airtight seal to prevent degradation of materials like PVA, ePA, ePA-CF, ePA-GF, ABSMAX and TPU-95A. This portable kit is for home use, pairs with the eBOX for optimal results, and is made of BPA-free, FDA-approved food-grade plastics, ensuring safety and eco-friendliness.）
Accessories
- 10x Vacuum bags
- 2x Sealing clips
- 15x *Desiccant bags
- 1x Electric pump
( *allochroic silica gel )
Method of Use
- Place 3D filament and desiccant in the bag.
- Try to remove some air and then seal the vacuum bag using a sealing clip.
- Aim the electric pump at the air outlet, vacuum the air out of the bag, and finally press the air outlet to form a seal.
- The contents are now vacuum packed
SPECIFICATIONS
Electric Pump
- Size：10.3 x 3.4 x 3.4 cm
- Weight：110 g
- Material of pump: ABS
- Suction power: ≥ 4 L / minute
Vacuum Bags
- Size：33 x 38 cm
- Thickness: 0.090 mm
- Material: PA+PE，BPA free & FDA approved
- Storage temperature: -20 to +85°C
Desiccant
- Size：45 x 45 mm
- Weight：3 g / bag
- Material: Blue silica gel
- Water absorption rate：30 %+
Attention：
- Keep out of reach of the children.
- The desiccant must not be ingested.
- Avoid direct sunlight and moisture.
- Keep in a dry and cool environment.
- Please keep it sealed when not use.
- Please replace with a new one when desiccant changes from blue to pink
TROUBLESHOOTING
| Problem | Possible Cause | Solution |
|---|
The vacuum bag cannot be vacuumed or the air leaks
| ****
Bag is not completely closed
| Open the zipper of the bag and reseal the zipper with the sealing clip to ensure that the zipper is
completely closed
The air valve is not placed on a flat surface when
pumping air
| ****
Re-position Bag so the Air Valve lies flat.
The inlet of the electric pump is not in full contact
with the air valve
| Ensure the air suction tip is centered and placed flat on air
valve. Apply moderate pressure.
The electric pump is not working properly
| ****
Check if the wire is damaged and the connector is connected properly
Air Valve is not closed
| Remove air from bag again. Immediately press center of air
valve with finger to ensure seal.
The bag is broken| Change a new one.
Better nature , better life
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>