Wooken B0BRKLP1C8 Electric Bike 20 Inch X4.0 Fat Tire Electric Bike User Manual

Wooken B0BRKLP1C8 Electric Bike 20 Inch X4.0 Fat Tire Electric Bike

Part 1 PRODUCT SAFETY NOTICE

Before your riding, please read this manual carefully and observe the following precautions:

1. Please remember to wear a helmet or other protectors to avoid injury when riding your electric bike.
2. Please make sure that all parts of the electric bike are properly installed and not damaged.
3. Please check whether the folded part is locked and the brake system is well.
4. Before use, please confirm whether the power is sufficient.
5. Before your riding, be sure to check that the tyres are in good condition, inflated properly, and have sufficient tread remaining.
6. When feeling unwell physically or mentally due to illness or under the influence of medicine or alcohol, please do not ride an ebike.
7. The E-bike is designed for only one rider, and never try to ride double or more or ride the e-bike holding a child or load.
8. Please do not climb the slope over 15°, and do not sharply speed up or slow down on the slope.
9. Never exceed the 330 lbs (150kg) maximum load.
10. Do not ride under wet conditions. The ebike may slide from under your feet causing injury. Wet conditions may damage the electronics and void the warranty.
11. Do not modify the product from the manufacturer’s original design.
12. Electric bicycle is only used as a daily means of transportation, and should not be used in extreme sports or other dangerous riding methods.
13. Don’t go up and down steps. Don’t ride on the highway and in heavy rain.

Part 2 PACKAGE CONTENTS
Please carefully check the package contents, any missing or damaged, please feel free to contact our customer service for support.

Part 3 PRODUCT OVERVIEW

1. Reflector

2. Front Suspension

3. Built-in Battery

4. Seat Clamp

5. Pedal

6. Brake

7.  Disc Brake

8. Charging Port

9. Rear Suspension

10. Throttle

11. Horn/light Button

12. Saddle

13. Motor

14. Headlight

15. LCD Display

16. Reflector

17. Kickstand

18. Brake

19. Front Reflector

20. Horn Swich

21. Shift Button

22. Electric Drive Upshift Button

23. Brake

24. Electric Drive Downshift Button

25. Throttle

26. Power Switch

27. Headlight Switch

28. LCD Display

Part 4 INSTALLATION GUIDE

ASSEMBLE HANDLEBAR

1. Lift the handlebar stem.

2. Press the stem quick release to lock.

3. Lock the clamp.

4. Loose the screws.

5. Put the handlebar on the groove of the tube.

6. Close the clamp.

7. Tighten the screws and close the clamp.
   Notes:

8. Please make sure the front wheel is fixed in the right position to avoid serious injury caused by a loose wheel.

9. Battery keys are included. Please keep them safe.

BASSEMBIE EDONT WHEEL

1. Loose the screws.
2. Tighten the screws.
3. Align the grooves.
   Notes: Please make sure the front wheel is fixed in the right position to avoid serious injury caused by a loose wheel.

ASSEMBLE SADDLE

1. Open the stem clamp of the seat post
2. Slide the seat into the stem tube adjust the seat height and make sure the head of the seat is parallel with the top tube.
3. Close the stem clamp of the seat post and make sure the seat is secured.

Notes
Please don’t raise the seat post above the “Minimum Insertion” line printed on the back of the seat post. Raising the seat post above the minimum insertion line may cause you to be injured while riding.

ASSEMBLE PEDALS

1. The pedals in the package have an “L” or “R” label to indicate whether it should be installed on the left or right side.
2. To Install the left “L” pedal, screw it counter-clockwise by hand, and turn it clockwise to install the right pedal.

ASSEMBLE HEADLIGHT

1. Use the included tools to lose the screw.
2. Attach the headlight in place and tighten thescrew.
3. Adjust the headlight position and press the switch button to check whether it works.

Part 5 BATTERY CHARGING GUIDE
This fat tyre electric bike adopts a built-in removable battery, with 2 charging methods: directly charging the ebike and removing the battery to charge. When charging, the charger indicator turns red; when the charger turns green, the battery is fully charged.

CHARGING ON THE EBIKE – charging port

1. Remove the rubber cover from the charging port on the ebike frame. charging
2. Fully Charged Connect the ebike with the charger and then plug the charger into a power outlet. When the charger turns red to green, the battery is fully charged.
3. Unplug the charger first, twist the key clockwise to turn on the battery and then press the middle button for 3 seconds to turn on the display. After that, you can check the battery levels.

CHARGE OFF THE EBIKE
Remove the battery from the bike, connect the battery to the charger and then plug the charger into a power outlet.

How to remove the battery?

Step 1
Push the key in the deep and then turn the key counterclockwise to unlock the battery.

Step 2
Press the button to open the clamp. charging port

Step 3
The battery can be removed by unfolding the frame slightly.

Fully Charged
When the charger turns red to green, then the battery is fully charged.

Warm Tips

• When the battery is charging, the LCD automatically turns off.
• The key is always on the ebike when you use pure ebike mode and padel-assisted mode. Please don’t remove the key during your ride. Please keep your keys carefully.

How to twist the key?

Part 6 RIDING MODES
Notes: Press down on the middle button for at least 3s to turn on the LCD. The speed and riding range is also influenced by riding style, weight, road conditions, etc.

Part 7 LCD DISPLAY AND BUTTON

Part 8 SPECIFICATIONS

Part 9 DAILY CARE AND MAINTENANCE – CLEANING AND STORAGE

1. If you see stains on the bike body, wipe them off with a damp cloth. If the stains won’t scrub off, put on some toothpaste, and brush them with a toothbrush, then wipe them off with a damp cloth.
   Notes: Do not clean the bike with alcohol, gasoline, kerosene, or other corrosive and volatile chemical solvents to prevent dire damage. Do not wash the bike with a high-pressure water spray.

2. During cleaning, make sure that the bike is turned off, the charging cable is unplugged, and the rubber flap is closed as water leakage may result in electric shock or other major problems.

3. Please try to store the bike in a cool and dry place between 50°F -77″ F (10″C -25). In extremely humid environments the interior of the bike may suffer condensation or even water accumulation, which may damage the battery rapidly.

4. Devices are not intended for use at elevations greater than 2000m above sea level of prolonged exposure to UV rays, rain, and the elements that may damage the enclosure materials, and store them indoors when not in use.

5. Do not put it outdoors for a long time. Excessive sunlight, overheating and overcooling accelerate the battery life span

6. In daily use, try to avoid recharging the bike after completely exhausting the battery. If the battery is low, charge it as soon as possible.

7. Please charge the bike every other month to preserve the battery

BATTERY MAINTENANCE AND DISPOSAL

1. Using the original battery, using other models or brands may bring about safety issues;
2. Do not dismantle or puncture the casing. Keep the ports away from metal objects to prevent short circuits which may result in battery damage or even injuries and deaths;
3. Use the original power adapter to avoid potential damage or fire;
4. Mishandling of used batteries may do tremendous harm to the environment.
5. To protect the natural environment, please follow local regulations to properly dispose of used batteries.

BEFORE RIDE SAFETY CHECKLIST
Before every ride, we advise you to follow the pre-ride safety checklist. Also, wear a qualified helmet to avoid any possible injuries during the ride.

Part 10 WARRANTY AND CUSTOMER SERVICES

WARRANTY
We provide a one-year warranty for the ebike components and tech support. If there is a defect when you receive the package and damage under normal use during the warranty period, we will resend you a new part and help you solve the problem.
Note: The Warranty does not apply to any damage due to improper use, failure to follow the lincrusta- tions, unauthorized maintenance and repair, or external causes such as accidents, abuse other force majeure.

CUSTOMER SERVICES
Your satisfaction is our top priority. We provide lifelong technical support. If there is any issue with the ebike, don’t hesitate to contact our customer services. Find your order, then send us the relevant photos and videos. We will respond soon on Business day.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including inter- reference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: from that to which the receiver is connected.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FOR YOUR SAFETY, PLEASE WEAR A HELMET DURING YOUR RIDE
Stand over the bicycle and straddle tne top tube proper clearance is a minimum of 1″(25mm) between the highest part of the top tube inseam of the rider.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>