BOSCH Professional GCT 30-42 System Accessories User Manual

: May 15, 2024
: Bosch

BOSCH Professional GCT 30-42 System Accessories

BOSCH-Professional-GCT-30-42-System-Accessories-fig-1

Product Information

Specifications

Brand: Bosch Power Tools GmbH
Model: GCT 30-42 Professional
Country of Origin: Germany
Frequency Range: Utilized frequency range
Output Power: Less than 10 mW
Battery Type : 3-V Lithium CR 2032
Dimensions: 240 mm
IP Rating: IP54

Product Usage Instructions

Components Overview

Transmitter Module
LED Status Indicator (User Interface)
Start/Stop Button (User Interface)
Mounting Hook Rubber Band
Rubber Band

Mounting and Operation of Transmitter Module
To mount the transmitter module:

Insert the battery into the module.
Attach the transmitter module securely to the desired location.

Startup Process
To start the operation of the device:

Press the Start/Stop button on the transmitter module.
The device will automatically start when vibrations from the power tool are detected by the transmitter module.

Status Indicators
The LED indicator on the User Interface provides the following information:

Blue: Indicates a certain status or event.
Yellow: Represents a different state or event.
Red: Indicates a specific condition or event.

Maintenance and Service
To replace the button cell:
Always replace the button cell with a suitable replacement.

Frequently Asked Questions (FAQ)

What should I do if the device is not starting automatically?
Check the battery level in the transmitter module and ensure it is properly mounted for vibration detection.
How often should I replace the button cell?
It is recommended to replace the button cell as per the instructions provided in the manual or when the device shows signs of low battery.

Safety instructions

All instructions must be read and observed in order to enable work with the GCT 30-42 to be carried out safely. Store these instructions in a safe place and include them with the GCT 30-42 when giving it to a third party.
Ensure that the coin cell is kept out of the reach of children. Coin cells are dangerous.

Coin cells must never be swallowed or inserted into any other part of the body. If you suspect that someone has swallowed a coin cell or that a coin cell has entered the body in another way, seek medical attention immediately. Swallowing coin cells can result in severe internal burns and death within 2 hours.
Ensure that coin cell replacement is carried out properly. There is a risk of explosion.
Only use the coin cells listed in this operating manual. Do not use any other coin cells or other forms of electrical power supply.
Do not attempt to recharge the coin cell and do not short circuit the coin cell. The coin cell may leak, explode, catch fire and cause personal injury.
Remove and dispose of drained coin cell correctly. Drained coin cell may leak and damage the product or cause personal injury.
Do not overheat the coin cell or throw it into fire. The coin cell may leak, explode, catch fire and cause personal injury.
Do not damage the coin cell and take the coin cell apart. The coin cell may leak, explode, catch fire and cause personal injury.
Do not allow damaged coin cells to come into contact with water.
Leaking lithium may mix with water to create hydrogen, which could cause a fire, an explosion, or personal injury.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Robert Bosch Power

Tools GmbH is under license.
Never fasten the Auto-Start remote to places which are required to operate the cordless tool (such as gripping surfaces, switches, displays).

Product description and specifications

Intended Use

The Auto-Start remote GCT 30-42 generates a start-stop signal for a dust extractor.
This signal can be transmitted to either a Bosch Professional dust extractor with Auto-Start function or a GCA 30-42 receiver.
Refer to the operating instructions for the GCA 30-42 + GCT 30-42 Auto-Start system or the dust extractor that is being used for more information.

Product Features

The numbering of the product features shown refers to the illustrations on the graphic pages.

BOSCH-Professional-GCT-30-42-System-Accessories-fig-2

Auto-Start remote
LED status indicator (user interface)
Start/stop button (user interface)
Fastening hook for rubber band
Rubber band

Technical Data

Article number 1 600 A02 GH.
Operating temperature –20 to +50 °C
Storage temperature –20 to +65 °C
Dimensions A) 43 x 18 x 42 mm
Rubber band length 240 mm
Protection class IP54
Data transfer
- Bluetooth® Bluetooth® 4.2 (Low Energy)
- Frequency range used 2402–2480 MHz
- Output power < 10 mW
Energy supply Bluetooth® Low Energy module
Coin cell 3 V lithium battery, CR 2032
Without rubber band
Values can vary depending upon the product and are subject to application and environmental conditions. For further information www.bosch- professional.com/wac.

Assembly and Operation

Mounting the Auto-Start Remote

Attach one end of the rubber band (5) to one of the two fastening hooks (4).
Secure the Auto-Start remote (1) to the cordless tool. To do so, tighten the rubber band (5) and attach the free end to the second fastening hook (4).
Cut the rubber band to the correct length, as necessary. Appropriate places are those at which the cordless tool generates sufficient vibration during operation. Never fasten the Auto-Start remote to places which are required to operate the cordless tool (such as gripping surfaces, switches, displays).

Starting operation

Connect the GCT 30-42 Auto-Start remote to the GCA 30-42 receiver or to the appropriate Bosch Professional dust extractor.
Read the Starting Operation and Establishing a Connection sections in the operating instructions for the GCA 30-42 + GCT 30-42 Auto-Start system or the dust extractor that is being used.

When changing a coin cell, the following shall apply:

If the GCT 30-42 transmitter module was connected to the GCA 30-42 receiver module before changing the coin cell, the connection is automatically re-established after changing the coin cell.
If the modules were not connected before replacing the coin cell, the connection needs to be established. After a reset, the Auto-Start remote and the receiver must be reconnected.

Auto Starting the Dust Extractor

Insert the extraction hose into the dust extraction attachment of the cordless tool.

Vibration Detection

The GCT 30-42 transmitter module is equipped with vibration detection. If it detects the vibrations of the activated cordless tool, the dust extractor will switch on automatically.
If you switch off the cordless tool, the dust extractor switches off automatically after a certain run-on time.
Switching On and Off Manually
Briefly press the start/stop button (3) on the Auto-Start remote (1).
The dust extractor switches on.
To switch off the dust extractor, press the start/stop button (3) on the

Auto-Start remote again.
Note: If you switch off the dust extractor with the start/stop button (3) on the Auto-Start remote, the dust extractor will automatically switch on again once the Auto-Start remote (1) detects the vibrations of the cordless tool.

Resetting to Factory Settings
Press and hold the start/stop button (3) until the LED status indicator (2) flashes blue four times in quick succession.

Status indications

BOSCH-Professional-GCT-30-42-System-Accessories-fig-3

Maintenance and Service

Maintenance and Cleaning
Remove any dirt using a brush or a damp cloth. Do not use any detergents or solvents.

Changing the Coin Cell

Caution: The coin cell must always be replaced with a coin cell of the same type. There is a risk of explosion.
Remove and dispose of drained coin cell correctly. Drained coin cell may leak and damage the product or cause personal injury. Open the battery compartment cover on the rear of the Auto-Start remote with a coin.
Carefully remove the coin cell and insert a new coin cell. Pay attention to the markings for correctly inserting the coin cell.
Close the battery compartment cover with a coin. Turn the cover as far as it will go to ensure that it is closed properly.

After-Sales Service and Application Service

Der Kundendienst beantwortet Ihre Fragen zu Reparatur und Wartung Ihres
Produkts sowie zu Ersatzteilen. Explosionszeichnungen und Informationen zu
Ersatzteilen finden Sie auch unter: www.bosch-pt.com
Das Bosch-Anwendungsberatungs-Team hilft Ihnen gerne bei Fragen zu unseren Produkten und deren Zubehör.
Geben Sie bei allen Rückfragen und Ersatzteilbestellungen bitte unbedingt die 10-stellige Sachnummer laut Typenschild des Produkts an.

ABOUT COMPANY

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Further service addresses can be found at:www.bosch-pt.com/serviceaddresses

Disposal

The Auto-Start remote, accessories and packaging should be sorted for environmental- friendly recycling.
Do not dispose of electronic components and batteries into household waste!

Licenses

Copyright © 2012–2020 STMicroelectronics
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright © 2011 Petteri Aimonen
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
This notice may not be removed or altered from any source distribution.

Declaration of Conformity

Hereby, Robert Bosch Limited as authorised representative acting on behalf of Robert Bosch Power Tools GmbH declares that the radio equipment type GCT 30-42 is in compliance with the Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: https://gb-doc.bosch.com