PRO USER ELECTRONICS SCP10 Solar Panel Battery Controller Instruction Manual
- May 15, 2024
- PRO USER ELECTRONICS
Table of Contents
Pro-User Electronics SCP10 Solar Panel Battery Controller Instruction
Manual
SCP10
Solar Panel Battery Controller
12V/24V
OPERATING MANUAL
PWM SOLAR BATTERY CONTROLLER 10A
SUITABLE FOR STANDARD LEAD-ACID, AGM & LiFePO4 (12V) BATTERIES
Read this manual before using this product.
Failure to do so can result in serious injury.
Important Safety Instructions & Warnings
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for the Pro-User Electronics solar panel battery controller.
Pro-User Electronics accepts no liability for direct or indirect damage caused by faulty assembly or connection, a usage of damaged or altered products, a usage for purposes other than described and especially caused by failure to follow these instructions.
- Battery posts, terminals and related accessories contain lead and lead components, and other chemicals known to the State of European to cause cancer and birth defects or other reproductive harm. Always wash your hands after handling these devices.
- Do not operate the solar panel battery controller with damaged wiring. Replace wires immediately if damaged.
- All lead acid batteries have the potential to emit gasses that may combine into a combustible or explosive mixture. In many cases, it is possible that lead acid batteries will emit these gasses during normal discharge and charging operations. Because of this potential danger, it is important that you follow the precautions recommended by both the battery and battery charger manufacturers before using either one. For example, do not exceed the recommended maximum recharge rate (charger output current limit), or remove cell caps while charging flooded batteries.
- Install the solar panel battery controller as far away from the battery as possible and in a well ventilated area.
- Do not expose the Solar Charger Controller to any rain, snow, spray, or moisture of any kind. This device is not designed for outdoor use.
- Do not use attachments that are not recommended or sold by the charger manufacturer. To do otherwise may result in the risk of electric shock, fire, or possibly some other unforeseen potential personal injury situations.
- When leaving a battery charger connected to either a sealed (AGM or GEL) or non-sealed (flooded battery) for extended periods of time (weeks, months, etc.), periodically check the battery to see if it is unusually warm. This is an indication that the battery may have a weak cell and that it could go into a thermal runaway condition. If the battery releases an excessive amount of gas or if the battery gets hotter than 55 degrees during charging, Disconnect the charger and allow the battery to cool. Overheating may result in plate distortion, internal shorting, drying out or other damage. For flooded batteries, also check individual cell fluid levels against manufacturer’s recommendations for safe operation.
- Never smoke or allow a source of electric spark or open flame in the vicinity of the battery or engine. (For example: don’t charge the battery next to a gas water heater.)
- Do not operate the solar panel battery controller where ventilation is restricted. The intent here is to allow sufficient airflow to minimize and dissipate the heat generated by the Solar Charger Controller and to diffuse the gasses that may be emitted by the battery.
- Never disassemble or attempt to do internal repairs. This voids the warranty. Disassembling the Solar Charger Controller incorrectly may result in the risk of electric shock or create a fire hazard.
- Never charge a visibly damaged or frozen battery.
- After opening the package, examine all parts for visible damage. If you have found any damage, please contact the company you purchased this unit from.
- Electrical devices are not toys. Keep the product away from children.
Personal precautions when you work near lead-acid batteries:
- Someone should be within range of your voice or close enough to come to your aid if you have an accident.
- Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
- Wear complete eye protection and protective clothing. Avoid touching your eyes while working near a battery. If battery acid contacts your skin or clothing, wash immediately with soap and water. If acid enters an eye, immediately flood the eye with running cold water for at least 10 minutes and get medical attention as soon as possible.
- Be extra cautious when handling metal tools around a battery. If you drop a metal tool near a battery it might spark or create a short circuit between the battery terminals and some other metal part. Either event may cause a dangerous electrical shock hazard, a fire, or even an explosion.
- Remove all personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short-circuited current high enough to weld a metal ring or other piece of jewelry, causing a severe burn.
Product Specifications
Package contents:
- Solar panel battery controller SCP10 (PWM)
- Instruction manual
Wiring Scheme
Explanations
- Solar panel + positive input
- Solar panel – negative input
- Battery + positive output
- Battery – negative output
- Load + positive output
- Load – negative output
- Solar panel Charging LED – Flashes during charging, turns solid when fully charged. If insufficent sun light the LED will not illiminate.
- Battery voltage indicator.
- Error warning LED – Green no issues, Red indicates a failure (see failures section for details).
- Load output button, press to engage. Press again to disengage. If your battery voltages drops to low the load will automactically disengage.
- Load output LED – Green load output is on, Red is USB error.
- USB output – 5VDC, 2.4Amp.
- One of four mounting slots.
Additional Solar Panel Battery Controller Information/Warnings
- This device does not current limit the output, therefore you must ensure that you do not exceed the 10Amp output rating. If the 10Amp output is exceeded the RED error LED (#9) will flash on the front panel. The output regulator will then stop, however current will still pass through the regulator. Once the current has dropped below 10Amps the regulator will reboot.
- Maximum 150W solar panel at 12V (20-25VDC).
- Maximum 300W solar panel at 24v (40-50VDC).
- The load will automatically disengage if the battery voltage gets too low.
- The solar charger controller will automatically detect if you have connected up to a 12V or 24V battery. It will then charge appropriately at 14.4V for a 12V battery and 28.8V for a 24V battery.
Failures
THE RED ERROR LED (#9) ON THE FRONT PANEL WILL BE RED IF THERE IS A FAiLURE WITH THE OUTPUT REGULATOR.
Possible failures:
- Reverse polarity: Check that your + positive and – negative connections are correct and not reversed.
- Short circuit: Check there is not a short between the + positive and – negative connections.
- High voltage: Check the input voltage has not become too high and the regulator has turned off. Current will still be flowing.
- Low voltage: Ensure your 12V battery has sufficient charge in it before connecting. A 24V battery must be at least 16V+.
- If your 15A cable fuses are continually blowing, you are exceeding the current rating of your cables and the solar charger controller. You need to either reduce the input current or increase the size (AWG) of the cables or solar charger controller. Pro-User Electronics does sell larger 30Amp and 50Amp solar charger controllers.
Warranty
Pro-User Electronics warrants this product for a period of 2 years from the date of purchase to the original purchaser. Warranty is not transferable. Warranty covers defect against workmanship and materials only. To obtain warranty service, please return the unit to the place of purchase or authorized Pro-User Electronics dealer together with your proof of purchase. The warranty is void if the product has been damaged or not used as described in this manual. Warranty is void if a non-authorized repair has been performed. Pro-User Electronics makes no other warranty expressed or implied. Pro-User Electronics is only responsible for repair or replacement of the defective product and is not responsible for any consequential damage or inconvenience caused by the defect.
Contact information:
Tradekar Benelux BV
Ohmweg 1
4104 BM Culemborg
The Netherlands
+31(0)345470990
Info@tradekar.com
Pro-User Electronics is part of Tradekar House of Leisure Brands
Tradekar Benelux BV
Ohmweg 1
4104 BM Culemborg
The Netherlands
www.pro-user.com
Pro-User Electronics is part of Tradekar House of Leisure Brands
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>