Trosa ZN41091 LED Pir Flood Light Instruction Manual
- May 15, 2024
- Trosa
Table of Contents
Trosa ZN41091 LED Pir Flood Light
Product Information
Specifications
- Supply Voltage: 220-240 V~ 50 Hz
- Bulb Type: Non-replaceable 20W LED – 30W LED (See rating / box info)
- Class: Class I (must be connected to earth)
- IP Rating: IP54 (Protects against dust and low pressure jets of water from all directions)
- Manufacturer: Cascade Holdings Ltd
Product Usage Instructions
Installation Instructions
- If the external flexible cable or cord is damaged, it must be replaced by a qualified electrician.
- Check all parts are included and remove packaging.
- Choose a suitable location for the product.
- Securely fix the product using the supplied screws and wall plugs suitable for masonry only.
- Avoid drilling into pipes or mains cables during installation.
- Avoid placing any objects on the product.
- Ensure there is no electricity failure and all connections are secure if the product does not light up after installation.
- Disconnect from mains before maintenance or adjustment.
Cleaning Instructions
The lamp can be cleaned with a clean dry cloth. Do not immerse it in water.
Always switch off the supply before cleaning.
Manual Override Function
To switch on the light permanently using manual override function:
- While the light is switched on but not illuminated, switch it off and on twice within 6 seconds.
- The light will stay illuminated permanently after following the steps above.
FAQ
-
Q: What should I do if the product does not light up after installation?
A: Ensure there is no electricity failure and check that all connections are secured properly. -
Q: How should I clean the lamp?
A: Use a clean dry cloth to wipe the lamp. Do not immerse it in water and remember to switch off the power before cleaning.
Trosa LED Floodlight + PIR Instruction Manual READ ALL INSTRUCTIONS
Safety
- These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.
- Always organize cables and extension leads so that they will not be a trip hazard
- If the external flexible cable or cord of this Luminaire is damaged, it must only be replaced by a qualified electrician to avoid any electrical hazards.
- Check the pack and make sure you have all of the parts listed.
- Remove all packaging, wrap etc. from the product.
- Decide on the appropriate location for your product.
- IP54 product: Protects against dust and low pressure jets of water from all directions.
- Limited ingress permitted.
- Always refer to the installation drawing for the orientation of the product.
- The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other
- fixings not supplied and must be purchased.
- Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
- Never put anything on the product or hang anything on any part of this product.
- When the product does not light after installation:
-
Ensure there is no electricity failure
-
Ensure all the connections are secured
-
- Always disconnect the product from mains at least 10 minutes allowing to cool down before any maintenance or adjustment.
- CAUTION: Do not stare at the operating LED light source.
Cleaning care
- The lamp can be cleaned with a clean dry cloth. Do not immerse it in water.
- Always switch off the supply before cleaning
Parts Supplied
Tools required (not supplied)
Installation Instructions
Manual Override Function
Using the step shown below, the light can be switched on permanently by using the manual override function.
- Whilst the light is switched on but not illuminated switch the light off and on twice within 6 seconds and the light will stay illuminated permanently.
- To switch the unit back in to auto mode, switch the light off and leave for a minimum of 6 seconds and then switch the light back on. The light will then only illuminate if the PIR is triggered.
Images for illustration purposes only – Product may differ slightly from the one shown
Technical Data
- Supply Voltage: 220-240 V~ 50 Hz
- Bulb Type:
- Non-replaceable 20W LED – 30W LED (See rating / box info)
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person
- Conformity with all relevant EC and UK Directive requirements.
- Class I product, must be connected to earth.
- IP54
- Protects against dust and low pressure jets of water from all directions.
- Limited ingress permitted.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
Helpline
- If you receive this item with parts broken or missing, pleas e telephone: 0333 0050077
- Please have ready your name, address, tel. no., product reference, where purchased and parts required. An answering service is in operation outside office hours and during busy periods.
- We regret that we are unable to give advice on internal house wiring.
- Cascade Holdings Ltd, Gorse Mill, Gorse Street, Chadderton, Oldham. OL9 9R J
- EU Authorised Representative: Authorised Rep Compliance,
- Ground Floor, 71 Lower Baggot Street, Dublin, Ireland, D02P593
Read User Manual Online (PDF format)
Loading......