Josnown P9 Automatic Soap Dispenser User Manual
- May 15, 2024
- Josnown
Table of Contents
Automatic Soap
Dispenser
Introduction
Machine Structure
|
---|---
Product paramete
Model Number: P9
Rated power :1. 5W
Tum on: Touch+sensor
Sensing speed: 0.25s
Sensing distance: 0 -70mm
Dispensing: 0. 3/0.8/1. 5/2.0s (4 levels)
Bottle capacity: 400ML
N.W.:249g (not include soap)
G.W.: 287g (not include soap)
Working temperature: 5°C – 40C
Water proof: IPX5
Working humidity: 0% -85%
Accessories
TYPE -C Charging Cable
Wall Mounted Panel
Clogging Prevention Bottle (Please cut off the nozzle tip of the bottle before use)
Function
Turn ON: Press touch area, LED1 will be lighted for 2s
Turn OFF: Long press touch area for 2s, LED1 & LED4 will flash for 3s
Switch Level: Press power button, then the gear can be switched accordingly
Level Illustration:
Level 1 – LED1 lighted (Dispensing 0. 3s)
Level 2-LED1, LED2 both lighted (Dispensing 0.8s)
Level 3-LED1, LED2, LED3 all lighted (Dispensing 1. 5s)
Level 4-LED1, LED2, LED3, LED4 all lighted (Dispensing 2.0s )
Lower Battery: The led light will be flashing 5s then turn off automatically
Sensing: Put your hand to the dispensing nozzle and keep the distance range of
0-70mm, then the machine will dispense the soap you need.
Cleaning Mode: Tum on the machine and triple click the power button to start
the cleaning mode. The machine will automatically turn off the cleaning mode
after 10 seconds, or you can click the power button to turn ii off.
Note: The soap dispenser will enter a standby mode if it do not work for
a long time, no need to tum it off yourself.
Set up
-
Turn 90 degrees counterclockwise to unscrew the bottle
-
Fill with suitable liquid soap into the bottle.
-
Align the bottle mouth card position with the body card position, rotate the bottle 90 degrees clockwise, and set the bottle Sub – Installation host
Stop Sprayed out Troubleshooting
-
Cut the nozzle tip of the dredge bottle with scissors.
-
Fill the dredge with clean water.
-
Remove the plug from the hose of the dispenser.
-
Firmly insert the tip of the dredge bottle into the tube and press the bottle lightly to release the water until the water comes out from the nozzle.
Ac knowledge
-
Please fully charge the machine before use.
-
Please confirm whether the water got in the machine if the machine starts spraying, or was upside-down or tilting.
If necessary, please wipe and dry it before continuous use. -
Do not immerse the product into water or rinse it directly to avoid short circuits. It is recommended to use a wet towel to gently wipe the surface of the product when it is turned off.
-
Do not put them in a place where the kids can touch them. Persons who are physically unsound, mentally impaired, and lack relevant experience and knowledge (including children) should use under the supervision and guidance of their guardian.
-
Do not pull the power cord with wet hands and make sure the adapter and power cord are dry before charging.
-
Plug the soft rubber into the charging port to prevent water from entering.
-
Do not throw it into the fire, this product contains a built-in rechargeable battery.
-
Do not use it while charging or at high temperatures.
-
Store this product in a cool place, and keep away from direct sunlight or heat sources. Please pour out the hand sanitizer to avoid deterioration of the liquid if it is not used for a long penod of time
Prolinx Global LTD
27 Old Gloucester Street, London, WC1N 3AX,
UK
Manufacturer:
Shenzhenshi, Guangdongsheng, 518000
FAQ
Please stop using the machine if you find any abnormality or failure of our product and deal with it according to the type of failure!
Troubleshooting
-
Q: The machine suddenly self-bubbling and the indicator flashes quickly.
A: The sensor area may be covered by foam or there is something in the sensor area (0-70mm). Please tum off the machine, clean the sensor area and try again. -
Q: Why it can’t dispense when I mix shower get and water?
A: Most cleaning products are too viscous to use directly. We recommend to use foam Soap or 13-14 ratio of liquid soap to water. -
Q: The machine can’t be turned on and no response to touch area after fully charge, or the gears switch by itself.
A: There may be water on the touch area. Please wipe the touch area and try again.