TRIANGLE ELARA ACTIVE Series Bluetooth Speakers Owner’s Manual

TRIANGLE ELARA ACTIVE Series Bluetooth Speakers

CAUTION
Use the Product in the environment with the temperature Between -10°C/ 14°F and 40°C/104°F; otherwise, it may damage your product.

For the following equipment

• Product Name: ELARA Active Series LN01A speakers

• Brand Name: TRIANGLE

• Model No.: LN01A, TEB30_F, TEB30_G, TEB30_AI, TEB30_C, TEB30_AV, TEB30_AW, TEB30_AM, TEB30_AJ
  TRIANGLE Hi-Fi (E-mail: info@trianglehifi.com ) hereby declares that this ELARA Active Series,

• Model: LN01A, TEB30_F, TEB30_G, TEB30_AI, TEB30_C, TEB30_AV, TEB30_AW, TEB30_AM, TEB30_AJ is in compliance with Radio Equipment Regulations 2017 (SI 2017 No. 1206, as amended by SI 2019 No. 696).

• The full text of the UK declaration of conformity is available at the internet address: https://www.trianglehifi.com/en/uk-declaration-of-conformity/

• The RF distance between body and product is 0mm

• Bluetooth Version: Bluetooth V4.0 (Only EDR )

• Frequency Range: 2402-2480MHz 2.4GHz

• Frequency Range: 2464MHz Receiving

INSTALLATION PRECAUTIONS

Before the installation
Before making any connections, turn off the devices. Be sure to always set the active speaker switch to OFF before removing or plugging connection cables. Do not plug in the power cord before all connections are made.

Moving the device
Always remove the power cord and disconnect the cables between all components when moving the device. This will prevent a short-circuit or the damage to the plugs or connection cables.

Before turning on the device
Check one last time if all the connections are correct.

Location to avoid
Install your speakers in a temperate place and avoid humid locations or direct sunlight.

Recycling
Protection of the environment: Your products contain valuable materials which can be recovered or recycled. Take them to the appropriate collection points.

UNPACKING
Open the box, and take out the speakers and accessories. If you notice any defects in one of the elements as you unpack, please get in touch with your reseller. Before disposing of the packaging, make sure there is nothing left inside.

For LN01A :

• 1 x active speaker LN01A ELARA
• 1 x passive speaker LN01A ELARA
• 1 x remote (pull out the plastic tab from the battery compartment before use)
• 2 x protection grids
• 8 x adhesive anti-slip feet to place below the speakers
• 1 x AC power cord
• 1 x 3-meter speaker cable to link the speakers
• 1 x registration form
• 1 x user manual

For LN05A :

• 1 x active Elara LN05A speaker
• 1 x passive Elara LN05A speaker
• 1 x remote (Pull out the plastic tab from the battery compartment before use.)
• 2 x protection grids
• 8 x adhesive anti-slip feet to place below the speakers
• 8 x decoupling spikes
• 2 x pedestals
• 8 x screws
• 1 x AC power cord
• 1 x 5-meter speaker cable to link the speakers
• 1 x registration form
• 1 x user manual

ASSEMBLY OF THE LN05A PEDESTAL

Stand the speaker on the top on a nonabrasive surface. Secure the pedestal by using the screws supplied.

• On a rigid surface (wood, floor): Stick the rubber pads 2 at the 4 corners of the pedestal.
• On a soft ground (carpet, rug):  Screw the spikes 3 in the inserts of the pedestal.

POWERING

Connecting the speakers
The ELARA active speakers must be interconnected with the provided cable. (Black cable mentioning: “High performance OFC cable”). Make sure that the speaker connection polarity is correct. The red and black terminals on the passive and active speakers must be connected respectively to one another. To help with the setup, the connection cable bears the mention ‘TRIANGLE High performance OFC cable” and must be connected to the red terminal (+).

Powering on
Once you have checked the amplifier on the active speaker is set to the “OFF” position, plug the power cord into the designated input and into an AC power outlet. The speakers are then ready for use and can be turned on.

DESCRIPTION OF THE SPEAKER

1. RCA input (line/phono)

2. 3.5mm Jack auxiliary input

3. Subwoofer output

4. Optical input

5. Coaxial input

6. RCA switch (line/phono)

7. Turn: Volume control
   Press : Source selection :

8. Bluetooth

9. Line ou Phono (RCA)

10. Auxiliaire

11. Optique

12. Coaxial

13. Power switch

14. AC outlet

15. Terminal of the passive speaker

DESCRIPTION OF THE REMOTE CONTROL (V1)

1. Mute
2. Standby / Power On
3. Skip backward (Bluetooth Only)
4. Skip backward (Bluetooth Only)
5. Play/Pause a track (Bluetooth Only)
6. Source: Bluetooth
7. Source: 3.5mm Jack
8. Source: RCA (Phono/Line)
9. Source: Coaxial
10. Source: Optical
11. Resetting bass, treble and volume adjustements
12. Increasing/Reducing bass
13. Increasing /Reducing treble
14. Increasing/Reducing volume

When using the remote, always direct it towards the receiver on the front of the main speaker. The LED on the front panel blinks when the remote is being used.

DESCRIPTION OF THE REMOTE CONTROL (V2)

1. Standby / Power On
2. Mute
3. Increasing bass
4. Increasing treble
5. Increasing volume
6. Previous Track
7. Next Track
8. Play/Pause
9. Reducing volume
10. Reducing bass
11. Reducing treble
12. Reset default equalizer
13. Source selection button

When using the remote, always direct it towards the receiver on the front of the main speaker. The LED on the front panel blinks when the remote is being used.

DESCRIPTION OF THE REMOTE CONTROL (V3)

1. Standby / Power On
2. Mute
3. Increasing bass
4. Increasing treble
5. Increasing volume
6. Previous Track
7. Next Track
8. Play/Pause
9. Reducing volume
10. Reducing bass
11. Reducing treble
12. Reset default equalizer
13. Source selection button
14. Bluetooth pairing

When using the remote, always direct it towards the receiver on the front of the main speaker. The LED on the front panel blinks when the remote is being used.

CONNECTING SOURCES

The ELARA active speakers can be paired with a variety of sources. Here are the various options :

Connection via Bluetooth
This enables you to stream music wirelessly thanks to latest generation 4.0 A2DP aptX Bluetooth technology. AptX is a coding system which enables you to stream music to your Elara speakers via Bluetooth, delivering sound approaching CD-quality. The range is of about 10 meters, depending on the surroundings and obstacles within the path. Elara active speakers lets you play music from any Bluetooth-enabled sources: smartphone, tablet, computer, etc. To do so:

• Slide the power switch on the back to the ON position to activate your Elara speakers.
• Select the “Bluetooth” input using the “INPUT” button on the back of the speaker or on the remote. The blue LED indicates that the source is connected via Bluetooth.
• Press the “Bluetooth” button on your remote. The blue LED blinks, indicating that the system is seeking to connect to a Bluetooth-enabled device (smartphone, tablet…).
• When you search on your Bluetooth device (refer to the user guide if needed), the speakers should appear under the name “LN01A” or “LN05A”, you can then connect to this. Your speakers are now linked to your device and will reproduce the sound from the device. The connection will be made automatically next time you switch on your speakers if Bluetooth is selected and enabled on your device.
• If you wish to connect another device while the previous one is still connected :
  • Remote V1 & V2 : Remove Bluetooth from your previous connected device or disconnect it directly in the Bluetooth menu. The LED will flash again, a new search mode is then activated.
  • Remote V3 : Press the « BT PAIR » button.
• disable the Bluetooth connection from your formerly paired device or disconnect it directly from the Bluetooth menu. The LED will blink again, and the seeking mode will be activated.
• ACTIVE SERIES Bluetooth process allows you to change track, play and pause directly from your remote, without using the connected device.
• Your Bluetooth device now controls your speakers and you can change the volume directly from this device.

Connection via an RCA cable

The RCA input enables you to connect your Elara active speakers to your TV, CD player, turntable or any other device. To do so:

• Plug the red and white connectors into “RCA INPUT” on the back of the speaker, minding the colours, and do the same on the source.
• Select the “RCA” input using the remote or the “INPUT” button (volume button) on the back of the active speaker. (Source selecting order is indicated above the “INPUT” button.) The green LED indicates that the source is actually connected to the “RCA” input. Make sure the selector is switched to “LINE”. Your system is ready to operate.

Connecting a turntable
To plug a vinyl player, push the “PHONO IN” switch to the left for the signal to pass through the phono chain. Connect the ground wire to the dedicated screw terminal on the back of your amplified speaker and to your turntable.

Connection via a 1/8-inch (3.5mm) jack cable

The jack input – for a 3.5mm jack cable – (AUX IN) enables you to connect your speakers to many devices: smartphone, audio player, tablet, computer, television, etc. To do so:

• Plug one end of the jack connector into the “AUX INPUT” terminal and the opposite end into your device.
• Select the “3.5” input using the remote or the “INPUT” button (volume button) on the back of the amplified speaker. (The source selecting order is indicated above the “INPUT” button.) The green LED indicates that the source is actually connected to the “AUX” input. Your system is ready to operate.

Connection via an optical cable

The optical input enables you to connect your ELARA speakers to any audio device with an optical output: audio player, DVD player, television, etc. To do so:

• Plug one end of the optical cable into the back of the active speaker in the “OPTICAL” input and the opposite end into your device.
• Select the “OPTICAL” input using the remote or the “INPUT” button (volume button) on the back of the active speaker. (The source selection order is indicated above the “INPUT” button.) The green LED indicates that the source is actually connected to the “OPTICAL” input. Your system is ready to operate.

Connection via a coaxial cable
The coaxial input enables you to connect your ELARA speakers to any audio device with a coaxial output: CD player, DVD/Blu-ray player, television, etc. To do so:

• Plug one end of the coaxial cable into the back of the active speaker in the “COAXIAL” input and the opposite end into your device.
• Select the “COAXIAL” input using the remote or the “INPUT” button (volume button) on the back of the active speaker. (The source selection order is indicated above the “INPUT” button.) The green LED indicates that the source is actually connected to the “COAXIAL” input. Your system is ready to operate.

Connection of a subwoofer
The ELARA speakers include a subwoofer output allowing the connection of a subwoofer.

ARCA to 2 RCA cable (Y cable) must connect the SUB output of the ELARA speakers to the 2 LINE IN of the subwoofer. Set the subwoofer volume and cut- off frequency (Crossover) so that you get a proper sound coherence between the ELARA speakers and the subwoofer. Subwoofer sound needs to be heard without being too powerful.

BASS AND TREBLE ADJUSTMENT
Your ELARA speakers have a band equalizer that enables you to adjust the low and high frequencies as you like.

Adjusting the amount of bass
6 positions available in 2dB steps over a range between 30 and 400Hz. (-6dB, -4dB, -2dB, 0dB, +2dB, +4dB, +6dB). The factory setting defaults to 0dB. The low-frequency output will increase or decrease each time the remote control is pressed.

Adjusting the amount of treble
6 positions available in 2dB steps over a range between 2 and 30KHz. (-6dB, -4dB, -2dB, 0dB, +2dB, +4dB, +6dB). The factory setting defaults to 0dB. The high-frequency output will increase or decrease each time the remote control is pressed. When the speaker goes on standby, the settings will be stored for the next use. To restore the factory presets, you just need to press the “RESET” button on the remote.

AUTO STANDBY FEATURE
If no signal is received for 30 minutes, the speakers will automatically switch to standby. To exit the standby mode, simply switch the speakers back on with the remote (see page 21).

ELARA SPEAKERS

Technical specifications|

ELARA LN01A

|

ELARA LN05A

---|---|---

Type

|  Active speakers|  Active speakers
Driver diameters| 13 cm

5″

| 2 x 13cm 2×5″
Sensibilité enceintes Sensitivity|

89 dB/m

|

90 dB/m

Bandwidth (+/- 3dB)|

56 Hz – 22 KHz

|

47 Hz – 22 KHz

Power handling|

2 x 50W

|

2 x 80W

Inputs| RCA, AUX, Optical, Phono, Bluetooth 4.0 A2DP aptX| RCA, AUX, Optical, Phono, Bluetooth 4.0 A2DP aptX
Output| Subwoofer| Subwoofer

Dimensions

| 165 x 235 x 291 mm

6.49 x 9.25 x 11.46 inches

| 165 x 263 x 900 mm

6.49 x 10.35 x 35.43 inches

Dimensions with pedestal|

–

| 230 x 290 x 921 mm

9.05 x 11.41 x 36.25 inches

weight| 9,5 kg

19.84 lbs

| 27,3 kg

60.18 lbs

**Gross weight (pair)**| 11,2 kg

24.25 lbs

| 31,3 kg

68.34 lbs

SAFETY INSTRUCTIONS

WARNING : Read carefully all the safety instructions before using the device.

• Keep these safety instructions for future reference.
• Do not use this apparatus near water or liquid.
• Only clean with a dry and soft cloth.
• Make sure the openings (vents) on the device are not blocked.
• Do not install near any heat sources such as radiators, stoves, or any other apparatus (including amplifiers) that produce heat.
• Only use accessories specified by the manufacturer.
• Be sure that the stand/table/furniture is strong enough to support the apparatus (stand, shelf, furniture…).
• Protect the power cord from being walked on or pinched, particularly at the plugs, and protect the connector where it exits from the apparatus.
• Unplug the apparatus during lightning storms or when it’s unused for long periods of time.
• The plug of the apparatus must fit with the outlet. Never modify the plug in any way. The apparatus should be connected to a mains socket outlet with protective earthing connection.
• Refer to your authorized TRIANGLE dealer or qualified service personnel if the apparatus is damaged in any way. For example, if the power cord or the wall outlet is damaged, liquid has been spilled or objects have fallen on the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARRANTY

Thanks for buying a TRIANGLE product.
We want you to enjoy your purchase to the fullest. The first step is an easy registration of your product. By doing this, you will benefit from helpful tips, products support, special offers and a 1 year extension warranty.

Online registration
Register your product easily online at the following address:
http://register.trianglehifi.com/

Documents / Resources

| TRIANGLE ELARA ACTIVE Series Bluetooth Speakers [pdf] Owner's Manual
ELARA ACTIVE Series Bluetooth Speakers, ELARA ACTIVE Series, Bluetooth Speakers, Speakers
---|---

References

• Triangle Hifi (@trianglehifi) • Instagram photos and videos
• TRIANGLE - High End Hifi Speaker Manufacture
• UK declaration of conformity - TRIANGLE Hifi

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>