SCHNEIDER SCIM3222 Ice Maker Instruction Manual
- May 15, 2024
- Schneider
Table of Contents
ICE MAKER
SCIM3222
INSTRUCTION
MANUAL
IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE FOR FUTURE REFERENCE.
IMPORTANT SAFETY WARNINGS AND TIPS
When using an electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury, including:
-
Read all instructions before using the device.
-
CAUTION: Keep ventilation openings in the appliance enclosure or in the framing unobstructed.
-
CAUTION: Do not use mechanical devices or other means to speed up the defrosting process other than those recommended by the manufacturer.
-
CAUTION: Do not damage the refrigeration circuit.
-
CAUTION: Do not use electrical appliances inside the food storage compartment, unless they are of the type recommended by the manufacturer.
-
CAUTION: Filling only with drinking water.
-
WARNING: When positioning the appliance, make sure that the power cord is not pinched or damaged.
-
WARNING: Do not place mobile bases, multiple sockets or portable power supplies on the back of the device.
-
This product is intended for indoor and household use only.
-
Remove all packing materials and carefully check that your ice maker is in good condition and that the ice maker, power cord and plug are undamaged.
-
Before using the ice maker for the first time, wait 2 hours after setting it up and leave the lid open transparent at least 2 hours.
-
Check that the voltage is within the voltage range indicated on the label and make sure that the grounded outlet is in good condition.
-
If the power cable is damaged, it must be replaced by the manufacturer, its after-sales service or similarly qualified persons in order to avoid a hazard.
-
Do not move this product or tilt it at an angle of 45°.
-
To protect against risk of electric shock, do not pour water over cord, plug and vent. Do not immerse the device in water or any other liquid.
-
Unplug the appliance after using it or before cleaning it.
-
Keep the device 8 cm away from other objects to ensure good heat dissipation.
-
Do not use accessories that are not recommended by the manufacturer.
-
This device can be used by children aged at least 8 years and by people with reduced physical, sensory or mental capacities or without experience or knowledge, if they are properly supervised. s or if instructions relating to the use of the appliance in complete safety have been given and if the risks involved have been apprehended. Children should not play with the device. Cleaning and user maintenance shall not be carried out by children without supervision.
-
Do not use the appliance near flames, hot plates or stoves.
-
Do not turn on the power button frequently (make sure you have at least 5 minutes apart) to avoid damaging the compressor.
-
Sheet metal or other electrical objects must not be inserted into the device to avoid fires and short circuits.
-
Do not use outdoors.
-
Never clean with scouring powders or hard instruments.
-
Please keep the instruction manual.
-
Do not store explosive substances such as aerosols containing flammable propellants in this device.
-
WARNING : During the positioning the appliance, make sure that the power cord is not pinched or damaged.
-
WARNING: Do not place movable socket outlets or portable power supplies on the back of the device.
-
Children between the ages of 3 and 8 are allowed to load and unload refrigeration appliances.
-
To avoid contamination of food, it is necessary to respect the following instructions:
– Opening the cover for a long time is likely to cause a significant increase in the temperature of the compartments of the device.
– Regularly clean surfaces likely to come into contact with food and accessible drainage systems.
– Clean the water tank if they have not been used for 48 hours; ; otherwise, if the appliance has one, rinse the distribution system connected to a water distribution network thoroughly if water has not been drawn for 5 days.
– If the refrigeration appliance remains empty for a long time, turn it off, defrost it, clean it, dry it, and leave the lid open to prevent the development of mold inside the appliance. -
Refrigerant and insulation blowing gas is flammable, when disposing of the appliance, do so only at an authorized waste disposal centre. Do not expose to flame.
-
This appliance is intended for household use only. Any other use is improper, among other things, it must not be used:
– in kitchens reserved for staff in shops, offices and other professional environments;
– in farms, lodges, bed and breakfasts;
– by customers in hotels, motels and residential environments
– in catering and similar applications.
Hazard; fire hazard/flammable materials
WARNING: When positioning the appliance, make sure that the power cord is
not pinched or damaged.
The refrigerant gas contained in the circuit of this appliance is isobutane (R
600a), a lowpolluting but flammable gas. When transporting and installing the
appliance, take care not to damage any part of the refrigeration circuit.
With regard to the installation, handling, cleaning and disposal of the
device, refer to the following chapters of the user guide.
Suitable to come into contact with foodstuffs.
IMPORTANT
It is forbidden to replace the power cord yourself. If damaged, it should be
repaired by the local distributors service department, the manufacturer or
similarly qualified persons.
If the device has been dropped, ask a qualified professional to inspect it
before using it again. Internal damage can cause accidents.
For any type of problems or repairs, contact the after-sales service of local
distributors, the manufacturer or persons with similar qualifications to
prevent any possible risk.
Disposal and Environmental Responsibility:
In order to protect the environment, we encourage you to dispose of the
device. You can contact local authorities or recycling centers for more
information.
Read this manual carefully before using the product.
This product complies with the requirements of Directive 2014/35/EU (which
replaces Directive 73/23/EEC amended by Directive 93/68/EEC) and 2014/30/EU
(replaces Directive 89/336/EEC) .
Characteristics of your product
1. Transparent window
2. Front lid
3. Product body
4. Control Panel
5. Back lid
6. Air inlet| 7. Infrared sensor for full ice detection
8. Ice catcher
9. Ice cream basket
10. Silicone stopper
11. Ice shovel
12. Air outlet
---|---
Control panel
A. “Full” Ice Bin Indicator
B. Operation indicator
C. Water shortage indicator
D. On/off button| E. Small ice cube size
F. Choice of size Small/large ice cube
G. Large ice cube size
---|---
Before first use
-
Unpack the appliance, then check that all accessories, including the ice basket, ice scoop, etc., are present. Please contact customer service if any accessories are missing.
-
Please ensure the ice cream maker is level and placed on a stable table or platform to prevent malfunction.
-
The tilt angle of the ice maker housing should not exceed 45° during transport or use. Do not turn the ice maker upside down. This could cause the compressor or refrigeration system to malfunction. Please allow compressor fluids to stabilize after moving or transporting the ice maker.
Before using the ice cream maker for the first time, please wait 24 hours for the unit to be level and properly adjusted. -
The device should be placed on a dry, horizontal surface with sufficient ventilation, away from corrosive gases and heat sources such as ovens and radiators. Leave approximately 6 inches (15 cm) of space on all sides of the ice maker for proper ventilation.
-
Do not fill the water tank with hot water. This can damage the ice maker.
Better to fill the water tank with water at room temperature or lower. -
Do not use the device in a very cold environment (temperature below 5℃).
-
Clean the appliance following the operations in the “CLEANING AND MAINTENANCE” chapter before using it.
-
When adding water to the water tank, make sure the silicone plug at the bottom of the machine is firmly inserted so that the water does not leak out.
-
Do not use water containing impurities or with solid particles, pure water is recommended.
-
Please keep the ice cream maker away from direct sunlight, heat or radiation. Place the ice maker horizontally and you will get a space of 15 cm between the sides and the back.
-
The ice maker must be placed in an appropriate outlet for power supply.
Using your ice maker
Use the ice maker (indoor)
- Open the front cover, take out the ice basket and fill the water tank. (water level is recommended below the maximum water level)
- Put the ice basket back and make sure it is installed securely, if not, please gently press the bottom to put it in place.
- Push the button on the control panel, choose the size of ice cubes you need. Then press the “ ” to start the ice making circulation.
- The first ice production cycle lasts approximately 9 minutes. It depends on the ambient temperature, the size of the ice cube also depends on the water temperature and the ambient temperature.
- After starting the ice maker, the water level in the water tank should be checked frequently. If the water level is too low, the water pump can not pump water, the ice maker will automatically stop, the indication of lack of constant brightness to indicate the lack of water, at the same time the buzzer starts beeping, at this time, the water tank should be filled below the maximum water level, then press “ON/OFF” to restart ice making.
- If the ice bucket is full of ice, the ice maker will automatically stop ice making and the full indicator constant brightness. At the same time, the buzzer starts to beep, when the ice position is lower than the infrared detection position, the machine starts to work again.
- Stop/cancel ice making. To stop or cancel ice making, press the “ON/OFF” button to stop ice making. And will be in sleep mode.
- It is recommended to change the water once every 24 hours to keep the water clean. If the ice maker is not used for a long time, please empty the water inside the water tank and wipe the water tank, at the same time, please also cut off the power supply and remove the socket plug.
CLEANING AND MAINTENANCE
Before using the ice cream maker, it is highly recommended to thoroughly clean the entire machine.
- Take out the ice bucket.
- Open the silicone plug at the bottom of the machine body and drain the water inside the water tank.
- After diluting the soft cloth with neutral cleaner, clean the water tank and the external part of the machine.
- Rinse the interior with clean water.
- Install the silicone stopper at the bottom of the machine and equip that it is installed securely.
- Does not use chemicals, such as alcohol
- Do not use steel balls, hard brushes and other tools to clean the surface of the product.
- Do not expose the product power line and packaging accessories to direct sunlight.
- Do not tilt the machine more than degrees or turn it upside down, otherwise the cooling system may not work properly.
- The machine has not been used for a long time, the water inside the water tank should be drained, and the water tank should be wiped dry.
SELF-CLEANING FUNCTION
- When the ice maker works normally, press the power button for 3 seconds, the machine will be in self-cleaning mode (the pump starts working, pumping water from the water tank to the ice maker, works continuously for about 10 minutes, then automatically into sleep mode.) You can also press the power button to exit the self-cleaning function and go into sleep mode.
Repair
| Situation | Reason |
|---|
When the ice maker first starts, the water pump pumps for 5 seconds, then
stops for 5 seconds, then pumps again for 5 seconds, then stops again for 5
seconds, then sucks the water continuously for 3 minutes.| Exhausts air from
the water suction pipe to prevent it from producing water without water.
After connecting to power and the machine is turned on, ice making| This
detects whether the ice box is horizontal.
During ice making, the infrared light is blocked, the machine will produce ice
normally, after an ice making cycle, the infrared light is still blocked, and
then displays Full.| This is to eliminate the illusion of full ice caused by
infrared misjudgment
Failure analysis and processing
| Failure | Cause | Solution |
|---|---|---|
| The power light is not apparent | The power plug is not well connected or there | |
| is no electricity in the plug. | Plug in the power plug correctly in the socket |
and make sure it is connected separately.
On the control panel, the red “bin full” light is on, but there is no ice in
the cooler| 1. The infrared sensor adheres to a foreign body.
2. The infrared sensor is broken.| 1. Please cut off the power supply of the
product and remove the foreign body stuck to the infrared sensor.
2. Please stop using the product and contact the supplier and customer
service and repair it by the maintenance of the service provider.
On the control panel, the water shortage indication is on but there is a lot
of water in the tank| 1) Maybe the pump is broken.
2) The water supply system is blocked by impurities.| Please stop using the
product and repair it with the designated repair service provider .
Ice is mixed with impurities| There are impurities in the water tank .| Please
rinse the inside of the water tank.
The ice has a smell| Due to the quality of water or ice produced the first
time after purchase.| After several uses, the smell will disappear.
The “low water” light is on.| 1. Lack of water.
2. The bottom of the water tank is blocked.| Stop ice making, add water and
press “ON/OFF” to start ice making again.
The “bin full” light is on.| 1. There is too much ice in the ice basket.
2. The black sensor to indicate that the bin is full is broken, there is no
ice, but the “Full” light is on.| 1. Take the ice from the ice cube basket.
2. Please stop using the product and contact your supplier and have it
repaired by a designated repair service provider.
The “basket full” light flashes.| The ice catcher that allows them to fall
into the ice basket is stuck.| 1. Press the “ON • OFF” button to stop ice
making.
2. Please stop using the product and contact your supplier and have it
repaired by a designated repair service provider.
Ice cubes stick together.| 1. The ice making cycle is too long.
2. Too many coins are submerged in the ice cube tray.
3. The water temperature inside the water tank is too low.| 1. Stop ice
making, after the ice melted, restart the ice making machine.
2. Adjust the evaporator.
3. Replace the water inside the water tank, the water temperature is
preferably between 5 and 32°C.
The ice is full but the light is not on.| The machine is in a position with
strong light, it affects the detection of infrared light.| Move it to a darker
place.
The machine works but does not make ice cream.| Compressor is in Protection or
“Refrigerant Leak” Mode. o| Turn it on and off consecutively
There may be poor contact at plug connection uncle compressor does not work,
wait 30 minutes and the machine will work normally. If after more than 30
minutes, the ice maker still does not start, please stop using the product and
contact your supplier and repair it by designated repair service provider.
Characteristics:
Type of climate: SN/N/ST
Voltage: 220-240 V ~
Class: I
Frequency: 50Hz
Power: 100 W
Refrigerant: R600a (26 g)
Net weight: 8.5 kg
Dimensions of the device: 360 x 240 x 320 mm
The operating temperature of this ice machine is 10-38 degrees Celsius
Note: The ambient temperature range limit values for the climatic classes for which the refrigeration appliance is designed and the fact that internal temperatures can be activated by factors such as location of the refrigeration appliance, ambient temperature and how often the doors are opened, the setting of any temperature control device may need to be changed to take these factors into account, if necessary.
ATTENTION
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or a similarly qualified person in order to avoid a hazard. fill
with potable water only. It is normal for the compressor and condenser surface
to reach temperatures between 70°C and 90°C during operation and for the
surrounding areas to be very hot.
Due to rapid freezing, ice cubes may appear “cloudy”
This is air trapped in the water and will not affect the quality or taste of
the ice cream.
Children should be supervised to ensure that they do not play with the device.
Do not submerge in water.
- WARNING- ensure that the ventilation openings, in the appliance enclosure or in the built-in structure, are not obstructed.
- WARNING- do not use mechanical devices or other means to speed up the defrosting process, other than those recommended by the manufacturer.
- ATTENTION- do not damage the refrigeration circuit.
- WARNING- do not use electrical appliances inside the food storage compartments, unless they are of the type recommended by the manufacturer.
If this logo is affixed to the device, it means that it must be disposed of in
accordance with Directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE). Any hazardous substance contained in electrical or
electronic equipment can have harmful effects on the environment and health
during its recycling. Consequently, at the end of the appliance’s useful life,
it must not be thrown away with unsorted municipal waste.
As the end consumer, your role is essential to ensure the reuse, recycling or
any other creation of value for this appliance. Several collection and
recovery systems set up by your local authorities (recycling centers) and
distributors are available to you. It is your responsibility to use these
devices.
The warranty does not cover wear parts of the product, or problems or damage
resulting from:
- Surface damage due to normal wear of the product;
- Defects or deterioration due to contact of the product with liquids and due to corrosion caused by rust or the presence of insects;
- Any incident, abuse, misuse, unauthorized modification, disassembly or repair;
- Any improper operation for maintenance, use not in accordance with the product instructions or connection to an incorrect voltage;
- Any use of accessories not supplied or approved by the manufacturer.
The warranty will be void if the nameplate and/or serial number of the product is removed.
This product is imported by: SCHNEIDER CONSUMER GROUP
12, rue Jules Ferry, 93110 Rosny-sous-Bois, FRANCE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>