COMBAT WL1 Tactical Flashlight User Manual

COMBAT WL1
TACTICAL FLASHLIGHT

User Manual

Technical Parameters

candela
| 1meter
| IP68

Note:
According to the ANSI/PLATO FL1 standard, the above specifications are from the results produced by private laboratory testing using the included 18650-3400mAh battery under the temperature of 21±3°C and humidity of 50% – 80%. The true performance of this product may vary according to different working environments and the actual battery used.
*The high lumen output is measured in total of runtime including output at reduced levels due to temperature or protection mechanism in the design.

Product Features

• 1600 lumens maximum output; 473 meters maximum beam distance.
• The light source is vertically structured with one Luminus SFT40 LED, which is designed for effective heat dissipation and high bright output with a lifespan of 50,000 hours.
• Tactical tail switch provides one handed momentary or constant on.
• Three operation modes: Tactical/Duty/Daily Mode.
• OPTICS tempered glass lens with an anti-reflective coating for better light transmittance.
• Made of aerospace-aluminum alloy for durable wear.
• House with premium type HAIII hard-anodized anti-abrasive finish.
• With anti-reverse circuit design to prevent damage to the circuit caused by reverse battery installation.

Operating Instruction

Tactical Tail Switch
The tail switch is placed at the end of the flashlight for instant activation.

On/Off

• Press the tail switch halfway down without the sound of a click to turn on the light momentarily and silently, release to turn off.
• Fully press down the tail switch with the sound of a click to turn on the light constantly, press again to turn off.

Momentary On/Off

Constant On/Off
Operation Mode:

1. Tactical mode with high lumen output only.
2. Duty mode with high and medium lumen output.
3. Daily mode with high, medium and low lumen output.

Note:
The three modes will be activated in order from Tactical mode to Duty mode and then to Daily mode.

Mode Switching:
Instruction:
Quick halfway press the tail switch 9 times without sound of click, and hold it at the 9th time for one second till the light is flashing. When flashing is completed, then press down the tail switch completely to lock the current mode.

• If the light is flashing only 1 time with high light, then it goes into Tactical mode.
• If the light is flashing 2 times with medium light, it goes into Duty mode.
• If the light is flashing 3 times with low light, it goes into Daily mode.

Note:

• You can not switch Tactical mode directly to Daily mode, you need to switch to Duty mode, and then switch from Duty mode to Daily mode.
• If you switch from one mode to another mode, you need to repeat the instruction.
• The times of light flashing indicate the mode.
• If the light is not flashing, repeat instruction until you see the light flashing.

Output Switching
Note: Either Duty mode or Daily mode can switch the output as the Tactical mode has high lumen output only.

• In Duty mode, there are medium output and high output. Quick press the tail switch halfway 2 times and press down the tail switch completely to lock the current output, and repeat the process to the other output in Duty mode.

Switch the output

• In Daily mode, there are low output, medium output and high output. Quick press the tail switch halfway 2 times and press down the tail switch completely to lock the current output, and repeat the process to switch to the other two output.

**Switch the output

** Intelligent Memory Circuit

The light memorizes the last selected output when it is turned off or powered off. When turn on again, it works with the memorized output.

Battery Specifications

**** 18650 Li-ion batteries are powerful cells designed for commercial applications and must be treated with caution and handled with care. Only use quality batteries with circuit protection will reduce the potential for combustion or explosion. Cell damage or short circuiting are potential risks the user assumes.

Battery Replacement

Unscrew the light tail cap and insert the battery with the anode side (+) towards the light head, then screw the light tail cap back on.

**** Intelligent Overheat Protection

The light will accumulate a lot of heat when used on high lumen output levels for extended periods. When the light reaches a temperature of 60°C or above, the light will automatically step down a few lumens to reduce the temperature. When the temperature drops below 60°C, it will then allow the user for the re- selection of high light lumen output.

**** Usage and Maintenance

• Disassembling the sealed head can cause damage to the light and will void the warranty.
• Good quality battery is highly recommended.
• If the light will not be used for an extended period, take out the battery, otherwise the light could be damaged by electrolyte leakage or battery explosion.
• Unscrew the light tail cap or take out the battery to prevent accidental activation during storage or transportation.
• Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring with an approved spare．
• Periodic cleaning of electrical contacts improves the light’s performance as dirty contacts may cause the light to flicker, shine intermittently or even fail to illuminate.

Below are reasons to fail to illuminate:
A: The battery is running low.
Solution: Replace battery (Ensure battery is placed correctly according to manufacturer’s instructions).
B: The electrical contacts of the light or battery are dirty.
Solution: Clean the contacts with a cotton swab soaked in rubbing alcohol.
If the above methods don’t work, please contact us.

Product Size & Weight

Size: 140.5×32.5×23.7mm.
Weight: 107.6g (excluding battery).

Included

1. Flashlight*1
2. Lanyard*1
3. Spare O-ring*2
4. Green Decoration Ring*1
5. Grey Decoration Ring*1
6. User Manual*1

Warning

• This flashlight is a high-intensity lighting device capable of causing eye damage to the user or others. Avoid shining the flashlight directly into anyone’s eyes.
• This flashlight will accumulate a lot of heat when used for extended periods, resulting in high temperature of the flashlight shell. Pay attention to safe use to avoid scalding.
• All information provided in this manual is subject to change without prior notice.
• Keep out of reach of children.

Made In China

Documents / Resources

| COMBAT WL1 Tactical Flashlight [pdf] User Manual
WL1 Tactical Flashlight, WL1, Tactical Flashlight
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>