JOEL S ANTIQUES B07Y8SKZHG Heavy Steel Hidden Bracket Instruction Manual
- May 15, 2024
- JOEL S ANTIQUES
Table of Contents
Joel’s Antiques & Reclaimed Decor TOGGLER® Plastic Toggle Anchors
Heavy Steel Hidden Bracket
Instruction Manual
Installation Directions
NOTE: Bracket must be screwed to wood studs. No anchors!
TOOL LIST
– Drill/Drill Driver
– #2 Square Bit
– Pencil and Level
– Stud Finder
PLEASE read directions thoroughly before installing
- Mark a small spot on the wall where you want the center of the shelf to be. (Figure A) Find and mark the studs in the wall. Install the bracket to the studs using the 2 ½” pan head screws in the top row for shelves that are 10” or 12” deep. The 2” pan head screws go in the bottom row, one screw per stud (smaller holes). For 6”, 7” and 8” deep shelves use 2” screws in both rows. Do not over tighten or the bracket will indent into the wall. (Figure B)
- Slide the shelf onto the bracket. (Figures A & C) The circles on the top of the bracket are thinner metal and must line up with the predrilled holes in the top of the shelf. Otherwise you won’t be able to drill through.
- Push the shelf tight to the wall with the pre-drilled holes on top of shelf. Install the 1¼” taper head screws into the pre-drilled holes.
Screws should be flush with the top, no deeper. (Figure D)
❑ 18” …………… 1 set of screws toward the center of bracket into stud, one anchor
on each side.
❑ 24”–30” …….. 2 sets of screws into studs — or 1 in center with an anchor on
each side
❑ 36”–54” …….. 2–3 sets of screws into studs
❑ 60” …………… 3 sets of screws into studs
❑ 72” …………… 4 sets of screws into studs
Recommended| 18”–30” shelf………..30#
24”–30” shelf………..30#
---|---
Weight| 36”–54” shelf………..45#
Capacity| 60”–72” shelf………..50#
Installation Information
Instructions
-
Drill a 5/16″ diameter hole. Fold anchor in middle.
Note: Use a 3/8″ drill in very hard materials. -
Insert anchor in hole and tap flush. Only 3/4″ clearance needed behind wall. Only 1/2″ clearance for the TA anchor.
-
Insert key to pop anchor open behind hollow wall or ceiling (not necessary for thick or solid walls). Do not hammer key.
Remove key. -
Place item over anchor. Insert screw and tighten until flush with item—then stop. Do not overtighten.
Note: Only the threaded portion of the screw (TL) should be in the anchor itself; any unthreaded shank portion of the screw (S) may be in the fixture or item being anchored, but not in the anchor.
Installation Data
Size Selection Chart
Wall Anchor| Fully Toggled| Wedge| Expansion Anchor|
Screw Size Range| **Drill Bit Diameter***
---|---|---|---|---|---
| | | |
| T = 3/8″-1/2″| T > 1/2″| X = 1-1/4″| D = #6-#14
TL = 1-1/4″
L = 1-1/4″ + S| Ø = 5/16″
https://www.youtube.com/watch?v=bRJjVpwjgJM
IF YOU HAVE ANY ISSUES OR QUESTIONS PLEASE CALL OR EMAIL.
920.265.1934
joelsantiques@gmail.com
If you have issues finding the studs, we highly recommend this stud finder:
Precision Sensors ProFinder 5000+ Professional Stud Finder with built-in
bubble level and ruler. You can find it on Amazon for around $40. They also
have them at Menards. It is super easy and really does work. It’s worth every
penny. It is the one shown in Figure B.
Joel’s Antiques & Reclaimed Decor, LLC © Joelsantiques®
U.S. Patent No. 9,163,415 REV 3/23
920.265.1934 | joelsantiques.com |
joelsantiques@gmail.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>