Ansell LIGHTING Blacksmith 3 Asymmetrical LED Floodlight Installation Guide

May 15, 2024
Ansell LIGHTING

Installation Instructions
Product Code:
[AKAR/1/]

Warranty Information

For warranty details please contact your local representative or visit our website: www.anselluk.com
It is highly recommended that all Ansell luminaires are installed / maintained by a fully qualified electrician and wired in accordance to the latest IEC standards or national equivalent.
Mains power must be switched off during any installation or maintenance.
Should the product fail during the warranty period, Ansell will repair or replace the product in question.
Ansell do not accept any responsibility for any installation costs associated to the replacement of this product.
Please Note – The warranty period shall be null and void in the following circumstances:
Failure by the installer, end user or any third party to exercise caution to protect any covered product or part from outside damage, adverse temperature, humidity conditions, fluctuations in the electrical system or physical abuse as well as failure related to poor workmanship in the installation of the products or parts. Inability to provide correct product information. Any questions or concerns with the product, please contact your local representative.”

Ansell LIGHTING Blacksmith 3 Asymmetrical LED Floodlight - Figure
1Ansell LIGHTING
Blacksmith 3 Asymmetrical LED Floodlight - Figure 2

Packing List

Safety Rope| 1 PCS

Physical Dimensions (Unit: mm/inch)

Mounting

100W/150W
Mounting height of the lamp should not exceed 15m.
Recommended screw size: M12 Rotation angle
When adjusting the angle, please hold the lamp body by hand to prevent it from falling.
Ansell LIGHTING Blacksmith 3 Asymmetrical LED Floodlight - Figure
6

Safety rope installation

Ansell LIGHTING Blacksmith 3 Asymmetrical LED Floodlight - Figure
7 DMX512 Control
Factory default mode for DMX control :
Default address is the same for each luminaire. Take RGBW version for example, there are 4 addresses for each luminaire, that is address 1 for R; 2 for G; 3 for B; 4 for W. When turn on the luminaire, the four colors light up together without flashing if no input signal is detected about 10 seconds later.Ansell LIGHTING Blacksmith 3 Asymmetrical LED Floodlight - Figure
8 Please connect a signal amplifier every 100 meters or every 32 lights.
35W 100W/150W

  • It is recommended to add 0.25W/1200 DMX Termination Resistor at the end of each string of luminaires. SS-960RDM(Optional)
    The DMX controller needs to be purchased separately. We suggest buy our SS- 960RDM controller if you need to change the DMX address settings.Ansell
LIGHTING Blacksmith 3 Asymmetrical LED Floodlight - Figure
13 Signal Amplifier(Optional)
    It is suggested to connect a signal amplifier every 100 meters or every 32 lights, which can improve the signal stability.
    If RDM controller is used instead of DMX512 controller, the signal amplifier must be compatible with RDM controller, better to purchase from us directly.
    Signal line reversed connection will cause following defects:

    1. The luminaire is not controlled.
    2. The luminaire keeps flickering.Ansell LIGHTING Blacksmith 3 Asymmetrical LED Floodlight - Figure 14

DALI Blutooth (CASAMBI) Casambi app operation method
Casambi app is easy to use. Follow these simple steps.

  1. Download the app from Apple App Store or Google Play Store.
  2. Turn on your Casambi enabled luminaires.
  3. Open the app.
  4. Casambi app will automatically find all Casambi enabled luminaires that are switched on.
  5. Tap on the ‘Take all luminaires into use’.
  6. Casambi app will automatically add all luminaires to one network and open the ‘Luminaires’ tab.

Visor Installation (Optional Accessories)

Visor Dimensions (Unit: mm/inch)

Product Specifications 35W 100W 150W
Input Voltage 100-240VAC / 220-240VAC
Power Frequency 50 / 60 Hz
Outlook Dimensions 219.5x330x100mm
(8.64″x12.99″x3.94″) 450x452x160mm

(17.72″x17.79″x6.30″)
Luminaire Net Weight| 3.7±0.3kg
(8.15±0.66Lbs)| 10±0.3kg
(22.04±0.66Lbs)
Projected Area| 0.04m2(0.35ft2)| 0.12m2(1.12ft2)
Working Temperature| -30°C to +50°C(-22°F to +122°F)
Storing Temperature| -40°C to +70°C(-40°F to +158°F)
Ansell Electrical Products
Unit 6B, Stonecross Industrial Park, Yew Tree Way, Warrington, WAS 3JD| Ansell (Sales & Distribution)
Unit 2, M2 Business Park, Duncrue Street,
Belfast, BT3 9AQ| Ansell (Sales & Distribution) Republic of Ireland Limited
Unit G1, Block G, Calmount Park, Calmount Avenue Dublin 12, D12 TH56
---|---|---

www.anselluk.com
Warrington Tel: +44 (0)1942 433333 Belfast
Tel: +44 (0)2890 773750 International
Tel: +44 (0)1942 433343 Spain
Tel: OO 34 938 005642Ansell LIGHTING Blacksmith 3 Asymmetrical LED
Floodlight - Icon 2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals