hansgrohe 24240XXX Shower Column Including Thermostat Instruction Manual
- May 15, 2024
- hansgrohe
Table of Contents
Instructions for use
Assembly instructions
Pulsify Showerpipe 260 2jet
24240XXX
Pulsify Showerpipe 260 2jet Eco
24241XXX
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
The arm of the shower head is intended only to hold the shower head. Do not
load it down with other objects!
Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as
your eyes). An adequate distance must be kept between the shower and you.
The product may not be used as a holding handle. A separate handle must be
installed.
The hot and cold supplies must be of equal pressures.
Installation Instructions
- Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
- The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
- The plumbing codes applicable in the respective countries must be observed.
- The installation dimensions stated in these installation instructions are ideal for people of approximately 1800 mm in body height. The dimensions can be altered if required. In this case, pay attention to the fact that a change of installation height will also change the minimum height, and that the altered mounting dimensions must be taken into consideration.
- During installation of the product by qualified trained personnel, make sure that the entire fastening surface is even and smooth (no protruding seams or tile offset), that the finish of the wall is suitable to apply the product and has no weak points.
- The premounted dirt collection screen must be used to prevent dirt from entering through the pipes. Dirt entering can affect the function and/or lead to damage to the functional components of the fitting. Hansgrohe will not be held liable for any resulting damage.
- The product is not designed to be used with steam baths!
- If required, the bottom part of the pipe between the fixture and the shower head can be shortened with a fine-toothed saw.
Special information for UK
If installing this product with a pump, please be aware that it has to have
negative head switching. This product will not function with a positive head
pump.
Technical Data
| Operating pressure: | max. 1 MPa |
|---|---|
| 24240XXX Recommended operating pressure: | 0,13 – 0,5 MPa |
| 24241XXX Recommended operating pressure: | 0,17 – 0,5 MPa |
| Test pressure: | 1,6 MPa |
| Hot water temperature: | (1 MPa = 10 bar = 147 PSI) |
| Centre distance: | max. 60°C 150±12 mm |
| Connections G 1/2: | cold right – hot left |
| Thermal disinfection: | 70°C / 4 min |
- Safety against backflow
- The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
max.=42° c Safety Function
The desired maximum temperature for example max. 42°C can be pre-set thanks to the safety function.
Adjustment
After the installation, the output temperature of the thermostat must be checked. A correction is necessary if the temperature measured at the output differs from the temperature set on the thermostat.
Maintenance
- The check valves must be checked regularly according to EN 806-5 in accordance with national or regional regulations (at least once a year).
- To guarantee the smooth running of the thermostat, it is necessary from time to time to turn the thermostat from total hot to total cold.
Dimensions
Flow diagram
- Overhead shower
- Hand shower
Spare parts
XXX = Colors
000 = Chrome Plated
140 = Brushed Bronze
670 = Matt Black
700 = Matt White
Special accessories (order as an extra)
tile-matching-disk #94517000
Cleaning
www.hansgrohe.com/cleaning-recommendation
http://www.hansgrohe.com/cleaning-recommendation
Cleaning recommendation / Warranty / Contact
Just clean: simply rub over the spray nozzles to remove lime scale.
Operation
To empty the overhead shower after use, hold it in a slightly inclined position.
close| hot| cold
| Fault | Cause | Remedy |
|---|---|---|
| Insufficient water | – Supply pressure inadequate | – Check water pressure (If a |
pump has been installed check to see if the pump is working).
– Regulator filter dirty| – Clean filter in front of the mixer and on the MTC-
thermo cartridge
– filter insert shower dirty| – Clean filter insert between shower and hose
Crossflow, hot water being forced into cold water pipe, or vice versa, when
mixer is closed| – Backflow preventers dirty or leaking| – Clean backflow
preventers, exchange if necessary
Spout temperature does not correspond with tempera- lure set| – Thermostat has
not been adjusted| – Adjust thermostat
– Hot water temperature too low| – Increase hot water temperature to 42 °C to
60 °C
Temperature regulation not possible| – thermo cartridge calcified| – Exchange
thermo cartridge
Safety stop button not operating| – Spring defective| – Clean spring and/or
button, exchange if necessary
– Button calcified
Instantaneous heater didn’t work with thermostat| – Filters are dirty| – Clean
the filter / exchange filter
– check valve hasn’t moved back| – Exchange check valves
Shower drips continuously| – Dirt or sedimentation on valve seat, shut-off
unit damaged| – Exchange shut-off unit
Assembly
Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach · Telefon +49 (0) 78
36/51-1282 · Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet:
www.hansgrohe.com
02/2023
9.08437.01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>