AFI C-5817X Murphy Bed With Charging Station Instruction Manual
- June 17, 2024
- AFI
Table of Contents
TWIN XL
MURPHY BED
WITH CHARGING STATION
C-5817X Murphy Bed With Charging Station
ASSEMBLY INSTRUCTIONS
Before assembling your murphy bed, please read through these instructions
carefully and familiarize yourself with the different parts.
ATTENTION! If you receive a damaged or defective item, please contact
afifurnishings at
[email protected]
or 1-800-955-3726
HARDWARE
NOTE: WE INCLUDE SPARE HARDWARE IN CASE DAMAGE OCCURS DURING ASSEMBLY.
PARTS LIST
STEP 1
Insert all wooden dowels (A) into the locator holes on
(03)(04)(05)(06)(07)(08) and (15).
Install USB charger (J) as shown below. Using black wood screw and cable
fastener tighten with phillips head screw driver. (Customer Supplied )
STEP 2
Attach left side panels (03) to the shelf (06), front rail (05), middle back
rail (07) and bottom back rail (08) as shown below. Use JCB (B)(D) and barrel
nut (E).
Tighten with Allen wrench (H)
STEP 3
Guide the back panel (09) in carefully so that it won’t jump out of its
grooves. Be sure it fits fully into its groove at the bottom (in the side
panel) before fitting the other side panel.
STEP 4
Attach right side panels (04) to cabinet assembly as shown below. Use JCB
(B)(D) and barrel nut (E).Tighten with Allen wrench (H)
Be sure it fits fully into its groove at the bottom (in the side panel) before
fitting the side panel.
STEP 5
Guide the back panel (09) in carefully so that it won’t jump out of its
grooves. Be sure it fits fully into its groove at the middle rail before
fitting the top panel.
STEP 6
Attach top panel (02) to cabinet assembly as shown below. Use JCB (B). Tighten
with Allen wrench (H)
STEP 7
Open top drawer folding leg until lock of metal support as shown below.
STEP 8
Attach door panel to cabinet assembly as shown below. Use wood screw (F)
tighten with Phillips head screwdriver. (customer supplied).
Be sure to align with cabinet.
STEP 9
Lift the door and push the metal support. Push the door closed and latch
both sides as shown below.
STEP 10
Attach triangle bracket (I) to the back of cabinet as shown below. Use wood
screw (F) tighten with Phillips head screwdriver. (customer supplied).
STEP 11
Lay the drawer face (11) on smooth, flat surface so the groove is facing
upwards.
Fit the drawer side (12) to drawer face (11), Use JCB (C), align groove inside
panel with groove in drawer face. Tighten with Allen wrench (H).
STEP 12
Guide the drawer panel (14) in carefully so that it won’t jump out of its
grooves. Be sure it fits fully into its groove at the bottom (in the drawer
face) before fitting the drawer back. Attach drawer panel support (15) to the
drawer face as shown below.
STEP 13
Attach drawer back (13) and drawer side block (16) to bed drawer assembly as
shown below. Use JCB (C)(D). Tighten with Allen wrench (H). Use wood screw (G)
tighten with Phillips head screwdriver.
(customer supplied)
STEP 14
Move the murphy bed where you want to place them in the room. Push drawer
assembly in as shown below. Be sure to align with cabinet.
STEP 15
Unlatch the door and open top drawer folding leg until lock of metal support,
folding down as shown.
STEP 16
Open and pull footboard frame and open footboard leg as shown below.
STEP 17
Install folding mattress (17) to the bed. Open top panel as shown below.
Congratulations!
Your Murphy bed is now ready for use.
We recommend that you recheck that all screws are tight,
and that all parts are secure before use to ensure lasting Safety.