hansgrohe 24220XXX Pulsify S Showerpipe 260 1jet with Shower Tablet Instructions

Hansgrohe 24220XXX Pulsify S Showerpipe 260 1jet with Shower Tablet

Product Information

Specifications

• Model: Showerpipe 260 1jet
• Product Codes: 24220XXX (standard), 24221XXX (EcoSmart)
• Maximum Pressure: 1 MPa
• Operating Pressure Range: 0.1 – 0.5 MPa
• Test Pressure: 1.6 MPa (1 MPa = 10 bar = 147 PSI)

Frequently Asked Questions

• Q: What should I do if the shower head drips constantly?
  • A: Refer to the assembly instructions for solutions to dripping issues.
• Q: How should I adjust the thermostat?
  • A: Please for instructions on adjusting the thermostat for your shower pipe.
• Q: What are the maintenance recommendations for this product?
  • A: Maintenance guidelines are detailed of the user manual. Regular maintenance is essential for optimal performance.

Safety Information

Safety Notes

• Gloves should be worn during installation to prevent crushing and cutting injuries.
• The product may only be used for bathing, hygienic and body cleaning purposes.
• The arm of the shower head is intended only to hold the shower head. Do not load it down with other objects!
• Children as well as adults with physical, mental and/or sensoric impairments must not use this product without proper supervision. Persons under the influence of alcohol or drugs are prohibited from using this product.
• Do not allow the streams of the shower touch sensitive body parts (such as your eyes). An adequate distance must be kept between the shower and you.
• The product may not be used as a holding handle. A separate handle must be installed.
• The hot and cold supplies must be of equal pressures.

Installation Instructions

• Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• The installation dimensions stated in these installation instructions are ideal for people of approximately 1800 mm in body height. The dimensions can be altered if required. In this case, pay attention to the fact that a change of installation height will also change the minimum height, and that the altered mounting dimensions must be taken into consideration.
• During installation of the product by qualified trained personnel, make sure that the entire fastening surface is even and smooth (no protruding seams or tile offset), that the finish of the wall is suitable to apply the product and has no weak points.
• The mesh washer must be insert to protect the shower against incoming dirt by pipework. Incoming dirt leads to defects or/and can damage parts of the shower; such caused faults voids all liability and guarantee claims.
• The product is not designed to be used with steam baths!
• If required, the bottom part of the pipe between the fixture and the shower head can be shortened with a fine-toothed saw.

Special information for UK

• If installing this product with a pump, please be aware that it has to have negative head switching.
• This product will not function with a positive head pump.

Technical Data

• Operating pressure: max. 1 MPa
• Recommended operating pressure: 0,1 – 0,5 MPa
• Test pressure: 1,6 MPa
  • (1 MPa = 10 bar = 147 PSI)
• Hot water temperature: max. 60°C
• Centre distance: 150±12 mm
• Connections G 1/2: cold right – hot left
• Thermal disinfection: 70°C / 4 min

Safety against backflow
The product is exclusively designed for drinking water!

Symbol Description

• Do not use silicone containing acetic acid!
• Safety Function

The desired maximum temperature for example max. 42°C can be pre-set thanks to the safety function.

• Adjustment

After the installation, the output temperature of the thermostat must be checked. A correction is necessary if the temperature measured at the output differs from the temperature set on the thermostat.

• Maintenance
  • The check valves must be checked regularly according to EN 806-5 in accordance with national or regional regulations (at least once a year).
  • To guarantee the smooth running of the thermostat, it is necessary from time to time to turn the thermostat from total hot to total cold.
• Dimensions
• Flow diagram
• Spare parts
• Special accessories (order as an extra)
• tile-matching-disk Colors #95239XXX
• Cleaning
• Operation

To empty the overhead shower after use, hold it in a slightly inclined position.

More Information

Dimensions

Flow diagram

Installation Instructions

Adjustment

Safety Function

Operation

Cleaning

• www.hansgrohe.com/cleaning-recommendation

Cleaning recommendation / Warranty / Contact

QUICK CLEAN

• Just clean: simply rub over the spray nozzles to remove lime scale.

Cleaning

Maintenance

Special accessories

• XXX = Colors
  • 000 = Chrome
  • 140 = Brushed Bronze
  • 670 = Matt Black
  • 700 = Matt White

Contacts

Hansgrohe

• Auestraße 5 – 9 · D-77761 Schiltach
• Telefon: +49 (0) 78 36/51-1282
• Telefax: +49 (0) 7836/511440
• E-Mail: info@hansgrohe.com
• Internet: www.hansgrohe.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>