Infinix ZERO 30 X6731B Smartphone User Manual
- June 17, 2024
- Infinix
Table of Contents
**Infinix ZERO 30 X6731B Smartphone User Manual
**
Explosion diagram specification
| 1 | OLED | 2 | VC |
|---|---|---|---|
| 3 | LCM FILM | 4 | MID FRAME |
| 5 | CCD | 6 | F CAM |
| 7 | SCREW M1.4L3.5D2.5*H0.5 | 8 | SCREW M1.2L2.0D2.3*H0.5 |
| 9 | UP SPEAK | 10 | MAIN CAM COPPER |
| 11 | 2M CAM ADH | 12 | 2M KH7 RUBBER |
| 13 | PS RUBBER | 14 | MAIN PCB |
| 15 | MAIN R CAM | 16 | RF LINE2 |
| 17 | UP FRAME | 18 | FLASH FPC |
| 19 | RF LINE1 | 20 | DECO PLATIC SUPI |
| 21 | NFC | 22 | BAT COVER |
| 23 | DECO AL | 24 | DECO GLASS |
| 25 | FLASH SHIELD | 26 | DECO FLASH SHIELD AL |
| 27 | DECO FLASH SHIELD AL ADH | 28 | FLASH SHIELD ADH |
| 29 | BOX | 30 | DOWN FRAME |
| 31 | ANT PCB | 32 | FINGGER PRINT |
| 33 | 2M CAM WJ | 34 | SUB VIB |
| 35 | 2M CAM XH | 36 | SUB PCB |
| 37 | VOL SIDEKEY | 38 | POWER SIDKEY |
| 39 | USB RUBBER | 40 | SIDKEY STEEL |
| 41 | OLED FPC RUBBER | 42 | CARD HOLDER |
| 43 | SIDKEY FPC | 44 | SIDKEY FRAME |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key
- NFC
SIM card installation
- Power off mobile.
- Refer to the following picture for SIM card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
Use only INFINIX charger and cables. Other chargers or cables may damage the
device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the condition that this device does not cause harmful interference.
Information to user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is
1.6W/kg averaged over one gram of tissue. Device types:
X6731B (FCC ID: 2AIZN-X6731B)has also been tested against this SAR limit. The
highest SAR value reported under this standard during product certification
for use when properly worn on the body is 0.750 W/kg and for head is 0.788
W/kg. Simultaneous RF exposure is 1.124W/Kg. This device was tested for
typical body-worn operations with the back of the handset kept 10mm from the
body. To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 10mm separation distance between the user’s body
and the back of the handset. The use of belt clips, holsters and similar
accessories should not contain metallic components in its assembly. The use of
accessories that does not satisfy these requirements may not comply with FCC
RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System: AndroidTM
Android is a trademark of Google LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>