QSFPTEK S5300-24T4S 24 Port Gigabit Ethernet L2+ Switch User Guide

QSFPTEK S5300-24T4S 24 Port Gigabit Ethernet L2+ Switch User Guide

24-Port Gigabit Ethernet L2+ Switch
24x 10/100/1000BASE-T RJ45 Ports, with 4x 1GSFPUplinks,Fanless

Introduction

The S5300-24T4S is a managed L2+ access switch with 24x 10/100/1000BASE-T RJ45 ports and 4x 100/1000M SFP uplink ports, supporting OSPF. With a finless design, this layer 2+ switch ensures silent operation and delivers a low-power and noiseless solution for power-saving and noise-sensitive environment deployment. Effortlessly control and manage the switch through both CLI and WEB interfaces. The S5300-24T4S 24-port switch is an excellent choice for SMBS and noise-sensitive spaces, such as working offices, homes, libraries, schools, etc.

We appreciate your decision to select S5300-24T4S. This manual is intended to help you become acquainted with the switch design and provide instructions for implementing the switches into your network.

Accessories

• Power Cord x1

• Console Cable x1

• Mounting Bracket x2

• M3 Screw x6

• Rubber Pad x4
  

Hardware Overview

Front Panel Ports

Front Panel LEDs

system will return to the default setting.
SYS LED| /| If the switch is started, the system indicator flickers.
PWR LED| /| If the switch is powered on, the indicator is on.

Back Panel

Installation Requirements

Tools Preparation

• Screwdriver
• Static-proof wristband
• Bolt
• Ethernet cable
• Other Ethernet terminal devices
• Control terminal

Safety Principles

Keep dustless and clean during or after the installation.

• Put the cover in a safe place.
• Put tools in the right place where they are not easily falling down.
• Put on relatively tight clothes, fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
• Put on protective glasses if the environment may cause damage to your eyes.
• Avoid incorrect operations that may cause damage to humans or devices.

Site Environment

• Make sure that the workshop is well-ventilated, the heat of electrical devices is well- discharged
• Avoid damaging devices by following the electrostatic discharge prevention procedure.
• S5300-24T4S Hardware Installation Manual
• Put the machine box in a place where cool air can blow off the heat inside the machine box.
• Make sure the machine box is sealed

Mounting the Switch

Connecting the Power

• Plug the AC power cord to the switch power port on the back rear.
• Connect the other end of the power cord to an AC power source equipment.

Connecting the RJ45 Ports

• Connect one end of the Ethernet cable to the RJ45 port on networking equipment, succahs PC, printer, server, storage, etc.
• Connect the other end of the Ethernet cable to the switch RJ45 port.

Connecting the SFP Port

• Insert the SFP module into the SFP port.
• Plug a fiber patch cable into the SFP transceiver.
• Connect the other end of the fiber to the device that you want to realize data communication.

Connecting the Management Ports

Connecting the Console Port

• Prepare a console cable.
• Insert the RJ45 connector of the console cable into the console port on the switch.
• Connect the DB9 female connector on the other end of the console cable to the serial port on the computer host.

Configuring the Switch

Configuring the Switch Using the Web-based Interface

Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.

Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any number from 2 to 254) and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.

Configuring the Switch Using the Console Port

Step 1: Use the console cable to directly connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.

Step 4: Enter the default username and password (admin/admin).

Troubleshooting

Hardware Fault Analysis

1. Power and cooling systems-power and fan
2. Port, cable and connection-ports on the front panel of the switch and the cables connecting these ports

Faults Relative to Power and Cooling System

Do the following checkups to help remove the fault:

1. When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
2. If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 “Requirements for Common Locations”.
3. If the switch cannot be started and the PWR indicator is off, check the power.

Faults Relative to Port, Cable and Connection

Do the following checkups to help remove the fault:

1. If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
2. If the power on-off is at the “ON” location, check the power source and the power cable.
3. If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.

Support and Other Resources

• Contact us: https://www.qsfptek.com/company/contact-us.html
• Customer Success: https://www.qsfptek.com/resources/customer-success-stories
• Email: support@qsfptek.com

Product Warranty

S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. You are eligible to apply for a return within 14 days and exchange within 90 days of receiving them.

For more details about applying qualifications, please live chat or email sales@qsfptek.com for support.

5 Year Warranty
14-day Return Window

Documents / Resources

| QSFPTEK S5300-24T4S 24 Port Gigabit Ethernet L2+ Switch [pdf] User Guide
S5300-24T4S 24 Port Gigabit Ethernet L2 Switch, S5300-24T4S, 24 Port Gigabit Ethernet L2 Switch, Gigabit Ethernet L2 Switch, Ethernet L2 Switch, L2 Switch, Switch
---|---

References

• QSFPTEK - Compatible Optical Transceivers Factory Outlet
• Customer Success Stories - QSFPTEK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>