OLIGHT i3t-zirconium 180lm AAA Flashlight User Manual
- June 17, 2024
- OLIGHT
Table of Contents
USER MANUAL
i3T EOS Zirconium
(LIMITED EDITION)
Thank you for purchasing this Olight product. Please read this manual carefully before use and keep it forfuture reference!
IN THE BOX
SPECIFICATIONS
HIGH| 180 lumens| 60m| 4I0min
LOW| 5 lumens| 12m| 16h
900cd| l.5m| IPXB| 60m
LENGTH| | B9mm/3.5in|
BEZEL DIAM| | 15mm / 0.59in|
WEIGHT| | 64g/2.26oz
(Including battery)|
*All above specifications are test results based on ANSI/NEMA FL1-2009 Standards.
INSULATING FILM
Before first use, unscrew the tailcap and remove the insulating film.
BATTERY INSTALLATION
If the battery needs to be replaced, make sure that the positive end of the new battery faces the flashlight head when you put ii in.
AVAILABLE BATTERIES
- 1 x 1.5V AAA alkaline battery (included)
- 1 x AAA lithium battery (compatible)
- 1 x AAA NiMH battery (compatible)
DANGER
- DO NOT shine the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
- DO NOT cover the light head when the flashlight is on, or place the flashlight head on the ground. The radiation energy of the flashlight may cause damage to the flashlight itself, or even result in burning to other materials.
- DO NOT use batteries other than the ones mentioned in the “available batteries”, especially rechargeable lithium batteries, otherwise it could lead to the damage of the flashlight, or unexpected danger.
WARNING
- Keep out of reach of children.
- If the light is about to be put aside for a long time or be transported, please unscrew the tailcap and remove the battery to cut off the circuit.
NOTICE
- Ensure battery is inserted with the positive (+) end pointing to the head of the flashlight (LED side).
- When the flashlight is turned on, it will go to low as the default mode. Continue to click on and off within 2 seconds after it was turned off to shift between low and high brightness levels. If it is turned on over 2 seconds after it was switched off, it will go directly to low mode as default again.
- It is normal for the flashlight not being able to reach 180 lumens when the battery voltage is too low (under 1.0V).
- It is normal for the flashlight to blink when the battery is running out.
EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the
usage of the product inconsistent with the warnings in the manual, including
but not limited to using the product inconsistent with the recommended lockout
mode.
When the light is first turned on, it will go to low as the default mode. Soft press without fully clicking for momentary on. Cycle through momentary low and high mode by quickly soft pressing, letting go, and soft pressing again. Deep press for constant on (you will hear a click). Continue to click on and off within 2 seconds after it was turned off to shift between low and high brightness levels. If ii is turned on over 2 seconds after ii was switched off, ii will go directly to low mode as default again.
WARRANTY
seller for repair or replacement.
Within 30 days of purchase: Contact the original Within 5 years of purchase:
Contact 0light for repair or replacement.
This warranty does not cover normal wear and tear, modifications, misuse,
disintegrations, repair by anyone other than an authorized retailer
negligence, accidents, improper maintenance, or or Olight itself.
USA Customer Support
cs@olightstore.com
Global Customer Support
contact@olightworld.com
Visit www.olightworld.com to see our complete
product line of portable illumination tools.
Dongguan 0light E-Commerce Technology Co., Ltd.
4th Floor, Building 4, Kegu Industrial Park, No 6
Zhongnan Road, Changan Town, Dongguan City,
Guangdong, China.
Made in China 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>