OLIGHT Odin S 2000 Lumens Picatinny Rail Mounted Rechargeable Tactical Flashlight User Manual

Odin S 2000 Lumens Picatinny Rail Mounted
Rechargeable Tactical Flashlight
User Manual Odin S
Powerful rail-mounted light with remote switch.

IN THE BOX

Table 1:
Specifications (18650 Battery)

• Above data are tested per ANSI/PLATO FL 1-2019 standard in Olight’s labs for reference.
  CR123A Battery (Optional Accessory)

• Above data are tested per ANSI/PLATO FL 1-2019 standard in Olight’s labs for reference.
  Table 2:
  USB Magnetic charging cable

Figure 1
Remove the insulating film before use

Figure 2
Charging Figure 3
Use the battery holder

Install two CR123A batteries into the battery holder.
Note: Ensure that the batteries are installed with the correct polarity.
Figure 4
Rail mount installation

Loosen the screws and install the rail mount in its desired position, then tighten the screws.
Figure 5
Rail mounted light installation

Loosen the knob locking lever on the rail mount (counter clockwise) until it stops. Adjust the width of the rail mount opening by pushing the knob locking lever (Note: Do not put your fingers against the movable rail mount on the opposite side of the knob locking lever). Place the T-mount on the product into the T-shape inside the rail mount. (The two screws on the rail mount align with the slots on the product’s T-mount).

Lastly, lock the knob locking lever on the rail mount with tools to make it ready for use (turning it clockwise).

Figure 6
Light removal

CONSTANT ON

MOMENTARY ON

|
---|---

REMOTE SWITCH OPERATING INSTRUCTIONS AS BELOW

|
---|---

How to operate:

1. Product specifications, see Table 1 and Table 2.

2. Remove the insulating film before use, see Figure 1.

3. Charging, see Figure 2.

4. Use the battery holder, see Figure 3.

5. Product installation as below:
   5.1 Rail mount installation, see Figure 4.
   Loosen the screws, install the rail mount in the desired position, and then tighten the screws.
   5.2 Rail mounted light installation, see Figure 5.
   Unscrew the knob locking lever on the rail mount counterclockwise until it stops. Push the knob locking lever to adjust the width of the rail mount opening. Place the T-mount on the product into the T-shape inside the rail mount, ensuring that the two screws on the rail holder align with the slots in the product’s T-mount. Lastly, lock the knob locking lever on the rail mount by turning it clockwise using a tool.
   5.3 Light removal, see Figure 6.
   To remove the product, loosen the knob locking lever on the rail mount and push it to adjust the width of the rail mount opening.

6. Tail switch operating instructions as below:
   6.1 Constant On.
   6.1.1 Low, see Figure 7.
   Press slightly and quickly for Low, and press again to turn it off.
   6.1.2 High, see Figure 8.
   Press hard and quickly for High, and press again to turn it off.
   6.2 Momentary On:
   6.2.1 Low, see Figure 9.
   Press slightly and hold for Low, and release to turn it off.
   6.2.2 High, see Figure 10.
   Press hard and hold for High, and release to turn it off.
   6.3 Switch to High, see Figure 11.
   In Low, single press or heavily press and hold the switch for High.
   6.4 Enable/disable the Strobe function, see Figure 12.
   When the light is off, press the button hard five times (or more) quickly, and hold it for more than 1 second at the last press, then the Strobe can be enabled or disabled.
   6.5 Strobe (when Strobe function is activated), see Figure 13.
   Double (or more) press the button hard quickly to turn on the Strobe, and press once again to turn it off.

7. Remote switch installation, see Figure 14.
   To install the remote switch, first, push the detent ring towards the tail of the light, and then screw the ring clockwise. To remove the remote switch, simply screw the detent ring counterclockwise until you hear a click.

8. Remote switch operating instructions as below:
   8.1 Constant On, see Figure 15.
   Press the LO/HI button quickly for Low mode /High mode, and press again to turn it off.
   8.2 Momentary On, see Figure 16.
   Press and hold the LO/HI button for Low mode /High mode, and release it to turn the light off.
   8.3 Enable/disable the Strobe function, see Figure 17.
   When the light is off, press the HI button five times (or more) quickly, and hold it for more than 1 second at the last press, then the Strobe can be enabled or disabled.
   8.4 Strobe (when Strobe function is activated), see Figure 18.
   Double (or more) press the HI button quickly to turn on the Strobe, and press once again to turn it off.

WARNING

• Do not look directly at the light source or shine to eyes, because it may cause temporary blindness or permanent damage to the eyes.
• Do not block the light at close range, the energy emitted from the light may cause the object to burn.
• Do not charge the light with any other non-specified chargers.

CAUTION

• CAUTION HOT: Do not touch the hot surface place, it may cause skin burns.
• Do not put a hot light into any type of fabric bag or fusible plastic container.
• Do not store, charge or use the flashlight in a car or similar places where the temperature may exceed 60°C.
• Do not short-circuit the charging port with the metallic objects.
• Do not disassemble the product.

NOTICE

• Please keep the charging port clean and dry.
• When the battery voltage is low, its maximum output is 300 lumens.
• Battery holder is needed in using two CR123A batteries.
• When using two non-rechargeable CR123A batteries , do not use IMCC to charge the product.
• For non-rechargeable battery, it is recommended to use Panasonic, Sanyo, Energizer CR123A or Duracell 123 batteries.
• This product is not compatible with Olight CR123A batteries.
• It is recommended to use Olight’s ORB1-186S35 rechargeable battery. If you use other 18650 batteries, the battery discharge capacity must meet 10A and above to output 1500 lumens.

EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode.
WARRANTY
We are proud to offer a lifetime warranty in Australia, China, France, Germany, and the USA. We are also working hard to expand coverage to more countries, where we provide a 2 or 5-year warranty. The warranty covers defects in material and workmanship  under normal use, excluding loss, theft, deliberate damage, or cosmetic damage. For complete warranty information, please visit olightworld.com or your local Olight official website.
Australia Customer Support
contact@olightstore.com.au
Austria Customer Support
kontakt@olightstore.at
Canada Customer Support
cs@olightstore.ca
China Customer Support
WeChat: Olight’s
France Customer Support
cs@olightstore.fr
Germany Customer Support
kontakt@olightstore.de
Italy Customer Support
contatto@olightstore.it
Japan Customer Support
cs@olightstore.jp
Korea Customer Support
olightkorea@olightworld.com
Spain Customer Support
contacto@olightstore.es
Thailand Customer Support
cs@olightstore.co.th
UK Customer Support
contact@olightstore.uk
USA Customer Support
cs@olightstore.com
For other countries and regions, please contact Global Customer Support
contact@olightworld.com

Dongguan Olight E-Commerce Technology Co., Ltd.
4th Floor, Building 4, Kegu Industrial Park,
No 6 Zhongnan Road, Changan Town, Dongguan
City, Guangdong, China.
Made in China 3.4000.0758
B. 11, 22, 2023

Documents / Resources

| OLIGHT Odin S 2000 Lumens Picatinny Rail Mounted Rechargeable Tactical Flashlight [pdf] User Manual
Odin S 2000 Lumens Picatinny Rail Mounted Rechargeable Tactical Flashlight, Odin S, 2000 Lumens Picatinny Rail Mounted Rechargeable Tactical Flashlight, Rail Mounted Rechargeable Tactical Flashlight, Rechargeable Tactical Flashlight, Tactical Flashlight, Flashlight
---|---

References

• Olight | Illuminate Your World.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>