greenworks WLG906 24V 2 In Lumen Standing Light LED Work Light Instruction Manual

greenworks WLG906 24V 2 In Lumen Standing Light LED Work Light

DESCRIPTION PURPOSE
The standing light provides a safe, portable, and powerful source of light when needed.

OVERVIEW

1. ON/OFF Switch
2. 10 W Spotlight
3. 12 × 0.5 W LED Ring
4. Extendable LED Tube
5.  Tube Compression
6. Ring Clamp Leg Clamps
7. Battery Housing
8. Storage Strap

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power too/ will increase the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A lapse of attention while operating power tools may result in serious personal injury.
• Use personal protection. Always wear eye protection. Protective products such as dust mask, non-skid safety shoes, hard hat or hearing protection used appropriately will reduce personal injuries.
• Do not over-reach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or fire.
• • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions.

Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

SPECIFIC SAFETY RULES

• Know your power tool. Read operator manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this power tool. Obey this instruction will reduce shock, fire or serious injury.
• Battery tools do not have to be plugged into an electrical outlet; thus, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Obey this instruction will reduce the risk of electric shock, fire, or serious injury,
• Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possible injury.
• • Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.
• Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.
• Do not charge battery tool in a damp or wet location. Obey this instruction will reduce the risk of electric shock.
• For best results, your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F. To reduce the risk of serious injury, do not store outside or in vehicles.
• Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your sink, wash immediately with soap and water. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Obey this instruction will reduce the risk of serious injury.
• Keep these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you borrow someone this tool, loan them these instructions also to prevent incorrect use of the machine and possible injury.
• When using flashlights or lanterns, additional precautions should always be followed, including the following:
  • To reduce the risk of injury, close supervision is necessary when a product is used near children.
  • Do not contact hot parts.
  • Only use attachments recommended or sold by the manufacturer.
  • Do not use in the rain.
  • To reduce the risk of electrical shock, do not put in water or other liquid. Do not place or store product where it can fall or be pulled into a tub or sink. Replace with specific part of product in question.
  • To reduce the risk of injury, do not stare at operating lamp. Serious eye injury could occur.

 SYMBOLS ON THE PRODUCT

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

RISK LEVELS
The following signal words and meanings are intended to explain the levels of risk associated with this product.

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The toxic and corrosive materials below are in the batteries used in this machine: Lithium-ion, a toxic material.
WARNING
Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding damaged or worn out Li-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for lithium-ion disposal.

WARNING
If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:

• Cover the terminals of the battery with heavy-duty adhesive tape.
• DO NOT try to remove or destroy any of the battery pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on skin, and do not swallow it.
• DO NOT put these batteries in your regular household trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.

PROPOSITION 65
WARNING This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well- ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Save these instructions.

INSTALLATION

UNPACK THE MACHINE A WARNING Make sure that you correctly assemble the machine before use.

WARNING

• If parts of the machine are damaged, do not use the machine.
• If parts are missing, do not operate the machine.
• If parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.
   WARNING For your personal safety, do not insert battery before the tool is assembled completely.

ADJUST THE TRIPOD

1. Disconnect strap from tripod legs.
2. Pull legs away from base until leg supports are fully extended.
3. Extend tripod legs individually by releasing clamps and adjusting to desired length. Once desired length is achieved, position clamps to the lock position.

ADJUST THE TUBE LIGHT

1. To extend the area light: Rotate the ring lock of extendable area light.
2. When the unlock icon is aligned with the right arrow, the light is in unlocked state.
3. Pull the light head upwards until fully extended.
4. With the tube extended, rotate the lock ring to the lock position.

ADJUST THE LIGHT HEAD

1. The light head can be adjusted up and down to 90° and can rotate 260° .

INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.
• Read and understand the instructions in the battery and charger manual.

1. Align the ribs on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

REMOVE THE BATTERY PACK
Push and hold the battery release button (7). Remove the battery pack from the machine.

OPERATION

• IMPORTANT
  Before you operate the machine, read and understand the safety regulations and the operation instructions.

• WARNING
  Be careful when you operate the machine.

POWERING ON THE LIGHT

1. Install the battery pack.
2. Press the ON/OFF switch (1) to turn the light on.
3. Continue to press the ON/OFF switch to cycle through light settings and power off the device.

NOTE
Switching Order:

1. LED Tube
2. 10 W Spotlight
3. 12 x 0.5 W LED Ring
4. All On
5. Off

POWERING OFF THE LIGHT

1. Cycle the ON/OFF switch to turn the light off.

MAINTENANCE

• CAUTION Do not let brake fluids, gasoline, petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.
• CAUTION Do not use strong solvents or detergents on the plastic housing or components.
• WARNING Remove the battery pack from the machine before maintenance.

STORAGE AND MAINTENANCE

• CAUTION Clean the cooled lens with household window cleaner; then wipe with a clean soft, dry cloth. Clean the housing with a clean, dry cloth. Do not expose the light to direct sunlight. Dry thoroughly before use. Store the light in a dry, clean area. Avoid high humidity.
• CAUTION Only qualified service personnel must perform repairs. Do not open the exterior casing of the light as there are no-user-serviceable parts inside. Opening or tampering with the casing may void warranty and/or cause damage to the product or personal injury. LED bulbs will never wear out under normal conditions and do not need to be replaced.

WARNING
Store the light in a clean and dry area. To prevent fire or burning, allow the light to cool down completely before you store it.

LUMENS
TIP

The light features 4 different functions. The brightness of tube light reaches 1500 lumen, the brightness of 10 W spotlight reaches 500 lumen, the brightness of 12 x 0.5 W LED ring light reaches 300 lumen.

TECHNICAL DATA

The recommended ambient temperature range:

LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. Greenworks, at its own discretion, will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been purchased or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners’ manual supplied with the product when new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear;
4.  Routine maintenance items such as lubricants, blade sharpening; Normal deterioration of the exterior finish due to use or exposure.

HELPLINE: Warranty service is available by calling our toll-free helpline at 1-888-909-6757.

TRANSPORTATION CHARGES : Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.

• USA address:
  • Greenworks Tools P.O. Box 1238, Mooresville, NC 28115
• Canadian address: Greenworks Tools Canada, Inc. P.O. Box 93095, Newmarket, Ontario, L3Y 8K3
• Mexico address: TECNOLOGIA CAMPO Y JARDIN S.A. DE C.V. ADMINISTRADORES No. 5336 A, COL. ARCOS DE GUADALUPE, ZAPOPAN, JALISCO , C.P. 45037

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>