Kaadas KA214 Smart Lock Instructions

Kaadas KA214 Smart Lock

Information and Safety Warnings

• Failure to follow these instructions could result in damage to the product and void the factory warranty.
• The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and lessening of security.
• This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners, or polishes could damage the coating and result in tarnishing.

NOTE: Do not load batteries until the lock is completely installed.

1. Master PIN Code (4~10 digits): The default master PIN code is “12345678”, It’s required that you change it to a code of your own before programming.
2. User PIN Code (4~10 digits): A total of 250 user codes may be programmed.
3. Neither master nor user PIN codes support the following combination of numbers.

Parts Illustrations

Interior Assembly

Exterior Assembly

CAUTION: Master and User PIN codes have 4~10 digits, the default master PIN code is{12345678). Please change it before programming the lock.

Definitions

Master Code
Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. (Property owner/ manager should keep this information confidential.)
Enter Master Mode

1. Touch the Keypad screen with your hand to activate the lock.
2. Press [*] twice, input the master PIN code, and press (#] to confirm.

Auto Unlock
Automatically locks the deadbolt 30 seconds after unlocking. This feature is enabled by default.
Wrong Entry Limit
After 10 unsuccessful attempts at entering a valid PIN code, the unit will shut down for 3 minutes.
Silent Mode
The beep sounds when pressing the keypad can be muted. But you will still hear low battery and system alerts.
Vacation Mode
This is a security feature for you when you are leaving your home for a vacation or a long trip. Enabling vacation mode will restrict all user codes until the master code is entered on a keypad. If the lock is unlocked by thumb turn or the key, the lock will sound an alarm.
Privacy Mode
When the privacy mode is activated, the door cannot be opened from outside.

Factory Default Settings

Restore factory default settings

1. Keep your lock in “unlock” status, and insert 4AA batteries in the battery pack.
2. Use the provided reset pin to press and hold the reset button for more than 5 seconds until hearing a beep sound.
3. If reset is successful, the bolt will extend on its own to learn the orientation of the door.

Lock handing
If the installation is complete, the knob cannot be turned manually, you can restore factory settings once.

Troubleshooting

• The lock can’t be locked or unlocked by a keypad.
• Make sure the codes are not disabled. If needed, restore the lock to default settings.
• The keypad doesn’t respond when touched (no lights and no beeps).
• Make sure the power cable is properly connected. Change the batteries with 4 brand-new AA standard alkaline batteries. Do not mix old and new batteries.
• The Kaadas logo on top of the keypad keeps flashing red?
• It indicates the battery life is under 20% and please change the batteries as soon as possible.
• Forgot the Master or user PIN codes
• Perform a reset to erase all passcodes. Once the reset is complete, all passcodes will be erased, and the master code will return to the default. (12345678).

How to use

Unlock the door from outside

Lock the door from outside

• One-touch Locking
• Press any key on
• keypad for 2 sec

Enable Auto-lock
When this feature is enabled, the lock will automatically relock itself 30 sec after being unlocked.

Unlock the door from inside

• Rotate the thumb-turn to the horizontal position.

Lock the door from inside

Z-Wave™ Module pairing instructions

Optional network module required
Z-Wave™ pairing setting can only be programmed through the Master Mode Menu at the Lock.

1. Follow the user guide of your Smart Hub or Network gateway to enter Learning or Pairing Mode.
2. Touch the Keypad screen with your hand to activate the lock.
3. Enter master mode.
4. Enter “O” to enter the Network Setting.
5. Enter “1” to join the network or “2” to exit a network.
6. Follow the steps on your 3rd party interface or network controller to sync Z-Wave™.

CAUTION
An optional Z-Wave™ or other Network Module is required to enable this feature. If the lock is connected to a network controller, it is recommended that all programming of PIN Codes and settings is completed through 3rd party user interface to ensure stable communication between the lock and controller is maintained.

Lock Operation

• The default master code is 12345678. It’s required that you change it to a code of your own before programming.
• When the setting is unsuccessful, the indicator light will flash red.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

ISED Statement
English: This device contains licence-exempt transmitters)/receivers) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

• The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
• This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
• This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>