Ella s Bubbles Standard Acrylic Walk In Bathtub Owner’s Manual

Ella’s Bubbles Standard Acrylic Walk In Bathtub

Specifications:

• Model: Acrylic Walk-in Bathtub
• Manufacturer: Ella’s Bubbles
• Contact: 800.480.6850 | info@ellasbubbles.com
• Website : www.ellasbubbles.com

Unpacking and Inspecting:

Upon receiving your walk-in bathtub, follow these steps:

1. Inspect the crate and carton for damages. Take pictures and record details if damages are found.
2. Remove the front apron and end panel before carrying into the house to avoid damaging the tub.
3. Do not lift the bathtub by plumbing or other parts.
4. Inspect for any loosened parts during transit.

Moving Your Ella Walk-in Bath:

When moving the tub, follow these guidelines:

• Avoid contact between the front panel and floor/stairs to prevent damage.
• Remove all access panels before carrying the tub to prevent breakage.
• Lift and carry the tub only by the frame to protect the bottom and air jets.

Warnings and Labels:

Important warnings to note:

• Read and comply with all instructions to avoid product damage or injury.
• Returns are accepted only in the original packaging used for shipping.
• Ensure air pipe connection to push controls is properly tightened before finalizing installation.

FAQ:

• Q : What should I do if I find damages upon receiving the bathtub?
• A : Take pictures, record details, notify the delivery driver, and contact the company for further instructions on claim processing.
• Q: Can I carry the tub by the panels?
• A : No, it is recommended to lift and carry the tub only by the frame to prevent damage.

Unpacking and Inspecting

• Upon receiving your walk-in bathtub please inspect the crate and carton for any damages. If damages are found please take a few pictures of the damages with your phone record the details on the shipper delivery document and ask the driver to sign it. If you think the product may be damaged note that on the delivery document and call 800- Damages must be recorded on shippers delivery documents for proper claim processing.
• After inspecting the crate and accepting the product please unpack the crate as shown in images. When the product is unpacked please remove the front apron with access panels and end panel before carrying it into the house. By removing the apron and access panels you will be able to grab onto the frame to carry the tub inside. Do not lift the bathtub by the plumbing or other parts. Avoid hitting the sides or the bottom so as not to break off the air jets or other parts of the bathtub. Inspect the plumbing or other parts that may have loosened in transit or by carrying the tub inside your home.

WARNING

REMOVE END PANELS BEFORE ATTEMPTING TO MOVE OR CARRY. FAILURE TO DO SO CAN LEAD TO DAMAGING AIR JETS AND OTHER COMPONETS OF THE BATHTUB.

Moving your Ella Walk in Bath

Toe Kick Access (3)

• Access to parts
• Option to lower the Threshold

WARNING: Do not carry the walk-in tub by the panels. Be careful when carrying the tub, and avoid front panel contact with the floor or stairs to prevent damage. Make sure no loose parts are hanging down. Remove all four (4) access panels before carrying the tub to prevent them from falling out and breaking.

WARNING: Lift and carry the tub only by the frame. Protect the bottom of the tub to avoid breaking the air jets positioned on the bottom of the tub.

Warnings and Labels

You must follow all the instructions in this manual.
FAILURE TO READ AND COMPLY WITH ALL INSTRUCTIONS CAN RESULT IN PRODUCT DAMAGE OR INJURY TO BOTH THE INSTALLER AND THE HOMEOWNER. IT WILL ALSO RESULT IN ASSUMPTION OF ALL LIABILITY BY SAID INSTALLER
NOTE : Returns are only accepted in the original packaging used for shipping. Use caution so as not to damage the cardboard crate or its wooden pallet. Do not dispose of shipping material until installation is complete. Please visit our website, www.ellasbubbles.com for complete details of the return/exchange policy.

WARNING

MAKE SURE AIR PIPE CONNECTION TO PUSH CONTROLS ARE PROPERLY TIGHTENED AND THAT PUSH CONTROLS ARE FUNCTIONING PROPERLY BEFORE FINALIZING THE INSTALLATION OF THE TUB.

Drain must open completely to drain properly and close completely to avoid unnecessary drainage. Ella Economy comes equipped with one (1) 2″ gravity- driven drain with (1) overflow and opener, and one (1) emergency pull-up up chain.

WARNING!

PLEASE READ BEFORE BEGINNING INSTALLATION
WARNING: Do not attach the handheld shower to the wall unless you have an extension hose with barrel protection. This may cause water to leak behind your walk-in tub.
TO INSTALL BARREL EXTENSION HOSE:

Water from the hose can drip down into the hand shower base and get behind your tub without the barrel protection.

1. Start by unscrewing your shower head mixer from the hose.
2. Next, take your stainless steel barrel and screw it on the end of the hose.
3. Take your extension hose and screw the end to the opposite side of the barrel.
4. Place the barrel in the shower base to plug the hole.
5. Finally, screw on the shower head mixer to the other end of the extension hose.

Important Safety Instructions

WARNING: Read through the entire manual completely before beginning installation.

CAUTION:
When using this product, basic precautions should always be followed. Read and follow all instructions pertaining to the risk of fire, electric shock and injury. Make sure and have your licensed electrician test all connections to the dedicated line, including the GFCI. Risk of electric shock; Do not permit electric appliances within 3 feet (1.5m) of the tub. i.e.: hair dryers, lamps, phones, radios, televisions, etc. To reduce the risk of injury, do not permit children or persons with disabilities to use this product unless they are supervised by an able-bodied adult at all times. Never drop or insert any objects into any openings. Do not turn on the Hydro jets without water reaching the waterline. The waterline is the point where all jets are covered with water.

DANGER:
Temperature in excess of 100.4 Fahrenheit (38 Celsius) may be harmful to your health. Check and adjust the temperature before use. Consult your physician before using your Ella Walk-in Bath if you have a heart condition or other health issues. People using medications, herbal remedies, sleep aids, and/or having adverse medical history should consult a physician before using this product. Pregnant women should NOT use this product before consulting their physician. Avoid the use of alcohol, drugs or other medications while using your walk in bath. Be aware, that hyperthermia is a risk when raising body temperature. Do no keep your body submerged in the heated bath for extended periods of time. The symptoms of hyperthermia include an increase in body temperature which can cause dizziness, lethargy, drowsiness and fainting. Avoid using the heated bath after strenuous activity.
Exercise caution while entering and exiting your Ella Walk-in Bath.

WARNING: USE TUB ONLY AS INTENDED! FAILURE TO DO SO CAN LEAD TO INJURY OR DEATH

WARNING

THE BATHER SHOULD ONLY SIT AS SHOWN IN THE FIGURE TO THE LEFT. SIT FULLY IN SEAT WITH BACK ON THE BACKREST. DO NOT ATTEMPT TO SLOUCH OR LIE DOWN IN THE FOOTWELL AREA! DO NOT ATTEMPT TO PUT YOUR FEET UP ON OPPOSITE SIDE OF THE TUB! In the case of bathers who do not have all functioning limbs or are paralyzed, bather must be attended by caregiver at all times and use an installed safety belt at all times.

CORRECT

WRONG POSITIONING

Installation

Required Steps Prior to Installation

Protecting the Bath
Cover and protect the bath shell and fixtures from scratches or other damages during the installation and tests. Remove the access panels when moving the Walk in Bath and always lift the bathtub from the frame.
Electrical
The unit MUST be connected to a circuit protected by a ground fault circuit interrupter (GFCI) provided and installed by a licensed electrician and tested periodically (refer to instructions provided by GFCI manufacturer). Operating the pumps without first filling the bath above the jets can cause permanent damage to your equipment. Push the GFCI “test” button into “reset” mode. If the GFCI fails to operate in this manner, there is a ground current flow or a device malfunction, indicating the possibility of electrical shock. If this occurs, turn OFF the power and do not use the bathtub until the source of the problem has been identified and corrected.
Water Test
It is important to test that the Hydro and Air Pumps are functioning properly before the final in-wall installation to avoid unnecessary repairs or removal.

• Place the tub on a completely flat surface in an area where it may be drained after testing.
• Using a clean rag and warm water wipe down the seal to ensure it is free of debris.
• Seal the drains (this can be done with tape) and fill the tub to at least three inches above the highest jet, or to the bottom of the grab bar if no jets are present.
• Allow the water to stand in the tub for 30 minutes and then inspect all plumbing and seals for leaks.
• Using appropriately rated three-prong extension cords, all plugged into separate outlets, operate all electrical components (air blower, water pump, and heater if applicable) for another 30 minutes and inspect for leaks again. Inspect the unions around the pump and heater.
• If a leak persists at a union after tightening, it may have been over-tightened or might have a displaced O-ring. Disassemble it and make sure the O-ring is seated properly. Do the same if a leak persists at the heater. Verify that the heater threads match the pipe threads.

Ella 2″ T-Type Single Port Floor Drain (One Drain Included)

Above the Floor Drain Installation

For best performance and faster drainage time, the 2″ drain can be connected to both 2″ ports. One (1) included cap can be used to cap off 1 unused port if 1 port is selected to be connected to the house drain. The direction is optional and shown in the image below. For best performance, it is suggested to use a Y vs T fitting to join both 2″ outlets and tap into the house drain. The fewer turns in the drainage system the less resistance and faster drainage.

Warning : make sure the house drains function properly before connecting the bathtub drain. Dual drain does not guarantee the fast drainage of the house drain if it’s not functioning properly.

Below is the Floor Drain Installation Option

Recessing the Drain Below the Subfloor Level and Cutting the Apron and End Panel
The levelling legs allow for the tub to be lowered, however, the bottom of the apron, end panel and the drain will hit the floor. It will be necessary to cut out access in the subfloor for the drain and cut the bottom of the apron and/or end panel (in case of a corner installation) for the tub to be lowered. If cutting the bottom of the apron or end panel is needed, use masking tape and appropriate cutting tools to avoid damage to the acrylic panel.

Warning: If this custom installation is done, the warranty will not cover the damaged or altered parts of the bathtub.

Door and Frame Adjustments

Prepare the subfloor for the drain and ensure that the area is level. The supporting sub-floor must be able to support the total weight of the bathtub, bather and water and must meet local construction code requirements. Use a level and make sure that the subfloor below the tub is levelled. If the floor is not perfectly level, adjust the appropriate levelling legs to re-align the tub to the perfect level. It is important that all of the leveling legs are completely supporting the tub
(touching the floor with equal weight distribution) and the tub is levelled for the door seal to work properly. If the tub is not perfectly leveled, it may cause frame and shell warping which can cause changes in door alignment resulting in water leakage and voiding the warranty.

DISCLAIMER : The frame specifications and configuration vary based on the model. If the sub-floor does not support the total weight of the bath, bather and water, it can result in warping of the shell, misalignment of the door and/or create leaks and could lead to damage to your home.

Your walk-in bathtub has been tested and levelled properly before leaving our facility. Our walk-in bathtubs have been set on a perfectly level surface to ensure no leaks and proper door closing. It is up to your installer to test and make any adjustments necessary to ensure that all levelling legs support the tub frame and that the door is aligned correctly to prevent any leaks. The door must close smoothly to create a water-tight seal. Extending or shortening the legs will help correct any alignment issues to close the gap between the door and the frame. Please call us immediately if any issues arise or if you have any concerns. 1-800-480-6850.

DISCLAIMER : The frame specifications and configuration vary based on the model. If the sub-floor does not support the total weight of the bath, bather and water, it can result in warping of the shell, misalignment of the door and/or create leaks and could lead to damage to your home.

Door and Frame Adjustments

WARNING: Failure to level the tub correctly WILL RESULT IN MISALIGNMENT! The drawings below illustrate some examples of what types of frame warping will occur if the legs are not level with the floor.

Service Access and Door Seal

It is the responsibility of the installer or owner to provide access for the service required, per code. Ella is not responsible for any costs related to obtaining access for repair. The owner shall assume responsibility for such costs, and if appropriate, must seek recovery from the installer. Do not insulate around the tub equipment. The tub, frame and all parts have been engineered to provide the proper ventilation. Any obstructions may cause the pumps or other electrical components to overheat.
Door Seal
Please keep in mind that the door has been closed for an extended period of time throughout shipping and the bathtub has been stored in various temperatures. It is possible for the silicone seal to stick to the frame when stored for extended periods of time. When the bathtub is received, the door seal should be checked for deformations from shipping and re-formed and adjusted where necessary. To restore the door seal, the seal must be released and allowed to relax with the door open. This is done by squeezing the seal with your fingertips and pulling it away from the door frame to regain its flexibility and original form. It is recommended that the door be kept open when not in use to increase the lifetime of the door seal and maintain its flexibility.

Reversible Extension Kit

Economy Dimensions: 7″W x 29 1/2″L x 371/2a”H

• L” Stainless Steel Brackets ………………………Qty
• (3) L” Acrylic Bracket ………………………………….Qty (1)
• 1″ x 1/8″ Bolts ………………………………………..Qty (7)
• 1″ x 1/4″ Bolts ………………………………………..Qty (7)
• 1″ Screw ……………………………………………….Qty (1)
• 1/2″ Nuts ……………………………………………….Qty (9)
• 3/8″ Nuts ……………………………………………….Qty (7)
• Medium Washers …………………………………..Qty
• (14) Small Washers ……………………………………….Qty (14) Plastic
• Washer ………………………………………Qty (1) Plastic
• Cap ……………………………………………Qty (1

1. Install 3 extension support brackets provides in the kit.
2. Clamp in place, the extension panel to the walk-in tub shell, lining up the facade of the top and front.
3. Pre-drill (+3/8″) slightly wider holes than mounting screws to allow for final adjustment to the panel.
4. Mount extension with 7 screws, washers and bolts.
5. Apply Silicone or white caulking as needed.

Side Panel Cutting Adjustments.

The side panel has to be cut 3/8″ to ensure a flush fit against the wall and proper side attachment with Velcro.

1. Overlap that needs to be cut.
2. Place tape over the side panel
3. Mark a line 3/8″ from top to bottom of the side panel.
4. Clamp down a metal straight edge to ensure a straight cut. then use a saw blade to cut the side panel.
5. Attach the side panel using Velcro

Side panel attachment was applied by pushing the Velcro tas together on the frame and inside of the side panel.

Finishing the Installation of the Walk-In Bathtub to the Wall

The walk-in bathtub can be installed and finished with tile or wall panels as shown in the image above. The walk-in bathtub deck design is flat, allowing for the tile or wall panel to overlap the tile flange and the deck for a proper seal and to have enough distance between the controls and the wall. It is suggested to install the tile flange to the edge of the bathtub with 100% silicone before pushing the walk-in tub against the wall into place. Any thin (1/8″ or 3/16″) rustproof and waterproof material like acrylic, thin stainless steel, or fibreglass strip can be used as a tile flange. A tile flange can also be supplied by a contractor (available online). The strip can be approximately 5″ tall, just enough to be glued to the edge of the tub and overlap the edge by 2″ giving enough water barrier. Silicone-based caulking must be applied to joints.
NOTE: Any alterations or installed additions are the responsibility of the installer. Ella Accessible Bathrooms is not responsible for any damage to the unit or for water damage, which could occur due to improper installation.

Operations Instructions

(If Applicable)

Entering the walk-in bathtub:

• The U-shape inward swing door handle is located on the inside of the tub and is designed for a safer entry with an added deck and a wall-mounted grab bar.
• Once you are in the tub, remain standing and close the door. While the door may be closed from a sitting position, it is much more difficult.

NOTE: Standard S-shape inward-swing Door Walk-In Bathtub with Hydro Massage Option Shown Above

Filling and Draining the Tub:

Open the drain by turning the handles clockwise, and close the drain by turning counter-clockwise. To avoid spills or leaks, do not fill the tub over the centre of the drain handle. Do not open the door unless the tub is completely drained!

Ella’s 5-piece Fast-Fill Faucet:

To turn the water on, turn the hot (marked red) or cold (marked blue) handle to your desired temperature. To turn the pullout hand-shower on, turn the diverter (middle lever) towards “OFF” and push down on the faucet lever.

NOTE: The hand shower has 5 water flow settings controlled by a dial.

Heated Seat & Back

Digital push control on the front face of the tub turns the heated seat/back On/Off. Make sure to only press one, pressing the button again will turn it off. Turn on 10-15 minutes prior to entry to allow the seat to heat up Turns off automatically after 20 minutes

Features

• Uses less energy than a standard light bulb
• Flexible, strong & uniquely safe
• Energy saving, reflective foil/foam insulation
• Hermetically sealed heating elements and connections
• Made in the USA
•  One-touch, individualized, comfort maintenance
• 20 minute automatic shut-off timer
• Splash-resistant housing for transformer and electronics
• Attractive LED “heatwave” display

Hydrotherapy System
Push Control Option: Push the ON/OFF control labelled “Water” to turn the hydro pump on. To turn it off, press it again. Adjusting the Water Massage Intensity: Turn the intensity dial control clockwise or counter-clockwise to adjust the water pressure to your liking. In-Line Water Heater: The in-line water heater will automatically turn on/off when the hydro pump is turned on/off. The purpose of the in-line water heater is to maintain the temperature of the water.

Cleaning and Maintenance

Before First Time Use
The Pump Circulation System needs to be flushed and drained before using Ella’s Walk-in Bathtub for the first time. To flush the bathtub, combine 2 cups of white vinegar and 2 cups of water. Then, fill the bathtub with water to reach an inch above the highest jets. Add the vinegar/water mixture, and run the bathtub for 10 minutes. Since the air and hydro system are plumbed, it is not necessary to flush after each bath. To remove construction debris, use a mild detergent. More stubborn debris may be removed with denatured alcohol or Clorox Soft Scrub cleaner. Additionally, light scratches and dulled areas may be restored to their original luster by polishing the surface with a fine grade, automotive type cleaning and polishing compound, such as Turtle Wax brand products.

Suggested Monthly Cleaning Instructions
It is recommended that the pump’s inlet cover is cleaned and the pump circulation system is flushed once a month. You can clean the pump’s inlet cover by clearing debris, such as hair, followed by wiping it down using a non abrasive towel and a suggested cleaning material (see below).

Suggested Cleaning Materials
We recommend cleaning your walk-in bathtub once a month using a 1:1 ratio of white vinegar and water. Combine 2 cups of white vinegar and 2 cups of water. Then, fill the bathtub with water to reach an inch above the highest jets. Add the vinegar/water mixture, and run the bathtub for 10 minutes. You may also use the following cleaning products on your Ella’s Walk-in bathtub:

• Dishwashing Detergent
• Lysol Power Bathroom Cleaner
• CLR Bath & Kitchen Cleaner
• Formula 409 All-Purpose Cleaner
• Iron Out Rust Stain Remover

ATTENTION:
We do not recommend using abrasive cleaners and cleaning materials. Additionally, avoid using bath bombs because they may be difficult to clean or clog the jet system(s). Bath oils, fragrances and salts may be used, however, these items are not suggested because it may require more frequent maintenance and cleaning of your bathtub and/or plumbing.

Warranty

Ella Acrylic Walk-In Bath Warranty Information

This limited lifetime warranty is extended to the first purchaser to be free from defects in workmanship and material under normal use and conditions from the date of the original purchase. This warranty is non-transferable and applies only to the original owner and to the original installation place – address only and does not extend to products previously used as display models or products that have been modified or repaired by anyone else but Ella’s Bubbles. The warranty is void if the ownership or original installation location is changed (the tub is relocated). This warranty relates to all fittings and components included with the tub from the manufacturer. The bathtub shell, frame, door seal, and finish are covered by a limited lifetime warranty. The door is covered by a limited lifetime warranty under normal use and conditions. All supporting equipment, motors, pumps, fixtures, electronic controls, faucets, waste, overflow, and all plated finishes, are covered by a limited five (5) year warranty. This warranty is non-transferable and applies only to the original owner. The finish warranty does not apply to fading, cracking, delaminating or blistering due to excessive wear, sun fading or scouring due to cleaning. This warranty shall not apply to any failure resulting from negligence, abuse, misuse, misapplication, alteration, modification or improper maintenance. The door warranty is valid only if the alignment of the door is not changed by applying pressure to the user’s weight holding the user’s weight to the door or by the wrong installation. The door is designed to hold its own weight and not designed to hold the user’s weight. Should service be required for any reason of any defect or malfunction of the product during the first five years, Ella’s Bubbles will ship the part to the original customer’s address without charge (subject to verification of the defect or malfunction). Ella’s Bubbles will not be liable for any incidental expenses or material charges in connection with the removal or replacement of the product or parts. Delivery time is based on parts availability and location. Normally parts are sent out immediately. Emailed or mailed photos of defective products and a description of the problem is required. defective product and a description of the problem is required.

• All mailing notifications must be sent via certified mail to: Ella’s Bubbles, LLC.
• 2101 S. Carpenter Street Chicago, IL 60608
• Email: info@ellasbubbles.com

The Manufacturer will not be responsible for any water damage to structures or property for any reason including but not limited to manufacturer defect or improper installation. The manufacturer will assume no responsibility for the loss of the system, inconvenience due to loss, damage to real or personal property or any other consequential damage. The manufacturer will not be liable for any incidental expenses or material charges in connection with the removal or replacement of the purchased part or any part or parts of the system. This warranty shall not apply to any type of failure resulting from negligence, abuse, misuse, misapplication, improper installation, alteration or modification, chemical corrosion or improper maintenance. There will be a charge for replacement parts or replacement of the entire electrical unit if the defective unit is returned for any of the reasons listed above. Ella’s Bubbles reserves the sole authority to make any type of warranties or representations concerning its products and will not be responsible for any warranties or representations made by any outside source including dealers, retailers, distributors or contractors. Ella’s Bubbles does not warrant the installation of any of our products. Items include all plumbing or electrical related connections, and improper or negligent installation of the product. Alteration made of, or alterations or modifications made to the system, may cause the product or the system to malfunction. Such problems are not covered by warranty.
TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
Ella’s Bubbles and Seller hereby disclaim any liability for special, incidental, or consequential damages. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You may have other rights, which vary from state/province to state/province.
Disclaimer: Limited lifetime parts warranty does not apply to thermostatic control valve (TCV).
TCV warranty is (1) year year-limited warranty that does not cover cartridge malfunction due to contaminated water with calcium, iron or other heavy particles in the water resulting in the cartridge getting stuck and TCV not operating properly. The TCV must be protected with a filter or mesh in the water lines which must be cleaned periodically. Ella’s Bubbles offers cleaning service for the cartridges for a nominal fee: labour + shipping. The cartridge cleaning is done at Ella’s Bubbles facility, or it can be done by the contractor hired by the customer. The removal and cleaning of TCV should only be performed by a licensed and insured contractor or plumber following online instructions. Non-Ella brand faucets are not covered under this warranty. Please refer to their own original manufacturer’s warranty.

Warranty Activation Form

Installer’s Information

• Name
• Address City State Zip
• Telephone / Email
• Date / Signature

Upon completing the installation of an Ella Walk-In Bath, the following Warranty Activation Form must be completed, signed by both the customer and installer, and returned to Ella’s Bubbles, LLC. In order for the Warranty to be activated (faxed, scanned, emailed, or hard copy mailed

The tub is level in all directions and all support legs are touching the ground.

• The tub is installed on a dedicated GFCI-protected circuit
• The frame of the tub has been properly grounded.
• The Door Seal has been cleaned with rubbing alcohol to remove any dust or debris left over from construction.
• Temperature Control Valve operated on both hot and cold settings.
• Both diverters function properly.
• Hand Shower functions on all settings without leaking.
• All supply lines have been checked for leaks while both diverters are on.
• Drains open and close properly, and the locking nut has been tightened on both stoppers.
• The door seal is water-tight after the tub has been filled for a minimum of 20 minutes.
•  After running for a minimum of 20 Minutes both the Hydro and Air Pumps are functioning properly and all connections to the pumps and jets are water-tight.
• Chromatherapy Light and the Ozone Sterilization are working properly. (When the Ozone is on by itself it will make a light humming noise).
• All drain fittings have been checked for leaks while the tub is draining.
• The unit is installed with access to both plumbing and electrical connections.

Owner’s Information

• Name
• Address City State Zip
• Telephone / Email
• Date / Signature

Model: ____ Serial Number: __ Purchase Date: _ Purchase Price: ___
Place of Purchase:

Contact Name: ____ Phone Number:

Copy of sales receipt must be included with warranty activation forms.

To activate the manufacturer’s warranty, please complete both pages and use one of the options below to submit.

• Via mail: Ella’s Bubbles, LLC.
• Warranty Department
• 2101 S. Carpenter St., Chicago, IL 60608
• Via fax: 1-312-666-3551
• Via email: warranty@ellasbubbles.com

IMPORTANT

Warranty Activation Form MUST be completed for both the Owner and Installer to validate the warranty. Failure to complete both pages (26 and 27) will void the warranty on this bathtub. Completed Ella Warranty Activation Forms can be emailed to

warranty@ellasbubbles.com, faxed to 312.666.3551, OR mailed to 2101 S. Carpenter St., Chicago, IL 60608

References

• Ellas Bubbles Walk In Tubs - Acrylic Bathtubs With Door
• Ellas Bubbles Walk In Tubs - Acrylic Bathtubs With Door

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>