Armacost LIGHTING 513115 ProLine Single Color LED Strip Light Controller Instruction Manual

: June 17, 2024
: Armacost LIGHTING

Table of Contents

Introduction
Receiver & wiring
Safety Protection
Specifications
Warranty
Customer support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Armacost LIGHTING 513115 ProLine Single Color LED Strip Light Controller

Armacost LIGHTING 513115 ProLine Single Color LED Strip Light
Controller

Introduction

This LED controller is designed to drive constant voltage single color LED products such as LED tape light or LED fixtures in a voltage range of 5–24 volts DC. The receiver works with the RF wireless remote control, which allows the user to adjust LED brightness.

Receiver & wiring

Input – from power supply
The controller input and output voltage range is 5–24 volts DC. Make sure the LED lighting voltage is within this range and below the rated wattage of the power supply. Connect input wires from the power supply to the controller as indicated by the polarity markings on the controller (+ to + and – to –).
Output – to LED lighting
Observe polarity indicated on the controller when connecting to LED lighting (+ to + and – to –). Make sure the voltage of the LED lighting is the same as the power supply and the maximum load doesn’t exceed that of the controller.
CAUTION: Shorting of output cables could cause permanent damage to controller. Make sure cables are well insulated from each other.
Controller status indicator
This light shows the controller status as follows:
Steady green: Normal operation
Single green blink: Command received.
Long single green blink: Mode or color cycle edge.
Long single yellow blink: Reach brightness limit.
Red flash: Overload protection.
Yellow flash: Over heat protection.
Green flash 3 times: New remote controller paired.
Wiring diagram
Connect the power supply to the controller input and the controller output to the LED lighting. The output voltage of the power supply must be the same as the voltage of the LED lighting. Make sure all power cables are connected securely and insulated before powering on.

Remote Control
On/Off
Press this key to turn on controller. Press and hold to turn off. The controller will remember the controller state when powered off, and will return to that state when powered back on.
Brightness adjustment
Press the “▲” and “▼” keys to adjust brightness.
Remote indicator
When pressing keys, the indicator blinks if the remote is working properly. If the indicator flashes slowly when pressing keys, battery power is low and it needs to be replaced. Replace with a CR2032 battery.
Remote control operation
Using the remote control
Pull out plastic battery insulation tab before use. The RF wireless remote will work through walls and doors. Do not install in a metal enclosure.
Pairing with a new remote control
The remote control and receiver are already paired, but up to five remotes can be paired to one receiver.
To pair a new remote:
To pair a new remote:
Disconnect power to receiver and wait five seconds.
Reconnect power.
Within ten seconds, press the ON/OFF and “▼” keys simultaneously for about three seconds.
De-pairing remotes
To de-pair a remote control, pair the remote you wish to continue using with the controller and any other paired remotes will be de-paired.

Safety Protection

The controller has a function to prevent it from being damaged by mis-wiring, output short circuit, overloading, or overheating. It will automatically shut down under these extreme conditions until safe operating conditions are restored. To avoid shutdowns, make sure the installed LED lighting is compatible with constant voltage, is in the rated range of the controller, and the cables are well connected and insulated. Also, install the controller with proper ventilation and heat dissipation in mind.

Specifications

Output mode …………………………………………… PWM constant voltage
Working voltage ………………………………………………………. 5–24V DC
Rated output current …………………………………………………….. 1x10A
Brightness grade ………………………………………………………..11 levels
PWM grade ………………………………………………………….. 4000 steps
Overload protection …………………………………………………………… Yes
Overheat protection …………………………………………………………… Yes
Remote frequency …………………………………………………. 433.92MHz
Remote control range …………………….. up to 50 ft./15m in open areas
Controller dimensions ………………………………3.41 X 0.95 X 0.58 in./
………………………………………………………………..87 X 24 X 14.5mm
Remote dimensions …………………………………..1.38 X 4.8 X 0.37 in./
…………………………………………………………………..122 X 35 X 9mm

Warranty

3-year limited warranty. This product is for dry location use only. Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void warranty. Proof of purchase is required for all returns. Questions? Email support@armacostlighting.com.