JMM SOLUTIONS T12 STC OLED Digital Soldering Station User Manual

JMM SOLUTIONS T12 STC OLED Digital Soldering Station

Conventional safety

• Please use only the power adapter that is dedicated to the product and is certified by the country/area.
• Do not operate in a wet environment.
• Do not operate in a flammable and explosive environment. Please keep the surface of the product clean and dry.
• To protect your family and friends for safety, please power off after use or leave, and beware of fire.
• When the host is starting up, the temperature of an iron tip will be reached 100℃ to 480 ℃, beware of scalds.
• Do not be soaked in water or with wet hands to use the soldering station, to prevent leakage.

Operating environment

Operating environment

|

Requirements

---|---
temperature| Working condition:+0℃ to +50℃
Off working state:-20℃ to +60℃

humidness

| Working condition: high temperature 40℃-60℃, 0%-60%RH
Working condition: low temperature 0℃-40℃, 10%-90%RH
Off working state: high temperature 40℃-60℃, 5%-60%RH
Off working state: low temperature 0℃-40℃, 5%-90%RH

Matters needing attention

• When using the T12 iron tip please tighten the nut for the soldering head to avoid falling and damaging the iron tip.
• The temperature will be reached above 350℃ if the soldering station is used for 40 minutes, and the temperature of the front end of the handle will be reached 50℃ -60℃.
• When the new T12 soldering iron tip is used for the first time, the Host will appear temperature jump and display ERROR, it will become a normal phenomenon due to the heating of the inner galvanic couple part of the iron tip. After repeated use several times, the temperature will be stable.

Parts List

1. T12-P9 Handle
2. Head of the iron tip
3. Nozzle tip
4. Aviation Plug of handle
5. OLED temperature display
6. Encoder

Product parameter

Working parameter

Install Iron Tip

• Slide the tip into the quick-release handle until it stops.
• The tip is held by friction and is now ready for use.

Note:
Turn on the button, and the display screen shows an ERROR, indicating that the iron tip may not be well installed, please try to install the iron tip again.

Description For Display

Note:
After confirming the installation of the components is right, the new iron tip is inserted into the handle and the display screen will be a flash or ERROR, and the host buzz is wrong. It’s normal. After heating for 5-20 minutes, it will return to normal gradually—The temperature control range of the ma min engine: is 200 °C -480 °C . The common welding temperature is 300 °C -380 °C. To protect the working life of the soldering iron tip, it is recommended that the temperature is not more than 380 °C!

Menu use

Enter the menu setting interface: under the normal working temperature interface, long press the encoder button (about 3s). Enter the host setup mode! Exit menu settings interface: at the menu setting interface, long press the encoder button (about 3s), exit the host setup mode!

Setting menu:

• Enter the function item: rotate the encoder to the corresponding function, and short-press the button to enter the function item.
• Exit setting function item: after setting the corresponding parameters with the encoder rotary knob, short press the button to confirm exit the function item.

Temperature calibration

After selecting the temperature calibration function, short press the encoder to enter the temperature calibration setting, the adjustable temperature ratio: is 70%-130%, if there is no professional measurement instrument, please set the ratio value to 100%.

Sleeping time

• Choosing the sleeping time feature, short press encoder, into the sleeping time setting, the time setting range: 0-99 minutes, if you don’t need the sleeping time function, the dormancy feature can be set to OFF.
• Default sleeping time for 1 minute, means after 1 minute the host and handle standing still, the soldering station will enter a dormant state, and the temperature of a soldering iron tip will drop to 150℃, at this time when the handle or rotary encoder, and the soldering station will rapidly heat the working temperature before Sleeping.
• You can set the sleeping time according to the usage scenario and working habit, it can extend the working life of the iron tip and protect your family and friends!

Power off time

• Choosing the power off time feature, short press encoder, into the power off time setting, the time setting range: 0-99 minutes, if you don’t need the power off time function, the power off function can be set to OFF.
• Default power off time for 1 minute, means after 1 minute the host and handle stand still, the soldering station will enter to power off time state, and the temperature of a soldering iron tip will drop to indoor temperature (note: The temperature control range of the host is 200- 480℃, it will appear larger deviation when the temperature less than 100℃. Please ignore it.). At this time when the handle or rotary encoder is used, the soldering station will rapidly heat up the working temperature before power off.
• You can set the power off time according to the usage scenario and working habits, it can be extended the working life of the soldering iron tip!

Strengthening Time

• After choosing to strengthen the time function, short-press the encoder and enter the time setting. The time setting range: is 0-99 minutes.
• The default time is 30 seconds, it can be set according to the actual needs, after setting, short press the encoder to confirm and exit. When working normally, it takes a short time to increase the temperature of welding the larger welding spot, it can be heated to the set temperature rapidly after pressing the encoder. After 30 seconds, the host will automatically return to its original temperature. This can avoid soldering iron tip oxidation when at high temperatures!

Strengthening temperature

• After choosing to strengthen the function of temperature, short-press the encoder, and enter the strengthening temperature setting, the temperature setting range: is 10-80 ℃.
• The default strengthen temperature is 30 ℃, it can be set according to actual needs, after setting, short press the encoder to confirm and exit. When working normally, it takes a short time to increase the temperature welding the larger soldering spot, it can be heated to the set temperature rapidly after pressing the encoder. After 30 seconds, the host will automatically return to its original temperature. This can avoid soldering iron tip oxidation when at high temperatures!

Wake-Up type

• After selecting the wake-up function, short press the encoder, and enter the setting of the wake-up type, the system provides two kinds of wake-up types: encoder together with handle or just encoder. When choosing encoder + handle, the soldering station is automatic power off, shaking handle or short press or rotary encoder, all can wake up the host!
• When choosing the encoder, the automatic shutdown state, short press or rotary encoder can wake up the host, but a shaking handle cannot wake up the host!
• The default setting is encoder + handle, which can be set according to actual needs.

Buzzer switch

This version OLED controller integrates with a buzzer, and the sound prompts the host state. The buzzer will beep when the host encounters an error or sets the appropriate function.

Battery guard

According to the voltage environment of the host, the built-in battery guard function of this soldering station, and the default voltage is 12V. When the voltage is not stable, the power supply will be supercharged according to the setting. Usually don’t need to set it. The setting range is 12V-24V.

Version information

It shows the information of this version controller.

Restore default

Restore the parameters of the soldering station to the factory default. Note: please back up your usual important parameters before you restore factory Settings to prevent data loss. For example: temperature calibration value, strengthening time and temperature, etc.

Iron tips maintenance

1. Please put the appropriate tin on the adhering head of the iron tip Before powering off, and please clean it before welding.
2. Do not allow the iron tip to stay at a high temperature for a long time to avoid dry burning.
3. In welding, do not rub the soldering tip with too much pressure to friction the solder, which will damage the iron head.
4. Never clean an iron head with a rough material or file.
5. If the surface oxide and not absorb tin, as needed you can use 600 to 800 of emery cloth friction it carefully and use isopropyl alcohol or equivalent solution to clean, heated to 200℃ immediately adhering tin to prevent sticking tin and then oxidation.
6. Do not use chlorine or high-acid soldering flux. Only use of synthetic resin or activated resin flux.
7. The working temperature of the soldering iron tip is about 300℃ to 380℃, and the working temperature should not exceed 450℃ in a short time. Otherwise, it will affect the working life of the soldering iron tip!
8. Different welding scenes should be selected with different soldering iron tips. Large welding spots or aluminium base plates will need to be touched to a large soldering iron tip (such as C4). Small welding spots can be usedC1, JL02, ILS, etc.
9. The new soldering iron tip is used for the first time, the heat up may be slightly slower, and it can melt in 7 seconds after the normal use of 1-3 hours.
   10.7 seconds of tin, only for solder wire with high purity and low melting point, the higher the lead tolerance, the speed of melting tin is, the higher the temperature will be required. So we suggest choosing the high purity & low melting point solder wire from my store.

After-sales service

T12 soldering station is provided with a 1-year warranty. For warranty service, please contact us. The iron tip is a consumable, following first use it can not be returned or replaced.

About Discarding

Do not discard in family garbage!

• Handling and recycling: you have to deal with the iron correctly according to local laws and regulations.

FAQ

1. Why the temperature of the new T12 solder tip is jump?

   • Because the inside heating core of the new T12 solder tip did not go through the high temperature, so the first time to use will be a bit of temperature, generally without special treatment, the normal use of 1-2 days after the basic will not bounce. Such as the need to immediately effective, the general proposal to adjust the temperature to 380℃ -400℃, side of the solder tip to the tip of the tin, burning 5-10 minutes after the shutdown, until the solder tip cooling and then re-boot! ( if 1 time no effect, then can be repeated 2-3 times). T12 is pulsating temperature warming, even if the display temperature is flashing, the tip of the real temperature is completely stable.
   • T12 jump temperature also is connected with the temperature control board of procedures, power of electrostatic and if it connects to the ground.

2. What is the problem of attention when we use the T12 first time?

   • The T12 tip heating speed is very fast, when the new solder tip connects the electricity, it must be input immediately to the solder tip, for protection, due to heating up fast, just needs 6-10 seconds, and more time for you to preparation.
   • So the important is to prepare the items that will be welded, and finally boot power, and each welding gap or the end should be more on the tin to protect and then shut down, so it can avoid in the new sold tip difficult, especially the T12 tip type of iron, such as T12-I / T12-IL / T12-BL / T12-ILS and so on!

3. What are the precautions for using the T12 tip?

   • If can use low temperature, then do not high temperature: T12 is constant temperature control, and the generally recommended working temperature control is between 300℃ ~ 380℃, higher than 380℃ damages the coating of the solder tip and cuts down the PTC life!
   • Do not dry: the first time to use the solder tip should be wrapped while heating a layer of tin. If it’s without work, at once shut down!
   • Diligent to clean: before shutting down, use a wet sponge or detin the ball to remove the tip of the oxidation of debris, on the tin after the shutdown power off!
   • Standard operation: Do not violent collision the solder tip, do not stamp the top of the hard objects, but can not be used to hot plastic and other materials, specifically remind that friends like tin should avoid iron and other hard metal knock tin, the heating core of T12 is in the head of the solder tip, often percussion is a fatal damage to T12!
   • Less use of scaling powder: scaling powder can not be used, can be used as little as possible! When scaling powder helps make beautiful and reliable welding at the same time, but also greatly speeds up the consumption of the coating of the solder tip, the T12 heating core high-temperature position is very near the Nozzle tip of the solder tip, Scaling powder in the fear of threat to T12 head pressing parts.

4. What to do when the T12 tip does not absorb tin?
   T12 iron head does not absorb tin, generally, there are two reasons:

   • The head of the solder tip is in severe oxidation and can not absorb tin.
   • Temperature can not rise then can not tin.
   • The head is oxidized and can not the tin, you can use the soldering iron to clean the ball gently, then use the wet sponge rub and then heat the tin.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>