TOSHIBA RAS-25S4KVPG-ND Air Conditioner Owner’s Manual

TOSHIBA RAS-25S4KVPG-ND Air Conditioner

Specifications:

• Product: Air Conditioner (Split Type)
• Indoor unit model: RAS-25, 35S4KVPG-ND
• Outdoor unit model: RAS-25, 35S4AVPG-ND
• Manual Languages: EN/SV/FI/NO/DA/EE/LV/LT

Product Usage Instructions

Precautions for Safety:

Read the precautions carefully before operating the unit. The appliance is filled with R32 refrigerant. Follow all safety instructions provided in the manual to ensure safe operation of the air conditioner.

Danger:

• Do not attempt to install, repair, open, or remove the cover yourself to avoid exposure to dangerous voltages. Seek professional assistance for such tasks.
• Turning off the power supply does not eliminate the risk of electric shock. The appliance must be installed following national wiring regulations.
• The appliance should be stored in a room free from continuous ignition sources.

Warning:

• Avoid direct exposure of your body to cool or warm air for an extended period.
• Avoid inserting fingers or objects into the air inlet/outlet of the unit.
• If any abnormality like a burning smell occurs, stop the air conditioner immediately and disconnect the power supply.

Product Usage:

Ensure proper installation, maintenance, repair, and removal of the air conditioner by qualified personnel only. Follow the guidelines provided in the manual for safe and efficient use of the product.

FAQs

• Q: Can children use this appliance unsupervised?
  • A: This appliance can be used by children aged 8 years and above if they have been given proper supervision or instruction on safe usage. Cleaning and maintenance should always be supervised by adults.

“`

OWNER’S MANUAL

R32
ENGLISH SEVNEGNLSISKHA ENSGULOISMHI ENNGOLRISHK ENDGALNISHK ENGELEISSTHI ELANTGVLIISSKHI LEINEGTULIVSIH

Scan QR CODE to access installation and owner’s manual on website. https://www .toshiba-carrier.co.th/manuals/default.aspx
Manual are available in EN/SV/FI/NO/DA/EE/LV/LT.

AIR CONDITIONER (SPLIT TYPE)
For general public use
Indoor unit RAS-25, 35S4KVPG-ND
Outdoor unit RAS-25, 35S4AVPG-ND

1134050203

PRECAUTIONS FOR SAFETY

Read the precautions in this manual carefully before operating the unit.

This appliance is filled with R32.

Warning indications on the air conditioner unit

Warning indication

Description

CAUTION

CAUTION

BURST HAZARD Open the service valves before the operation, otherwise there might be the burst.

BURST HAZARD
Open the service valves before the operation, otherwise there might be the burst.

Keep this manual where the operator can easily find it. Read the precautions in this manual carefully before operating the unit. This appliance is intended to be used by expert or trained users in shops, in light
industry and on farms, or for commercial use by lay persons. The precautions described herein are classified as DANGER, WARNING and
CAUTION. They both contain important information regarding safety. Be sure to
observe all precautions without fail.

DANGER
Do not install, repair, open or remove the cover. It may expose you to dangerous voltages. Ask the dealer or the specialist to do this.
Turning off the power supply will not prevent potential electric shock. The appliance shall be installed in accordance with national wiring regulation. Means for disconnection from the supply having a contact separation of at least
3 mm in all poles must be incorporated in the fixed wiring. The appliance must be stored in a room without continuously operating ignition
sources (for example, open flames, an operating gas appliance or an operating electric heater). In order to avoid fire, explosion or injury, do not operate the unit when harmful gases (e.g. flammable or corrosive) are detected near the unit.
WARNING
Do not expose your body directly to cool or warm air for a long time. Do not insert your finger or any article into the air inlet/outlet. When an abnormality (burning smell, etc.) occurs, stop the air conditioner and
disconnect the power supply or turn off the breaker. This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

1

PRECAUTIONS FOR SAFETY

This appliance is not intended for use by person (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

EN

The air conditioner must be installed, maintained, repaired and removed by a

qualified installer or qualified service person. When any of these jobs is to be

done, ask a qualified installer or qualified service person to do them for you.

Children should be supervised to ensure that they do not play with the

appliance.

Do not use any refrigerant different from the one specified (R32) for complement

or replacement. Otherwise, abnormally high pressure may be generated in the

refrigeration cycle, which may result in a failure or explosion of the product or an

injury to your body.

Do not use means to accelerate the defrosting process or to clean, other than

those recommended by the manufacturer.

The appliance shall be stored in a room without continuously operating ignition

sources (for example: open flames, an operating gas appliance or an operating

electric heater).

Be aware that refrigerants may not contain an odour.

Do not pierce or burn as the appliance is pressurized. Do not expose the

appliance to heat, flames, sparks, or other sources or ignition. Else, it may

explode and cause injury or death.

Do not add any other devices without factory advice.

CAUTION
Do not wash the unit with water. It may cause an electric shock. Do not use this air conditioner for other purposes such as preserving food,
breeding animal, etc. Do not step or put anything on the indoor/outdoor unit. It may cause an injury or
damage the unit. Do not touch aluminium fin because it may cause an injury. Before cleaning the unit, turn off the main switch or the circuit breaker. When the unit won’t be used for a long time, turn off the main switch or the
circuit breaker. It is recommended that maintenance be performed by a specialist when the unit
has been operated for a long time. The manufacturer shall not assume any liability for the damage caused by not
observing the description of this manual. Remote controller and Holder are contained with magnet please keep far from
product that effect with magnet. (such as electronics appliance magnetic strip
card and etc.) High temperature, high magnet field and direct force collisions may effect to
magnet force down.

2

INDOOR UNIT DISPLAY

1 ECO (White) 2 Wi-Fi access (White) 3 Strong defrost (White) 4 Timer (White) 5 Operation Mode
– Cool (Blue) – Heat (Orange)
Display brightness can be adjusted, follow procedure on “.

2 PREPARATION BEFORE USE

Preparing Filters
1. Open the air inlet grille and remove the air filters. 2. Attach the filters. (see detail in the
Installation Manual).

Loading Batteries (when use wireless operation.)
1. Remove the slide cover. 2. Insert 2 new batteries (AAA type)
following the (+) and (­) positions.

Remote Controller Reset 1. Remove the batteries.

2. Press

.

3. Insert the batteries.

AIR FLOW DIRECTION

1 Press

: Move the

louver in the desired vertical

direction.

2 Press

: Move the

louver in the desired horizontal

direction.

Press

: For select

louver setting operation.

Vertical (Up-Down) Swing

Swing off

V

Vertical (Up-Down) Swing

H

Horizontal (Left-Right) Swing

Horizontal (Left-Right) Swing

3

V H

Vertical and Horizontal Swing

HADA Care Flow
H.DA

HADA Care Flow

Air flow upward to the ceiling, provide indirect air flow to body and homogenize room temperature.
Note: During HADA Care Flow mode, FIX button cannot active. Do not move the louver manually by hands or others. The louver may automation positioning by some operation mode.

REMOTE CONTROLLER

1 Infrared signal emitter

1

2 Start/Stop button

3 Mode select button

4 Temperature button

5 Fan speed button

6 Menu select button

7 Swing louver button

8 Exit button

9 Set louver Up-Down button

! Set louver Left-Right button

” Check button*

2

4

*Check button under battery cover
3

MODE

5

FAN MENU

6

7

SWING EXIT

8

FIX FIX

COOLING / FAN ONLY OPERATION

1. Press

: Select Cool , or Fan only .

2. Press

: Set the desired temperature. Min. 17°C, Max. 30°C.

Fan Only: No temperature indication.

3. Press MED+

: Select AUTO, LOW , LOW+ , MED ,

, HIGH

or Quiet .

AUTOMATIC OPERATION

To automatically select cooling, heating, or fan only operation.

1. Press

: Select Auto A.

2. Press

: Set the desired temperature. Min. 17°C, Max. 30°C.

3. Press MED+

: Select AUTO, LOW , LOW+ , MED ,

, HIGH

or Quiet .

HEATING AND 8°C OPERATION

1. Press

: Select Heat .

2. Press

: Set the desired temperature. Min. 5°C, Max. 30°C.

• Temperature range 5-16°C is Heat mode with 8°C operation with less of energy usage.

3. Press MED+

: Select AUTO, LOW , LOW+ , MED ,

, HIGH

or Quiet .

Note: During 8°C mode active (temperature range 5-16°C), some operation such as QUIET, Hi POWER, TIMER OFF cannot use.

8 DRY OPERATION

For dehumidification, a moderate cooling performance is controlled automatically.

1. Press

: Select Dry .

2. Press

: Set the desired temperature. Min. 17°C, Max. 30°C.

Note: DRY mode fan speed is set to Auto only.

3

MENU SETUP

For select more setting of Air conditioner such as Direct Air/Indirect Air,

Hi POWER, OFF Timer and other use MENU button

.

9.1 DIRECT AIR AND INDIRECT AIR OPERATION

Thermal sensors detect the human inside the room to finding the position of human and determine the louver operation to the airflow direction that user require. (except in DRY and FAN ONLY mode)

Direct Air
When the thermal sensor detects the human position The air conditioner adjusts the louver to Direct Air the air flow towards the human.

EN

Indirect Air
When the thermal sensor detects the human position The air conditioner adjusts the louver to Indirect Air the air flow of the human.

Direct Air/Indirect Air operation setting 1. Press MENU button for enter menu selection.

Blink both triangle and feature mark Feature not yet set.

2. Enter Direct Air/Indirect Air set by press MENU button. triangle mark will stop blink and setting feature will be blink instead.
Blink only feature

3. Select Direct Air/Indirect Air operation by press TEMP. button.

Direct Air Indirect Air None
4. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.
When feature had selected will return to menu selection display triangle mark will blink . 5. Leave from menu setting display by press EXIT button.
Note: Do not move the thermal sensor manually by hands or others.
This may cause malfunction of the thermal sensor. Constrains at the following condition cannot be detected Person be along the wall. Person be directly under the air conditioner. Where any obstacle such as furniture, other heat source. Place that room temperature is too high. A person wears heavy clothes and his/her skin is not exposed. A heating element of which temperature changes significantly is present. Some heat sources, such as a small child or pet may not be detected. A heat source is too far from air conditioner. A heat source does not move for a long time. Detection may mistakes from other heat sources, sunlight, fireplace,
radiator, moving curtains, etc.
4

9.2 MOTION TRACKING OPERATION To automatically control room temperature to save energy when have not occupancy inside the room or increase the ability to adjusts the air conditioning to suit the movement or activities that detected in the room. (except in DRY and FAN ONLY mode) 1. Press MENU button for enter menu setting and press TEMP. button to
select Motion Tracking feature.
Blink both triangle and feature mark Feature not yet set.
2. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.
When feature had selected will return to menu selection display triangle mark will blink . 3. Leave from menu setting display by press EXIT button.

9.4 SILENT OPERATION (Outdoor Unit)
Keep outdoor unit operating silently to ensure either yourself or neighborhood will have a tight sleep in nighttime. By this feature, the cooling or heating capacity will be optimized to deliver such silent experience. The silent operation can be selected from one of two purposes (Silent 1 and Silent 2). There are three setting parameters: Standard level > Silent 1 > Silent 2
Silent 1:
Though operating silently, the cooling or heating capacity is still prioritized to ensure having sufficient comfort inside the room.
This setting is a perfect balance between the cooling or heating capacity and the Sound level of outdoor unit.
Silent 2:
Compromising the cooling or heating capacity to the Sound level in any circumstance where the outdoor unit’s sound level is highly prioritized.
This setting has a purpose to reduce the maximum sound level of outdoor unit by 4 dB(A).
Note: While activating of Silent operation, inadequate cooling or heating capacity
may occur.
Silent Operation Setting
1. Press MENU button for enter menu setting and press TEMP. button to select Silent.
Blink both triangle and feature mark Feature not yet set.

Note: The human detection may be an error occur if there is a lot of sunlight
inside the room.
9.3 STRONG DEFROST OPERATION
Upgrade defrost ability when normal defrost ability is not enough by increase defrosting finished operation. 1. Press MENU button for enter menu setting and press TEMP. button to
select Strong defrost feature.
Blink both triangle and feature mark Feature not yet set.

2. Enter SILENT set by press MENU button. triangle mark will stop blink and setting feature will be blink instead. Blink only feature
3. Select SILENT operation by press TEMP. button.

2. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.
When feature had selected will return to menu selection display triangle mark will blink . 3. Leave from menu setting display by press EXIT button.

SILENT#1 SILENT#2 None
4. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.
When feature had selected will return to menu selection display triangle mark will blink . 5. Leave from menu setting display by press EXIT button.

Note: Strong defrost will operate only in Auto and Heat mode.
5

9.5 Hi POWER OPERATION To automatically control room temperature and airflow for faster cooling or heating operation (except in DRY and FAN ONLY mode). 1. Press MENU button for enter menu setting and press TEMP. button to
select Hi POWER.
Blink both triangle and feature mark Feature not yet set.
2. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.
When feature had selected will return to menu selection display triangle mark will blink . 3. Leave from menu setting display by press EXIT button.

9.7 FIREPLACE OPERATION

Keep indoor unit’s fan blowing continuously during thermo off, to circulate heat from other sources over the room. There are three setting parameters:
Default setting > Fireplace 1 > Fireplace 2

Fireplace 1:

During thermo off period, the indoor unit’s fan will continue to run by the same speed, previously selected by end-user.
Fireplace 2:

EN

During thermo off period, the indoor unit’s fan will continue to run at super- low speed, programmed from factory.

Fireplace Operation Setting
1. Press MENU button for enter menu setting and press TEMP. button to select FIREPLACE.

Blink both triangle and feature mark Feature not yet set.

2. Enter FIREPLACE set by press MENU button. triangle mark will stop blink and setting feature will be blink instead.
Blink only feature

9.6 ECO OPERATION To automatically control room temperature to save energy (except in DRY and FAN ONLY mode). 1. Press MENU button for enter menu setting and press TEMP. button to
select ECO.
Blink both triangle and feature mark Feature not yet set.
2. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.

3. Select FIREPLACE operation by press TEMP. button.

FIREPLACE1 FIREPLACE2

None

4. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.

When feature had selected will return to menu selection display triangle mark will blink .
3. Leave from menu setting display by press EXIT button.

When feature had selected will return to menu selection display triangle mark will blink .
5. Leave from menu setting display by press EXIT button.

Note:
Cooling operation; the set temperature will increase automatically 1 degree/hour for 2 hours (maximum 2 degrees increase). For heating operation the set temperature will decrease.

Note: While Fireplace operation on heating mode, indoor unit fan always runs
and cold air breezing might be occurred. Fireplace will operate in Heating mode only.

6

9.8 TIMER OFF OPERATION To set the timer OFF when the air conditioner is operating. 1. Press MENU button for enter menu setting and press TEMP. button to
select TIMER OFF.
Blink both triangle and feature mark Feature not yet set.
2. Enter TIMER set by press MENU button. triangle mark will stop blink and setting feature will be blink instead.
Blink only hrs
3. Select TIMER OFF by press TEMP. button. Can select TIMER OFF from 0.5 – 12 hrs.

9.9 PURE (IONIZER) OPERATION
Capture efficiency of floating impurities in the air is accelerated by Ionizer contaminates such as bacteria, odor, smoke, dust and virus are caught and deactivated by Ionizer. 1. Press MENU button for enter menu setting and press TEMP. button to
select PURE.
Blink both triangle and feature mark Feature not yet set.
°C
2. Confirm selected feature by press MENU button again.
Blink only triangle Feature already set.
°C
When feature had selected will return to menu selection display triangle mark will blink . 3. Leave from menu setting display by press EXIT button.

4. Confirm TIMER OFF by press MENU button.
Blink only triangle Feature already set.
When feature had selected will return to menu selection display triangle mark will blink . 5. Leave from menu setting display by press EXIT button.

°C
Note: Ionizer operation does not remove harmful substances from cigarette
smoke (carbon monoxide etc.). Open a window occasionally for ventilation. Build up of dirt, smoke, or an extremely humid environment might cause
the Ionizer operation to be malfunction. In that case, cleaning the air-con and let it dry prior operation are recommended.

Note: The setting will be saved for the next same operation.
Cancel TIMER OFF 6. During TIMER OFF already set (no.5) press MENU button and press
TEMP. button to select TIMER OFF.
Blink only triangle Feature already set.
7. Press MENU button again will cancel TIMER OFF.
Blink both triangle and feature mark Feature not yet set.
8. Leave from menu setting display by press EXIT button.

7

9.10 POWER-SELECTION OPERATION This function is used when the circuit breaker is shared with other electrical appliances. It limits the maximum currenl and power consumption to 100%, 75%, of 50% and can be implemented by POWER- SELECTION. The lower percentage, the higher saving and also longer compressor lifetime. Note: Due to the reason that POWER-SELECTION function limits the maximum
current, inadequate cooling or heating capacity may occur. 1. Press MENU button for enter menu setting and press TEMP. button to
select POWER-SEL.
Blink only triangle
2. Enter POWER-SEL setting by press MENU button again.
Blink only feature
3. Select POWER-SEL level by press TEMP. button.

100%

75%

50%

4. Confirm POWER-SEL level by press MENU button.
Blink only triangle Feature already set.

When feature had selected will return to menu selection display triangle mark will blink .
5. Leave from menu setting display by press EXIT button.

MANUAL DEFROST OPERATION

To defrosting the heat exchanger of the outdoor unit during Heating operation.

Press and hold

: for 5 seconds, then remote controller display

will show as picture 1 for 2 seconds.

11

DISPLAY LAMP BRIGHTNESS ADJUSTMENT

To decrease the display lamp brightness or turn it off.

1. Press and hold

for 3 seconds until brightness level ( , ,

or ) is shown on remote controller LCD then release the button.

2. Press

Rise
or
Decrease

to adjust brightness in 4 levels.

EN

Remote controller
LCD

Operation display

Brightness

Lamp illuminates full brightness.

100%

Lamp illuminates 50% brightness.

50%

Lamp illuminates 50% brightness and the operation lamp is turned off.

50%

All lamps are turned off.

All turned off

In the examples of going off.

and , the lamp illuminates for 5 seconds before

AUTO RESTART FUNCTION SETTING

This product is designed so that, after a power failure, it can restart automatically in the same operating mode as before the power failure.
Information
The product is shipped with Auto Restart function in the ON position. Turn it OFF if this function is not required.
How to turn OFF the Auto Restart Function
Press and hold the [OPERATION] button on the indoor unit for 3 seconds (3 beep sounds but OPERATION lamp does not blink).
How to turn ON the Auto Restart Function
Press and hold the [OPERATION] button on the indoor unit for 3 seconds (3 beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).
Note: In case of ON timer or OFF timer are set, AUTO RESTART OPERATION
does not activate.

13

SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the

button is pressed once during “Cool” or “Dry” mode,

the fan will continue to run for other 30 minutes, then it will turn off automatically. This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the 30 seconds.

more 2 times within

14 TEMPORARY OPERATION

In case of the misplaced or discharged remote controller.

Pressing the RESET button, the unit can start or

stop without using the remote controller.

OPERATION RESET

Operation mode is set on AUTOMATIC operation,

preset temperature is 24°C and fan operation is

automatic speed.

OPERATION / RESET Button

1

8

15 REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON. 2. Point the remote control at the indoor unit.
3. Push and hold button on the back side of Remote Control “00” will be shown on the display. (Picture 1)

4. Press

during pushing . “B” will show on the display and

“00” will disappear and the air conditioner will turn OFF. The Remote Control B is memorized. (Picture 2)
Note: 1. Repeat above step to reset Remote Control to be A. 2. Remote Control A has not “A” display. 3. Default setting of Remote Control from factory is A.

1

2

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated for 3 minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before the heating operation starts.
3. Warm air control: When the room temperature reaches the set temperature, the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation. 5. Heating capacity: Heat is absorbed from outdoors and released into
the room. When the outdoor temperature is too low, use another recommended heating apparatus in combination with the air conditioner. 6. Consideration for accumulated snow: Select the position for outdoor unit where it will not be subjected to snow drifts, accumulation of leaves or other seasonal debris. 7. Some minor cracking sound may occur when unit operating. This is normal because the cracking sound may be caused by expansion/contraction of plastic. Note: Item 2 to 6 for Heating model.
Air conditioner operating conditions

Operation Heating Cooling Dry

Temp. Outdoor Temperature
­30°C ~ 24°C ­15°C ~ 46°C ­15°C ~ 46°C

Room Temperature
Less than 28°C 21°C ~ 32°C 17°C ~ 32°C

17 MAINTENANCE

Firstly, turn off the circuit breaker.
Indoor Unit and Remote Controller Clean the indoor unit and the remote controller with a wet cloth when needed. No benzine, thinner, polishing powder or chemically-treated duster.
Air filters Clean every 2 weeks.
1. Open the air inlet grille. 2. Remove the air filters. 3. Vacuum or wash and then dry them. 4. Reinstall the air filters and close the air inlet grille.

TROUBLESHOOTING

The unit does not operate.
The power main switch is turned off.
The circuit breaker is activated to cut off the power supply.
Stoppage of electric current. ON timer is set.

Cooling or Heating is abnormally low.
The filters are blocked with dust. The temperature has been set
improperly. The windows or doors are opened. The air inlet or outlet of the outdoor unit
is blocked. The fan speed is too low. The operation mode is FAN or DRY. POWER SELECTION function is set
75% or 50% (This function is depend
on remote controller).

9

19 WIRELESS LAN CONNECTION

Toshiba Home AC Control

Toshiba Home AC Control application support

Please visit the application store on your device to download and install Toshiba Home AC Control application.

iOS : 9.0 or later.

Application Keyword : Toshiba Home AC Control

EN
Android : Version 5.0 or later.

About Toshiba Home AC Control
1. Toshiba Home AC Control can control AC operation by Smartphone or tablet (mobile device) via internet connection.
2. Everywhere control, control software run on Cloud system and mobile device can set and monitor AC operation via internet connection.
3. Everyone can control, 1 Wireless adapter maximum 5 User (use 1 email register).
4. Multi AC system control, 1 user can control 10 AC. 5. Group control.
5.1 Can create and control 3 groups of AC. 5.2 Can control max 10 AC per group. Note: 1. Adapter can register only 1 email address, if register with new email, current email will be invalid. 2. 1 email address can use for register 5 devices for control same AC.
Register process
Open an application and follow register for User registration.

1 Tab Register.

Italy United Kingdom

2 Enter email address.

3 Select country.

4 Enter user name.

5 Enter password by

6 Check for term and condition.

6-10 characters, combination

of alphabet and number.

7 Confirm information.

8 Information will be submitted to email, click link to confirm.

10

Log in to Toshiba Home AC Control application 1 Connect Wireless adapter to A/C and turn on power supply.
Built-in type, Wireless adapter already install with unit.

2 Open application and select Log in.

3 Enter user name and password.

4 Login successful.

Add Wireless adapter for control by Toshiba Home AC Control application

Wireless adapter Built-in
Active Wireless adapter by remote controller and Auto log in

1 Select “Add AC (Adapter)” from both display above.

2 Select AC (adapter) connection method.

*Note
1. In case of Wi-Fi router change or Email for register change need to re- process for add Wireless adapter again (Built in type : Press MODE button at Remote controller 5 seconds for active AP mode).
2. In case of change Wireless adapter to use with other A/C need to factory reset and re-process for add Wireless adapter again (Built in type : Press MODE button at Remote controller 5 seconds and select “rb”).

11

Add Wireless adapter for control by Toshiba Home AC Control application

3 AC (adapter) connect.

4 Active Wireless adapter by Remote controller.
Press and hold MODE button 5 seconds

EN

Wireless LED mark will blink when AP mode active

6 A/C add finished.

WPS mode

5 Connect with Home Wi-Fi Router.

Manual input
Wi-Fi Router Name Wi-Fi Router Password

7 Connect successfully. Wireless LED lamp stop blink. 12

Toshiba Home AC Control application Home screen
Menu

Weekly schedule

Setting

All AC On/Off Group AC On/Off
Each AC On/Off
Group name
AC device is offline
Notification ERROR code description (pop up)

Add AC
Sub menu all AC · Add Group · Delete Group · Operation Setting
Sub menu group · Select AC · Change Name · Operation Setting
Sub menu AC · Operation Setting · Change Name · Delete AC Setting temperature / Actual room temp
Current operation mode of each AC

13

Mode and Condition setting

Enter operation mode of All AC
EN
Enter operation mode of Group AC
Enter operation mode of each AC

Mode select for Toshiba Home AC Control application

Provide for 5 operation modes

Auto

Cool

Dry

Heat*

Fan only

Off

• This “Heat mode” is only available for Heat Pump product.
  14

Setting in operation mode Smart Sensing set

Mode select

Tab for select AC Weekly schedule OFF-ON Timer set 0.5 – 12 Hrs.

On Smart sensing

Select Direct Air/Indirect Air or Motion Tracking

Fan speed

Temperature set

On timer set from Off mode only

Indoor temperature Outdoor temperature

Louver set

Off mode

Special feature

15

Group operation Maximum 3 groups 1 Group maximum = 10 units. Add group
EN
Add AC in group

Delete AC in group

Please make sure Factory Reset is performed before deleting AC from mobile application. (See owner manual “Press and hold MODE button on remote control for 5 second and active dL function”)
16

Weekly schedule set
Day select Monday – Sunday Weekly schedule of all AC unit

Weekly schedule of all AC unit

Time select

Weekly schedule set for each unit

Mode select

Select program for active by tick at select box Weekly schedule cancel
Weekly schedule not set Weekly schedule set but not active Weekly schedule set and active
17

Energy monitoring

Select Room for Energy monitoring
EN

1 Select Energy monitoring.

2 Energy monitoring display.

Set cost calculate and currency

Select Energy monitoring display

Export data and send by Email
The power consumption displayed is just an estimate as it is calculated simply. It may sometimes differ from the result measured by the power meter. 18

In case of have some problem can check from Help menu
Note: The Wireless Adapter must be installed, maintained, repaired and removed by a qualified installer or qualified service person. Contact dealer and/or service center when equipment is malfunction.

References

• CTC | Manuals Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>