MERIDIAN Dual Sided Kiosk Solution Instruction Manual

MERIDIAN Dual Sided Kiosk Solution

Multi Views

ISO

REAR

LEFT SIDE

RIGHT SIDE

Opening Doors

To open the front door, insert small Blue key. Make sure the key is inserted all the way in and turn to the right. Once the key all the way to the right, pull out and remove the inner lock barrel.

Next insert the large T-Handle and turn right to unlock.

Cell Antenna

The cell antenna is located under the upper canopy. The wires will route down through the chassis and in the cradle point router, located inside the kiosk

Eye Bolt View

Install supplied eye bolts for lifting kiosk into position. Screw down so all four eyes are roughly the same height to avoid twist or canter in the kiosk while lifting

Mounting Bolt Hole, Location, and Access

Using a lift or sorts, lift the kiosks via the eye bolts mounted in the top of the unit. Place over the top of the concrete sleeve anchors installed in your pad.
Then install internal washers over studs and apply nuts. Tighten these down to specs to ensure the kiosks is securely fastened.

After Installing Mounting Hardware

After installing the kiosk into position and tightening down the mounting hardware, install the canopy or flat plate on top of the kiosk. This is supplied with studs that when placed on top, will protrude downward into the top area. The supplied nuts can be removed and re-applied. Tighten these down to allow a tight fit between the canopy base flanges and the chassis to keep any water ingress out.

Incoming Power Service Location

The rectangular cutout in the lower base plate is where the incoming power and data lines will enter the kiosk. They will route up the side wall “ behind the side wall braces “ and into the power disconnect lock-out box.

120 VAC 20amp circuit is required.

Incoming Data Line Location

The Data line will enter the kiosk via the rectangular cutout in the base plate and route through the rubber grommet in the plate shown here and into the route. From there the data is transferred into the PC via the installed Ethernet cable.

Installing the Monitors

The installation is the same for each side.

With the doors open, remove the side panels, marked in blue in Figure 1.1.

Next remove the large monitor bracket colored in blue in Figure 1.2

Bolt the supplied bracket to the rear of your monitor with the adjusting bolts towards the top of the monitor.

Lift and set the monitor with bracket onto the channel pictured here and place the retaining nuts on to assure it is secure and tighten nuts.

The adjusting bolts are to allow adjustment in the horizontal alignment of your monitor.

If need, loosen or tighten very just a little to change the alignment.

If you need to adjust vertically, simply loosen the support nuts you just installed, and slide left or right and retighten nuts.

Door Alignment Arms and Rollers

The door alignment, helper system is installed in the upper and lower side of the lock side of the kiosk. As the door arrives close to the closed or locking position, the arms ride on top of the rollers to help align the door.

Door Locking System

The door locking system has the centrally located lock on the side of the chassis. As the lock is turned via the 10mm hex key supplied, the action pulls the two rods, upper and lower, out of the tray show in this view. As the door is pushed close the opposed action with the hex key pushes the roller on each end of the rods into position and pulls the door closed.

Kiosk Base Mounting Layout

This is the kiosk base layout that shows the dimensions and layout for mounting holes and wire cutout.

Kiosk Graphics

The Graphics are placed in multiple places around the kiosk. If for any reason these get damaged due to usage, please contact Meridian for replacements.

Please contact Meridian for any questions or concerns about the unit

QUALITY + CERTIFICATION

Meridian promises a level of quality that goes beyond the expected. We control every step of our process from concept to completion, overseeing quality, design, cost and timelines. Many of our products can be UL Listed through UL self certify and our processes are ISO 9001:2015 certified.

Customers Support

© Meridian Kiosks | 312 S Pine Street, Aberdeen, North Carolina 28315 | MeridianKiosks.com

Phone: 910-944-1757 Ext. 2
Email: help@mzero.com

Corporate Headquarters
312 S. Pine Street,
Aberdeen, NC 28315
910-944-1751 ext. 2
Help@mzero.com
Meridiankiosks.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>