BLACK DECKER AP3560-B5 Air Purifier User Manual

: June 9, 2024
: Black Decker

BLACK DECKER AP3560-B5 Air Purifier

BLACK-DECKER-AP3560-B5-Air-Purifier-PRODUCT

OVERVIEW

BLACK-DECKER-AP3560-B5-Air-Purifier-FIG-1

CONTROL PANEL (1)

DISPLAY (2)

For Control panel & Display refer page number 5 for detailed explanation

Intended use

Your BLACK+DECKERTM AP3560-B5 Puriﬁer has been designed to improve indoor air quality by removing harmful particles for clean air and comfortable living experience.
This appliance is intended for indoor household use only.
Thank you for choosing BLACK+DECKER. We hope that you will enjoy using this product for many years.
For indoor domestic household use only.

This appliance is not to be used in:

Staff kitchen areas in shops, ofﬁces and other working environments;
Farm Houses;
By clients in hotels, motels and other residential type environments;
Bed and breakfast type environments or any other non household type environments.

Safety instructions

Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, ﬁre and/or serious injury.

Always route the power supply cord carefully to avoid a tripping hazard.
The intended use is described in this manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.
Warning! UV radiation is dangerous for the eyes and skin. Do not operate the UV-C emitter outside the appliance. Read the manual before replacing UV-C emitter.
The appliance must be disconnected from the supply before replacing the UV-C emitter
Precautions to be taken when replacing UV-C emitters and starters, if applicable
Unintended use of the appliance or damage to the housing may result in the escape of dangerous UV-C radiation. UV-C radiation may, even in little doses, cause harm to the eyes and skin.

Warning! When using mains-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of ﬁre, electric shock and personal injury and material damage.

Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

Retain this manual for future reference.

Electrical safety

Before use, check that the mains voltage corresponds to the voltage on the rating plate.
This appliance is double insulated therefore no earth wire is required.
To avoid the risk of electric shock, do not immerse the cord, plug or appliance in water or other liquid.
Check that the supply voltage shown on the rating plate of the appliance matches that of your electrical system. Any connection error will invalidate the guarantee.

Using your appliance

The temperature of accessible surfaces may be high when the appliance is operating and for some time afterwards.
Read all of this manual carefully before using the appliance.
Always take care when using the appliance.
Never pull the power supply cord to disconnect the plug from the socket.
Please don’t put any objects on top of puriﬁer. It will cause obstruction to outlet fresh air and may lead to decreased performance.
Keep the power supply cord away from heat, oil and sharp edges.
Do not put small objects on top of puriﬁer. It may get dropped into the unit through top vents and may cause damage to the internal part when unit is running.
Do not place the appliance on or near heat sources or in a heated oven.
Do not use the appliance outdoors.
If the power supply cord is damaged during use, disconnect the appliance from the power supply immediately. Do not touch the power supply cord before disconnecting from the power supply.
Disconnect the appliance from the power supply when not in use, before ﬁtting or removing parts and before cleaning.
Never let the appliance operate unattended.
Unit must be attended in use.
Do not let the cord hang over the edge of a table, counter, or touch hot surfaces.
Fully uncoil then guide the power supply cord neatly so it cannot be caught accidentally or tripped over.
The puriﬁer must not be located immediately below a socket-outlet.
To prevent overload and blown fuses, do not plug other appliance into same outlet (receptacle)
Do not place the puriﬁer on carpets, don’t place the cable under carpets. Arrange cord away from track areas so that it will not be tripped over.
Do not use this appliance under direct sunlight or near any heating object.
DO NOT place the puriﬁer under an electrical socket outlet or other product that maybe affected by humidity.
NEVER use this puriﬁer where it may come into contact with water i.e. bathroom, shower room, kitchen. Do not use this puriﬁer in the immediate surroundings of a bath, a shower or a swimming pool.
Warning! In order to avoid overheating, do not cover the puriﬁer.
Always ensure that hands are dry before operating or adjusting any switch on the product or touching the plug and mains supply connections.
To prevent a possible ﬁre, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
Don’ t use extension cable.
Always operate on a ﬂat horizontal surface.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, ﬁre or damage to the appliance.
Do not operate in areas where gasoline, paint or other ﬂammable liquids are used or stored.
The most common cause of overheating is deposits of dust or ﬂuff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and grilles.
Always use the puriﬁer in an upright position.
To disconnect the appliance, switch it “OFF” then remove.

Safety of others

Some parts of the product are small in size and may cause a choking hazards if swallowed by children or any individuals who have a tendency to place inedible objects in their mouths.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not allow children or any person unfamiliar with these instructions to use the appliance.
Do not allow children or animals to come near the work area or to touch the appliance or power supply cord.
Close supervision is necessary when the appliance is used near children.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance

After use

Remove the plug from the socket before leaving the appliance unattended and before changing, cleaning or inspecting any parts of the appliance.
When not in use, the appliance should be stored in a dry place. Children should not have access to stored appliances.

Inspection and repairs

Switch off the appliance before cleaning, changing accessories or approaching parts which move in use.
Before use, check the appliance for damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation.
Do not use the appliance if any part is damaged or defective.
Have any damaged or defective parts repaired or replaced by an authorised repair agent.
Before use, check the power supply cord for signs of damage, ageing and wear.
Do not use the appliance if the power supply cord or mains plug is damaged or defective.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualiﬁed person in order to avoid a hazard. Do not attempt to repair it yourself.
Never attempt to remove or replace any parts other than those speciﬁed in this manual.

Features

Control panel
- a. Pre-Filter
- b. HEPA reset
- c. Ionizer
- d. UV
- e. Night light
- f. Sleep / Lock
- g. Timer
- h. Speed / Auto
- i. On / Off
Display
- j) Night light mode
- k) Pre-filter reset
- l) HEPA Filter reset reminder
- m) Auto mode
- n) Fan speed
Light ring ( Red, Purple, Blue)
Filtered air outlet
Rear Sensor
HEPA filter
Rear Cover
Air Inlet

Pre-Operating instructions

Carefully unpack your air purifier.
Select a firm level place where there are no obstructions to the air inlet or filtered air outlet.
Press the tab of filter cover, and then pull the filter cover backwards to remove it.
Detach the HEPA filter and then unpack the PE bag carefully.
Replace the HEPA filter back in position, make sure that the primarily-efficient filter shall be pointed outwards.
Replace the filter cover back in position.

Operating instructions

Important:

Remove all PE bags from filters before use.
Always place the unit in an area such that there is enough clear space around the unit to avoid blocking of air suction .
Avoid blocking filtered area outlet (top grill) to facilitate purified air circulation in the room.

To operate your air purifier:

Plug into a electrical outlet of 220V~240/50~60Hz, two beeps “Bi-Bi” can be heard.
Press down the ON/OFF button, one beep “Bi” can be heard and its corresponding LED turns on, the light ring will illuminate in different color according to the current air quality and the display will show the value of PM2.5.
The air purifier starts to run under the default speed (AUTO setting). If you want to select other settings, you can press “ SPEED/AUTO” button to select your desired speed setting. There are five speed settings including Speed 1, Speed 2, Speed 3, Speed 4 and AUTO for selection. After select, its corresponding LED will turn on.
You can activate the timer after turn on the air purifier and select your required speed setting by following the operation as below: press down “TIMER” button on the control panel, one beep “Bi” can be heard. There are 4 settings including 2H, 4H, 6H and 8H for selection. After select your required timing, its corresponding LED turns on. When the timer expires, the air purifier will power off automatically and the LED will extinguish.
To activate the “Sleep” mode, press the “SLEEP/LOCK” button once to make the appliance enter into the “Sleep” mode, and then the corresponding icon of “Sleep” mode shown in the display illuminates.
To activate the “Child lock” function, hold and press the “SLEEP/LOCK” button for 3 seconds to make the appliance enter into the locking condition, and then the
corresponding icon of “Child lock” shown in the display illuminates.
To make the appliance enter into “Night light” mode, press the “NIGHT LIGHT” button once , and then the display and the light ring turn off and the middle part of the display shows “-”.
To release negative ions into the filtered air, press the “IONIZER” button once, then the negative ions will be released into outgoing filtered air to help the air purification process, and the icon of ionizer shown in the display will illuminate.
To activate the “UV lamp” function to sterilize, press the “UV” button on the control panel to turn on the UV lamp and the icon of “UV” shown in the display will illuminate.The icon of “UV” shown in the display will illuminate in blue solidly to remind the user to eplace the UV lamp if the appliance has been operated for up to 7300 hours cumulatively.
If you want to make the air purifier stop running, just need to press “ ON/OFF” button once. And the air purifier will stop working after hearing one beep “Bi”.

Mains plug replacement

If a new mains plug needs to be fitted:

Safely dispose of the old plug.
Connect the brown lead to the live terminal of the new plug.
Connect the blue lead to the neutral terminal.
If the product is class l (earthed), connect the green / yellow lead to the earth terminal.
Warning! If your product is class ll double insulated (only 2 wires in the cord set), no connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Any replacement fuse must be of the same rating as the original fuse supplied with the product

Cleaning and maintenance

Turn the air purifier off and unplug it before cleaning.
The outside of the air purifier can be cleaned with a soft, clean and dampened cloth.
The filtered air outlet and the filter cover can be cleaned of dust with a small, soft brush.
If you wish to clean the inside of the air purifier, please only use a dry, soft cloth to wipe it down.
Do not wash the HEPA filter.

WARNING: Do not allow moisture to come in contact with the main body of the air purifier.

Filter replacement instructions

On average, HEPA filter needs to be cleaned every 360 hours and replaced every 2160 hours. Filter life will vary depending on air quality and usage.
Turn off and unplug the air purifier before attempting to replace the filter.
Press the tab of filter cover to open the cover and then remove the HEPA filter.
Discard the old HEPA filter and do not attempt to clean. And then install a new HEPA filter well in position, make sure that the primarily efficient filter shall be pointed outwards.
Replace the filter cover back in position.

WARNING:

To clean the dust sensor carefully open the cover on the rear side of the unit.
Use dry cloth or cotton swab to carefully wipe the sensor.
Do not apply pressure while cleaning to avoid damage to the sensor.

Troubleshooting

Device does not work.

| Check if the device is plugged to the power supply.
Check if the device is turned on.

No or decreased air ﬂow

| Check if ﬁlter is properly installed and the ﬁlter cover is ﬁrmly closed.
Check the ﬁlter status and clean or replace if necessary (too dirty).
Check to ensure nothing is blocking the air inlet and ﬁltered air outlet.
Replace the HEPA ﬁlter if it has not been replaced periodically.
Ensure the plastic bag has been removed from the ﬁlter.
Error code interpretation

E11| This appliance is out of speed or under over heating protection. After 10mins, re-plug in the appliance and turn on it again.
E1| The motor is faulty, please contact the authorized service center or partner for checking

and repairs.

E5| The ﬁlter cover is not assembled properly, please re-assemble, then the appliance will

return to operation mode.

E0| The ﬁlter is not assembled properly, please re-assemble, then the appliance will return to

operation mode.

E2| The dust sensor or related circuit may be damaged, please contact the authorized service center or partner for checking and repairs.

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.
Should you find one day that your BLACK+DECKER product needs replacement, or if it is of no further use to you, do not dispose of it with other household waste. Make this product available for separate collection.
BLACK+DECKER provides a facility for recycling BLACK+DECKER products once they have reached the end of their working life. This service is provided free of charge. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by contacting your local BLACK+DECKER office at the address indicated in this manual.
Alternatively, a list of authorized BLACK+DECKER repair agents and full details of our after-sales service and contact are available on: www.2helpU.com

Technical Data

AP3560-B5

Input voltage| 220 – 240 V
Power input| 55 W
Frequency| 50-60 Hz

Warranty

BLACK+DECKER is confident of the quality of its products and offers an outstanding warranty.
This warranty statement is in addition to and in no way prejudices your statutory rights.
If a BLACK+DECKER product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, BLACK+DECKER warranty to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless:
The product has been used for trade, professional or hire purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign objects, substances or accidents;
Repairs have been attempted by persons other than authorised repair agents or BLACK+DECKER service staff.
To claim on the warranty, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local BLACK+DECKER office at the address indicated in this manual.
Alternatively, a list of authorised BLACK+DECKER repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.

BLACK AND DECKER (OVERSEAS) GMBH (DUBAI BRANCH) PO Box 17164, Dubai, United Arab Emirates BLACK+DECKER CUSTOMER SUPPORT