ZEVNI VRQAA3H961C5N8 Black Gold Chandelier Instruction Manual

June 17, 2024
ZEVNI

ZEVNI-LOGO

ZEVNI VRQAA3H961C5N8 Black Gold Chandelier

Product Specifications

  • Item Number : VRQAA3H961C5N8
  • Voltage: 120V
  • Max Wattage : Type B, Max 40W per bulb

Product Usage Instructions

Installation Warnings:

  1. We suggest installation by a licensed electrician.
  2. Read the instructions carefully and save them for future reference.
  3. Never attempt any work without shutting off the electricity until the work is completed.
  4. Ensure the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides.
  5. Check that the ceiling or wall can support the weight of the lamp before installation.
  6. Avoid exposing the lamp to acidic and alkaline substances to prevent surface damage.
  7. When replacing bulbs, turn off or unplug the lamp and allow it to cool down.

Cleaning Instructions:
To clean the fixture, use a soft cloth. For glass cleaning, use a mild cleaner such as mild and nonabrasive soap. Avoid abrasive materials like scouring pads, steel wool, or abrasive paper.

Assembly & Installation:

  1. Check all parts and accessories are included as per the illustration provided.
  2. Turn off power before starting the installation.
  3. Follow the provided instructions to assemble the fixture components in the correct order.
  4. Connect wires following the provided wire connection chart. Ensure proper grounding.
  5. Tighten all threaded pipes securely and check for snug connections.
  6. After connecting wires, wrap each connector with approved electrical tape and securely tuck all wires into the outlet box.

Frequently Asked Questions (FAQ)

  • Where can I order replacement parts for the fixture?
    All parts for this fixture can be ordered from the place of purchase. Make sure to use the exact wording from the illustration when ordering parts.

  • What tools are required for assembly and installation?
    Tools required but not included are as follows: Mounting plate, Green ground screw, Canopy, Swivel joint, Knob nut, Tube, Stem, Glass shade, Socket, Arms assembly. Additionally, you will need Plastic wire connectors and Mounting screws.

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.

  2. Please read the instruction carefully and save it as you may need it at a later time.

  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
      Place the main power switch in the “OFF” position.

    • Place the wall switch in the “OFF” position.

  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

  6. Make sure the voltage you are using is 120V. The maximum wattage is Type B,Max 40W per bulb.

  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non­abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

ZEVNI-VRQAA3H961C5N8-Black-Gold-Chandelier-FIG-2

PARTS LIST

ZEVNI-VRQAA3H961C5N8-Black-Gold-Chandelier-FIG-3

PARTS TYPE & QTY INCLUDING:

  • (C) Mounting plate (1)
  • (D) Green ground screw (1)
  • (E) Canopy (1)
  • (F) Swivel joint (1)
  • (G) Knob nut (2)
  • (H) Tube
  • (I) Stem (1)
  • (J) Glass shade (5)
  • (K) Socket (5)
  • (L) Arms assembly (1)

ACCESSORIES & QTY ENCLOSED:

  • (A) Plastic wire connector (3)
  • (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
      Place the main power switch in the “OFF” position.

    • Place the wall switch in the “OFF” position.

  3. Unscrew knob nuts (G) from canopy (E) then remove mounting plate (C).

  4. According to your desired hanging height to choose and use tubes (H).
    Then pass the fixture wires through stem (I), the chosen tubes (H), swivel joint (F) and canopy (E).
    Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) and stem (I) together onto swivel joint (F) and the top of arms assembly (L). Hand tighten till snug.

  5. Attach mounting plate (C) to the outlet box with mounting screws (B).

  6. Make wire connections
    Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

ZEVNI-VRQAA3H961C5N8-Black-Gold-Chandelier-FIG-7
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  1. Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre­assembled screws in mounting plate (C).
    Note: canopy (E) should be snug against the ceiling and knob nuts (G).
    If not, adjust the threaded length on mounting plate assembly (C):

    • first, unscrew the pre­assembled hex nuts;
    • then, screw the pre­assembled screws in or out of mounting plate (C);
    • when the secure length is achieved, tighten the hex nuts and back to step 7.
  2. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
    Carefully screw glass shades (J) onto sockets (K).

  3. Check everything is already installed properly, then you could turn on the light. Enjoy!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ZEVNI User Manuals

Related Manuals