Texas A S EC 2600 Lawn Edger Lawn Edger User Manual

June 17, 2024
Texas A S

User Manual
EC 2600
Texas A S EC 2600 Lawn Edger Lawn Edger - Cover
Version 24.1
Texas A/S – Knullen 22 – DK-5260 Odense S – Denmark
Tel. +45 6395 5555 – www.texas.dkpost@texas.dk

EC 2600 Lawn Edger Lawn Edger

VIGTIGT!
FØR MOTOREN STARTES, SKAL BOLTEN/VINGEMØTRIKKEN VÆRE MONTERET I ET AF DE 3 HULLER MIDT PÅ HÅNDTAGET.
HOLD FØDDER OG HÆNDER VÆK FRA KNIVEN. ALTID START MOTOREN FRA MODSATTE SIDE AF KNIVEN.
IMPORTANT!
BEFORE THE ENGINE IS STARTED, MAKE SURE THE SCREW/KNOP IS FITTED INTO ONE OF THE 3 HOLES IN THE MIDDLE OF THE HANDLE.
KEEP FEET AND HANDS AWAY FROM THE BLADE. ALWAYS START ENGINE FROM OPPOSITE SIDE OF BLADE.

Spare parts
Part list and drawings for the specific product, can be found on our website www.texas.dk
If you help find part numbers yourself, it will ease the service.
Spare parts can be purchased online at www.texas.dk, or at your local dealer.

Safety instructions

  • Read this manual carefully before using the machine so that you understand and are able to fully comply with all safety instructions and ways of operation.

  • Children may not use the machine.

  • If you feel sick, tired, or have been drinking alcohol or taken medicine you may not use the machine.

  • Always use eye- and ear protection and solid footwear when using the machine.
    Avoid loose fitting clothes.

  • Make sure to have good foot hold and have good control of the machine when using it.

  • Make sure that spectators are placed at least 10 m from where you start or use the machine.

  • Do not use the machine near explosive fluids, gasses or dust. The machine may make sparks that can ignite dust etc.

  • Never start using the machine until the work area has been cleared. Make sure to have enough light.

  • Use the machine with the blade turning away from persons and windows.

  • Only tank fuel when the engine is turned off and in well ventilated surroundings.
    Any spilled fuel must be wiped off.

  • Any repairs except those that are described in this manual must be carried out by an authorized dealer. The machine must be turned off when repairs are carried out.

  • Only use original spare parts for repair.

  • The machine must only be lent to persons who are familiar with the use.

  • This manual should always follow the machine.

Identification

Texas A S EC 2600 Lawn Edger Lawn Edger - Identification
1

1. Handle 2. Throttle
3. ON/OFF 4. Handle
5. Shaft 6. Adjustment edger
7. Wheel 8. Handle knob
9. Adjustment of cutting height 10. Front wheel
11. Blade cut indicator 12. Tank
13. Recoil 14. Primer
15. Spark plug 16. Air filter cover
17. Choke 18. Length adjustment of shaft
19. Lock for air filter

Assembly of the machine

|
---|---

Before inserting the adjustable height shaft into the edger, make sure it is fully extended.
Carefully guide the bottom of the extended shaft into the base of the edger, taking care not to kink or catch the operating cable.
Lining up the holes in the shaft with the location holes in the base of the edger.
Insert the bolt through the base and secure it tight.
Check the throttle is operating correctly before you start the edger.
Mount the handle (press it down) and tighten it.
You can adjust it in the position/angle that suits you best.

Gasoline and oil.

|
---|---

Use unleaded gasoline octane 95.
Use 2-stroke oil. Mix gasoline and oil 50:1 (2%), if you use Tex-Parts 2-stroke oil (spare part no. 90306480). All other types of 2-stroke oil should be mixed 40:1 (2,5%). Use a container designed for the purpose. Never mix directly into the tank.
Never tank with the engine running or when it is hot.
If you spill fuel it must be wiped off before starting the engine.
Move the machine away from where you tanked before starting it.

Start / stop

Texas A S EC 2600 Lawn Edger Lawn Edger - Start stop 1

Press the ON/OFF switch to I.
ON = I, OFF = 0
Press the primer 6 times until no more air is seen in the return pipe. (This is not necessary if the engine is warm).

Texas A S EC 2600 Lawn Edger Lawn Edger - Start stop 2

Activate the choke. (This is not necessary if the engine is warm).

Texas A S EC 2600 Lawn Edger Lawn Edger - Start stop 3

Pull the recoil cord until the engine starts. Press down the choke handle to open position.
It is important to follow the recoil cord back with your hand and not let it jump back by it self.
Leave the engine to run for 10 seconds before using the machine.
Adjust the speed using the throttle.

Texas A S EC 2600 Lawn Edger Lawn Edger - Start stop 4

The engine is turned OFF by pressing the ON/OFF switch to 0.
Important. Do not use the machine at very high rotations (throttle) for the first 10 hours. All bolts and nuts must be tightened after 2 hours use.

Adjustment of cutting height

The cutting height has 3 positions: 10, 20, and 30 mm.
To adjust the height turn the adjustment knob 5-6 full turns.
It should not be removed.

Texas A S EC 2600 Lawn Edger Lawn Edger - Adjustment of cutting height
2

Press the knob towards the machine and at the same time move the front wheel to the other side. Lift or lower the arm to the new position.
Pull the knob back out and tighten when the arm is in the correct position.

Edge guide

The edge guide is used when working against solid material like a paved surface to prevent the blade from being damaged against the hard surface.
Press the handle to the side (towards the centre of the machine) and then downwards. Then press it to the side again.
The edge guide is now active.

When the edge guide lever is up the edge guide is not in use.

Using the machine

Check the area for wiring, rock and other parts that may be damaged or make damage to the machine.
Adjust the cutting height to 20 mm. If the ground is very hard or very soft you may need to change the adjustment to 10 mm and 30 mm.
Use the edge guide to keep the direction.
Slowly lower the edge cutter while pressing the throttle.

Slowly push the machine forward keeping the direction.
If cutting against a paved surface use the edge cutter by pressing it lightly against the paved surface. See above how to active the edge cutter.

Changing the blade

Texas A S EC 2600 Lawn Edger Lawn Edger - Changing the blade
1

Place the edge cutter on the side with the blade turned up. Make sure the machine is placed on a clean surface to prevent dirt from getting into the air intake of the engine.
Remove the spark plug cap.
Hold firmly a spanner on the blade flange loosen the lock nut with another spanner.

Texas A S EC 2600 Lawn Edger Lawn Edger - Changing the blade
2

Remove the blade.

Fit a new blade.

Fit the disc and the nut and tighten.

Air filter

Texas A S EC 2600 Lawn Edger Lawn Edger - Air filter 1

The air filter should be cleaned regularly according to the area in which you use the machine.
Remove the cover. Large dust particles may be removed by tapping the filter lightly.
Wash the filter in mild soapy water. Rinse thoroughly and let it dry completely. Pour a few drops of 2-stroke oil onto the filter.
Press the filter to remove any excess oil. Remount the filter.
Fit the cover correctly and lock it.

Spark plug

Check the spark plug after 10-15 hours of use.
Remove the spark plug cap. Use the spark plug wrench to remove the spark plug.
Clean the spark plug and adjust the spark plug gap to 0.6 – 0.7 mm.
Replace damaged or worn spark plugs.

Fit the spark plug with your fingers. Fasten tightly using the wrench.
Use spark plugs type Denso W14M-U10.

Maintenance and storage

Every time the machine has been used it should be cleaned completely.
If the machine will not be used for a longer period of time the fuel tank must be emptied completely. All metal parts must be oiled to prevent corrosion.
Remove the spark plug, pour a few drops of engine oil into the cylinder and pull the starting cord 2-3 times to make the oil disperse. Fit the spark plug.

Only use original spare parts.

Trouble shooting

Problem Cause Solution
Lack of power or sudden stop to the engine Lack of gasoline Tank
The fuel does not reach the carburettor Clean the fuel filter in the tank
Water in the fuel Clean the fuel system and tank fresh oil-mixed fuel
Air filter is dirty Clean air filter
Bad quality cutting Dirt on the blade Clean the blade
Blade is worn Replace

Specifications

Model Edge cutter EC2600
Engine 26 cc, 2-stroke
Revolutions 0 – 2200 / min
Volume of tank 700 ml
Size of knife 180 mm
Weight 7,0 kg
Cutting height 10-30 mm
Fuel Unleaded octane 95 mixed 40:1
Spark plug Denso W14M-U10

Accessory

A weed cleaner brush can be fitted on the edge cutter, to clean between the tiles.
The weed cleaner brush is sold separately.
It can be purchased at your local dealer or at www.texas.dk.
Article number: 90062054

The plate, shown to the right, is included with the machine.
It is only used for fitting the brush on the machine.

EC Certificate of conformity

Manufacturer  Texas Andreas Petersen A/S
Hereby certifies that the following  Lawn edger gasoline EC 2600
Is in compliance with the specifications of the machine directive and subsequent modifications 2006/42/EC
Conforms with the following standards
ISO 11789 : 1999, EN ISO 12100:2010, AfPS GS 2014:01
Measured LpA: 93.7 dB(A)
Guaranteed LwA: 119 dB(A)
Vibrations (hand):
ah = 10.2 m/s 2
Serial numbers: 2401590001 – 2601599999
EU 5 emission no.: e242016/16282018/989SHA1/P016600

Texas Andreas Petersen A/S
Knullen 22 • DK-5260 Odense S
26.09.2023

Johnny Lolk
Managing Director

Responsible for documentation
Johnny Lolk

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals