COSTWAY UY10052 Football Table User Guide

COSTWAY UY10052 Football Table

• office: Fontana

If you’re having difficulty, our friendly customer team is always here to help.

• USA: cs.us@costway.com

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Before You Start

• Please read all instructions carefully and keep it for future reference.

General Security Warning

• Caution: Children should use this product under parental supervision.
• Danger: Keep all small parts and packaging materials for this product away from babies and children, otherwise they may pose a choking hazard.
• Danger: Lack of attachment may cause a risk of tipping.

WARNING: CHOKING HAZARD

• Small parts.
• Not for children under 3 years.

Warning for Assembly

• Assembled only by adults
• Remove all packaging, separate and count all parts and hardware.
• Read through each step carefully and follow the proper order.
• We recommend that, where possible, all items are assembled near the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
• Ensure a secure surface during installation, and always place the product on a flat, steady and stable surface.

PARTS

1. Open the carton near where you plan to place the table. Select a clean and level floor. At least two adults are required for assembly.

2. Remove all the contents inside the carton and verify that you have all listed parts as shown on the Parts List.
   NOTE: The player rods are pre-assembled.We suggest that you use the bottom carton as a clean flat working area to protect the game. Carefully cut or tear the four carton comers so that the bottom can be used as your work area.

3. Attach one End Apron (#2) between Side Aprons (# 1). Secure with one Leg Bolt (# 12) and one Washer (# 13) per side apron, and screw them through Side Aprons into End Apron. NOTE: Do not tighten screws securely at this time. Leave the screws slightly loose.

4. Locate Playfield ( # 3 ) and slide the playfield with graphics facing down as shown in FIG. 1 . If the field does not slide smoothly, ensure you have not over-tightened any screws, or the playfield is not caught by the slot.

5. Repeat the step to attach the other End Apron (#2) to the Side Aprons(# 1).Center the playfield between the two end aprons,and make sure that the playfield is in the grooves of the side aprons and end aprons.
   NOTE: Be sure that two side aprons and end aprons are in line. Now go back and tighten all the connections.

6. Place the Support Brace ( # 4 ) on the Playfield ( # 3 ) as shown in FIG. 2. Attach it using two of Washer Head Screws ( #14 ).

7. Attach the Left (#5) and Right (#6) Legs to the cabinet using three of the Leg Bolts (# 12) and three of Washers (# 13)per leg. See.FIG.3.

8. Lift the table, turn it over, and set the table on its legs in the location where you will play. This should be done by at least two adults. Go back and make sure that all connections are tight.

9. Attach the End Leg Brace ( # 7 ) to the legs ( # 5 # 6 ) using four Screws ( # 11 ) per Leg Brace.

CAUTION

Two adults are recommended to flip the table as shown.

1. Grab the table on the ground.

2. Turn the table over.

3. Place it on all four feet at the same time on the ground.

4. HOLD TABLE

5. CABINET

6. DO NOT HOLD THE LEGS

7. DO NOT LEAN THE TABLE

1. Attach the player rods (#8) into the side aprons as shown in Fig.4-1 Attach the rubber bumper (#20) to the player rod, followed by the players (#9 & # 10) and another rubber bumper (# 20).For the two goalie player rods an additional stop ring (# 19) will be needed to be added between the goalie.

2. Attach Stop Rings (# 19) and Players (#9 & # 10) to the player rods using Round Head Screws (# 15) as shown in Fig.4-2.

3. Put the Hand Grips ( 17 ) and End Caps ( 18 ) on the player rods in order as shown in FIG. 5 .
   NOTE: To make the handles easier to attach, spray a little window cleaner/lubricant on the rod ends prior to installation and tap on the players gently with a hammer once in place. See FIG. 5

4. Insert Scorer ( # 23 ) on each end apron as shown in FIG 5.

Return / Damage Claim Instructions

DO NOT discard the box / original packaging.
In case a return is required, the item must be returned in original box. Without this your return will not be accepted.

Take a photo of the box markings.
A photo of the markings (text) on the side of the box is required in case a part is needed for replacement. This helps our staff identify your product number to ensure you receive the correct parts.

Take a photo of the damaged part (if applicable).
A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged.

Send us an email with the images requested.
Email us directly from marketplace where your item was purchased with the attached images and a description of your claim.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>