BOTEX WDMX Battery TRX IP Intended for The Wireless Transmission User Guide
- June 17, 2024
- BOTEX
Table of Contents
BOTEX WDMX Battery TRX IP Intended for The Wireless
Specifications
- Product Name: WDMX Battery TX IP
- Intended Use: Wireless transmission of DMX signals in lighting systems
- Operating Location: Indoors
- Frequency Range: EU-approved
- Control LEDs: Battery, Signal Strength, Control LEDs
Safety Instructions:
Ensure to follow the safety instructions provided in the manual to prevent
personal injury or property damage.
Electric Shock Prevention:
Avoid removing covers or modifying the device. Always use properly insulated
mains cable to prevent electric shock.
Electromagnetic Compatibility
Avoid using the device near radios or TV sets to prevent interference.
Maintain distance between devices to avoid signal disruption.
Quick start guide
This quick start guide contains important information on the safe use of the
product.
Read and follow the safety instructions and all other instructions. Retain the
quick start guide for future reference. If you pass the product on to others,
please include this quick start guide.
Safety instructions
Intended use
This device is intended for the wireless transmission of DMX signals in
lighting systems. Any other use or use under other operating conditions is
considered to be improper and may result in personal injury or property
damage. No liability will be assumed for damage resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not in the reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow small parts and choke. Never let children play unattended with the electrical devices.
Electric shock caused by high voltages inside
The device contains parts where high voltage is present. Never remove any
covers. There are no user-serviceable parts inside the device. Do not use the
device if covers, safety equipment or optical components are missing or
damaged.
Electric shock caused by short circuit
Always use a properly insulated, tripe-core mains cable. Do not modify the
mains cable. Failure to comply may result in electric shock and risk of fire
and loss of life. If in doubt, seek advice from a registered electrician.
Electromagnetic compatibility with other electrical equipment
Using the device near radios or TV sets may cause interference. In that case,
increase the distance between the devices.
Notes on radio transmission
This equipment uses a frequency range that is free of charge and registration
within the European Union (EU). For more information, please visit:
http://www.thomann.de. Make sure that no metal objects are located between the
transmitter and receiver. Avoid interference caused by other radio systems.
Possible staining
The plasticizer contained in the rubber feet of this product may react with
the coating of the floor and cause permanent dark stains after some time. If
in doubt, avoid direct contact between the rubber feet and the floor by using
a suitable mat, such as felt slides or similar.
Operating location
Never use the product in the following ambient conditions:
- in direct sunlight
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty places
- in the immediate vicinity of a heat source or near open flames
- in places with high electrostatic or magnetic radiation
General handling
- To prevent damage, do not exert force when handling the product.
- Do not immerse the product in water. Only ever wipe it down with a clean dry or damp cloth. Donot use liquid cleaners such as benzene, thinners or flammable cleaning agents
- Disconnect the device from the power supply when it is not in use.
Features
- Battery-powered outdoor WDMX transceiver / wireless solution WDMX module
- Suitable for outdoor use
- Can be configured as a transmitter and receiver
- Flexible assembly on truss with M10 thread, omega bracket and velcro
- Latency-free wireless transmission of DMX signals up to 700 m
- High reliability
- Easy and simple operation
- Power supply: Seetronic TR1
- DMX input/output: Seetronic 3-pin XLR
- RDM
- Battery life: 80 hours as a transmitter, up to 440 hours as a receiver
- IP65
Connections and controls
-
[SIGNAL] control LED
Lights up when a connection has been established. -
[BATTERY] control LED
Lights up green: The battery is fully charged.
Lights up red: The battery is charging. -
[SIGNAL STRENGTH] control LEDs
Depending on whether the device is running as a transmitter or receiver: Transmitter: Indicates the set transmission power.
Receiver: Indicates the quality of the received signal. -
% Control LED
-
[TX]: Device is running as a transmitter. [RX]: Device is running as a receiver. [LINK]: Device is running as a transmitter: Lights up: Device is ready to establish a connection.
-
Device is running as a receiver:
-
Off: Device is not connected to a receiver.
-
Lights up: Device is connected to a receiver.
-
Flashing: Device is paired with a receiv-er, but there is no connection.
[DATA]: -
Off: None data transfer.
-
Lights up green: DMX data in use. Lights up red: RDM data are in use.
-
[MODE]: Indicates the radio mode.
-
[PWR]: Lights up when the device is on.
-
[RDM]: Flashes when RDM signals are being received.
-
-
Connect button
-
[POWER IN]: Power Twist power connection
-
( [DMX IN]: 3-pin XLR )
-
[DMX OUT]:3-pin XLR *
-
[SWITCH]: On/off switch
Connecting the device:
Only as transmitter:
- Briefly click the connect button.
The [LINK] LED flashes:
The device is connecting to all receivers that are ready for connection.
Breaking the connection
- Press the connect button for 3 seconds.
Switching the device between receiver (TRX) and transmitter (TX):
- Briefly click the connect button 5 times.
- Press the connect button for 3 seconds.
- Press the connect button to switch between RX and TX. The selection is indicated by flashing of the relevant LED.
- Press and hold the connect button to confirm the selection.
Technical specifications
- Input connections Power supply Seetronic Power Twist TR1
- DMX control 1 × Seetronic 3-pin XLR
- Output connections DMX control 1 × Seetronic 3-pin XLR
- Frequency bands 2.4 GHz, 5.2 & 5.8 GHz
- W-DMX Range (outdoors) max. 700 m, without obstacles
- Power consumption max. 450 mW
- Supply voltage AC:100 – 250 V ~ 50/60 Hz
- International Protection Rating IP65
- Installation properties Omega bracket with M10 thread
- Dimensions with antenna 185 mm × 170 mm × 59.6 mm (W × H × D)
- Weight 1.8 kg
- Ambient conditions Temperature range 0 °C…40 °C
Relative humidity 20% to 80% (non-condensing
Environmentally friendly materials have been chosen for the packaging. These materials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are disposed of in the proper manner. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the instructions and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) as amended. Do not dispose of your old device with your normal household waste. Dispose of the product through an approved waste disposal firm or through your local waste management facility. When disposing of the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste management facility.
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>