MARVEL MLKR224-ISA1A Panel Ready Beer Cooler Kegerator Owner’s Manual

MARVEL MLKR224-ISA1A Panel Ready Beer Cooler Kegerator

Product Information

Specifications

• Model: MLKR224-ISA1A
• Product Type: Undercounter Refrigeration
• Width: 24 inches (60 cm)
• Manufacturer: Marvel

Frequently Asked Questions

• Where can I find the serial number of the appliance?

  • The serial number can be found on the serial plate inside the cabinet on the left side near the top.
    

• How do I register my product warranty?

  • You can register your product warranty online at www.marvelrefrigeration.com. Make sure to have the serial number, date of purchase, and dealer’s name and address handy during registration.
    

• Can I use a custom grille instead of the factory-provided one?

  • No, it is important to use the factory-provided grille to maintain proper air flow through the condenser. Using a custom grille will void the warranty.
    

• How can I share photos of my Marvel product with Marvel Refrigeration?

  • You can send photos of your installed product to marketing@marvelrefrigeration.com. Your design might be featured on their website and social media.

Welcome to the Marvel Experience!

Thank you for choosing our quality American-built product to add to your home. We are thrilled to welcome you to our growing community of Marvel owners, who trust in our products and our support. The information in this guide is intended to help you install and maintain your new Marvel undercounter model to protect and prolong its lifetime. We encourage you to contact our Technical Support team at 616-754-5601 with any questions.

Got a Marvelous Design?

We would love to see how your Marvel product looks in its new home. You can send us photos of your installed product at marketing@marvelrefrigeration.com, and we might feature your Marvel home design on our website and social media!

Warranty Registration

It is important you register your product warranty after taking delivery of your appliance. You can register online at www.marvelrefrigeration.com.

The following information will be required when registering your appliance:

• Serial Number
• Date of Purchase
• Dealer’s name and address

The serial number can be found on the serial plate which is located inside the cabinet on the left side near the top.

Online registration available at: marvelrefrigeration.com

INTEGRATED PANEL DIMENSIONS

NOTE

• Panel thickness may be 5/8″ or 3/4″
• Center the unit in the 24″ opening
• If the hinge side of the product is pressed against the adjacent cabinet, use a 5/8″ thick panel
• The window cutout is for glass door models only
• Do not use a solid door panel on a glass door model

Door Type / Maximum Panel Weight

• Solid: 15 lbs
• Frame Glass: 10 lbs

INTEGRATED DOOR PANEL INSTALLATION

Cut and prepare panels according to the information provided in the Integrated Panel Dimensions section.

CAUTION

It is important to use the factory provided grille that came with the product to assure proper air flow is maintained through the condenser. The use of a custom grille is not recommended and will void the warranty.

Step 1: Removing the Door and Hinges

• Hold the door secure in the closed position and remove Hinge Pin from the Upper Hinge using a 1/8” Hex Key tool.
• Slowly remove the door by sliding outward away from the cabinet and lift to remove off the Lower Hinge. If reversing the door, remove hinges from cabinet per Door Reversal Instructions.
• Remove the hinge bushing from the adaptor plate. A new bushing is included in the literature pack with your unit.

Step 2: Remove the Door Gasket

• With the door laying on a flat surface and starting at a corner of the door, remove the magnetic door gasket from the interior side of the door. Set the gasket aside on a flat surface.
• There are 10 holes in the gasket retainer extrusions (3 on each side and 2 at the top and bottom) which are used to fasten the panel to the front of the door. The screws are provided in the literature pack.

Step 3: Assemble the Panel to the Door

The preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or “C” clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom panel should be flush with the top of the door and centered along the width of the door. Drill holes through the gasket extrusion using the 10 holes as pilot holes. Use the drill size from the chart in the table below being careful not to drill through the front surface of the panel. Fasten the panel to the door with the 10 screws provided in the literature pack. Remove the clamps and replace the gasket in the gasket extrusion channels of the door. Some force may be required to seat the gasket into the channels. Be sure the gasket corners are seated properly.

Step 4: Install the Door

• If reversing the door swing, reinstall hinges per Door Reversal Instructions.
• Carefully slide lower hinge bushing over bottom hinge pin. Install the new upper hinge bushing into adaptor plate.
• Align hinge bushing with top hinge and reinstall upper hinge pin using 1/8” Hex Key so that the pin is flush.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>