ZIP364IPVII Monogram 36 Premium Integrated French Door Refrigerator User Manual

ZIP364IPVII Monogram 36 Premium Integrated French Door Refrigerator

Product Specifications

• Model: French Door Custom Panel Templates
• Manufacturer: Monogram
• Template Dimensions: 8.5 x 11 inches (21.59 x 27.94 cm)
• Pilot Hole Size: 5/64 inch
• Maximum Pilot Hole Depth: 1/2 inch

Product Usage Instructions

Bracket A1 Installation:

1. Place the template on the panel back.
2. Align the top dashed line to the panel’s top edge.
3. Align the right dashed line to the panel’s right edge.
4. Drill two pilot holes as indicated on the template.
5. Remove the template and install bracket A1, centered on the screws without tightening them.
6. Drill a pilot hole in the center of the empty slot in the bracket and install the screw.

Bracket D1 Installation:

1. Follow the same steps as for Bracket A1, but align with the left dashed line instead of the right.

Bracket G1 Installation (Right):

1. Measure the distance from the panel’s top edge to the bottom edge and mark the panel center along the right edge.
2. Place the template on the panel back with the top edge towards the panel’s top edge.
3. Align the template centerline to the panel center and the right dashed line to the panel’s right edge.
4. Drill pilot holes as indicated on the template.
5. Install bracket G1 after mounting the panel to the door.

Bracket G1 Installation (Left):

1. Follow similar steps as for Bracket G1 (Right), but align with the left dashed line instead of the right.

Frequently Asked Questions

Q: Can I use a different paper size for printing the templates?

A: It is recommended to print the templates on 8.5 x 11 inches (21.59 x 27.94 cm) paper only to ensure accurate sizing.

Q: What should I do if the pilot holes exceed 1/2 inch in depth?

A: Ensure that the pilot holes are drilled to a maximum depth of 1/2 inch as exceeding this may affect installation stability.

Product Information And Installation

BRACKET A1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL TWO PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET, CENTERED ON SCREWS. DO NOT TIGHTEN SCREWS.
6. DRILL PILOT HOLE* IN CENTER OF EMPTY SLOT IN BRACKET AND INSTALL SCREW.

RIGHT

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
• NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

BRACKET D1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL TWO PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET, CENTERED ON SCREWS. DO NOT TIGHTEN SCREWS.
6. DRILL PILOT HOLE* IN CENTER OF EMPTY SLOT IN BRACKET AND INSTALL SCREW.

LEFT

• PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP

BRACKET G1 (RIGHT):

1. MEASURE DISTANCE FROM PANEL TOP EDGE TO PANEL BOTTOM EDGE AND MARK PANEL CENTER ALONG PANEL BACK RIGHT EDGE.

2. PLACE TEMPLATE ON PANEL BACK.

3. POINT TEMPLATE TOP EDGE TOWARDS PANEL TOP EDGE.

4. ALIGN TEMPLATE CENTERLINE TO PANEL CENTER.

5. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.

6. DRILL PILOT HOLES* IDENTIFIED BELOW.

7. REMOVE TEMPLATE.

8. INSTALL BRACKET AFTER MOUNTING PANEL TO DOOR

9. PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.

10. PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
    NO MARGINS OR HEADERS/FOOTERS.

11. VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES

RIGHT

BRACKET G1 (LEFT):

1. MEASURE DISTANCE FROM PANEL TOP EDGE TO PANEL BOTTOM EDGE AND MARK PANEL CENTER ALONG PANEL BACK LEFT EDGE.
2. PLACE TEMPLATE ON PANEL BACK.
3. POINT TEMPLATE TOP EDGE TOWARDS PANEL TOP EDGE.
4. ALIGN TEMPLATE CENTERLINE TO PANEL CENTER.
5. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
6. DRILL PILOT HOLES* IDENTIFIED BELOW.
7. REMOVE TEMPLATE.
8. INSTALL BRACKET AFTER MOUNTING PANEL TO DOOR

LEFT

BRACKET B1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

RIGHT

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT. NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES

BRACKET E1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS

LEFT

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT. NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.
• 4.5″ MINIMUM STILE WIDTH. 3″ MINIMUM RAIL WIDTH.
• FOR PANELS WITH 3″ STILES AND RAILS, AN EXTRA HOLE MUST BE DRILLED INTO THE J1 BRACKET IN THE REGION IDENTIFIED. AFTER PANELS ARE ADJUSTED, INSTALL A SCREW THROUGH THE DRILLED HOLE.

BOTTOM

RIGHT

BRACKET H1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE.
6. INSTALL BRACKET WITH SMALL WASHERS OVER BRACKET AFTER MOUNTING PANEL TO DOOR.

BRACKET J1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET WITH SMALL WASHERS OVER BRACKET. DO NOT TIGHTEN SCREWS

BRACKET H1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET WITH SMALL WASHERS OVER BRACKET. DO NOT TIGHTEN SCREWS.

BRACKET J1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5.  REMOVE TEMPLATE.
6. INSTALL BRACKET WITH SMALL WASHERS OVER BRACKET AFTER MOUNTING PANEL TO DOOR.

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT. NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.
• 4.5″ MINIMUM STILE WIDTH. 3″ MINIMUM RAIL WIDTH.
• FOR PANELS WITH 3″ STILES AND RAILS, AN EXTRA HOLE MUST BE DRILLED INTO THE H1 BRACKET IN THE REGION IDENTIFIED. AFTER PANELS ARE ADJUSTED, INSTALL A SCREW THROUGH THE DRILLED HOLE.

BRACKET C1:

1. PLACE TEMPLATE ON PANEL BACK.
2.  ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT. NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES

BRACKET F1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

BRACKET A1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT. NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES

BRACKET D1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

BRACKET B1:

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
3. ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
4. DRILL TWO PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET, CENTERED ON SCREWS. DO NOT TIGHTEN SCREWS.
6. DRILL PILOT HOLE* IN CENTER OF EMPTY SLOT IN BRACKET AND INSTALL SCREW

• PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
• PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT. NO MARGINS OR HEADERS/FOOTERS.
• VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

BRACKET E1:

LEFT

1. PLACE TEMPLATE ON PANEL BACK.
2. ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
3. ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
4. DRILL TWO PILOT HOLES* IDENTIFIED BELOW.
5. REMOVE TEMPLATE AND INSTALL BRACKET, CENTERED ON SCREWS. DO NOT TIGHTEN SCREWS.
6. DRILL PILOT HOLE* IN CENTER OF EMPTY SLOT IN BRACKET AND INSTALL SCREW.

References

• Monogram Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>