Velay Home EF36 In Wall Recessed Electric Fireplace Owner’s Manual
- June 17, 2024
- Velay Home
Table of Contents
In Wall Recessed Electric Fireplace
Owner’s Manual
Model Number:
EF36, EF42, EF50, EF60, EF72, EF84
120V AC; 60Hz; 1500Watts
EF36 In Wall Recessed Electric Fireplace
WARNING Read and understand this entire owner’s manual, including all
safety information, before plugging in or using this product. Failure to do so
could result in fire, electric shock, or serious personal injury.
CAUTION Keep this owner’s manual for future reference. If you sell or
give this product away, make sure this manual accompanies this product.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
- Read all instructions before using this appliance.
- This heater is hot when in use. To avoid burning, do not touch hot surface. If provided, use handles when moving this heater.
- Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 1 m from the front of the heater and keep them away from the sides and rear.
- Do not cover the heater to avoid overheating.
- Extreme caution is necessary when any heater is used near children or the infirm and whenever the heater is left operating and unattended.
- Always unplug heater when not in use.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner, return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
- Do not use outdoors
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tipped over.
- To disconnect heater, turn controls to off, then remove plug from outlet.
- Do not inset or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings many become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, or flammable liquids are used or stored.
- Use this heater only as describes in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- DANGER-HIGH Temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of this heater.
- Replacement of the lamps should be done only while the heater is disconnected from the supply circuit.
- Only use the appliance in accordance with the instructions in this manual! It cannot be used for any other purpose.
- Never operate the appliance when the appliance itself or the main cable show any signs of damage. In order to avoid overheating, do not cover the heater.
- Be responsible when handling the packing material. Warning: plastic wrapping may be lethal to children.
- Do not place the appliance next to a socket.
- Never operate the heater on a program switch, timer switch or any other appliance for automatic operation.
- Never use the heater in the bathroom, shower or near a swimming pool.
- The heater must not be located immediately below a socket-outlet
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- Components should only be serviced by an approved electric technician.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
INSTALLATION INFORMATION
WARNING: Find a safe location and build a suitable hole for fireplace.
Minimum clearance from the ceiling and the mantel must be at least 8
inches(200mm); Minimum clearance from the front must be at least 3
feet(900mm). Choose a location near an outlet so an extension cord is not
required.
Take model EF50 as an example. Prepare a wall with a framed opening of 45.7 inch(1160mm) wide X 21’’(533.4mm) high. Make sure the width of the wood block on both sides which used to fix the fireplace is 3’’(76mm). Make sure that the revealed wood block width on both sides is about 1 1/2’’(37.5mm) after finishing the plasterboard. Measure the depth D from the plasterboard surface to the wood block and write it down.
| MODEL | EF36 | EF42 | EF50 | EF60 | EF72 | EF84 |
|---|---|---|---|---|---|---|
| A | 31.7’’ | |||||
| (805mm) | 37.7’’ | |||||
| (957mm) | 45.7’’ | |||||
| (1160mm) | 55.7’’ | |||||
| (1414mm) | 67.7’’ | |||||
| (1720mm) | 79.7’’ |
(2025mm)
Before
installing the in-wall fireplace, please read the following steps carefully.
Remove the two silver colored screws at both sides of the fireplace (See Step
- Attention: no need the 2 silver colored screws when installing.
Lift glass panel
and pull it out upwards to you, leave screws out when installing in wall (See
Step 2) Removed the log from the bed if you want to change to the crystals,
please remove the carton protection pack inside the fireplace first. (See Step -
Kind attention: If you like the real log effect, please keep it on the bed and leave the crystals into a safe place for replacement in future. Put the optional fire crystals on the bed,please put the plastic strip on the bed first. (See Step 4) Warning This carton includes GLASS! ALWAYS use extreme caution when handing glass. Failure to do so could result in personal injury or property damage.
Warning ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating.
Failure to do so could result in electric shock, fire or personal injury.
Put the Fireplace box into the wall, there are two hanger brackets in both sides of the fireplace box, using 6 pcs of ST4XX40 screws (each side with 3 screws) to lock the fireplace in the wooden wall.
Using the Philips Screw Driver”+” to
fix the six screws on the wall between two sides Figure (A)). Make sure the
front of the firebox is not lower than the surface of the wall.
**** The next step requires installation of a Glass panel! The manufacturer recommends that two adults install, the glass panel. Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage, please see the Figure (B).
Carefully set both hooks of the front glass panel onto the firebox. Note: Make sure the glass fully attached to the firebox so that the control panel can work properly. This will keep the decorative glass in place and enable the control panel work well. 
OPERATION INSTRUCTION
【To switch on】
Plug in the appliance into the socket. Turn on the Power Switch
The control Switch Panel is on the bottom of tempered glass panel (See
pic)
【Instruction for Remote Controller and Switch Panel】
Control Panel / Remote Control Operation
The touch display panel is shown by LED’s on the front bottom right of the appliance. The LED’s will appear on the bottom of the fireplace control panel.
| POWER | Turns the appliance ON/OFF. | |
|---|---|---|
| FLAME | Controls Flame brightness. |
5 Settings: (L1-L2-L3-L4-L5) Flame dims from L1 to L5. F5 is the brightest
setting.
FLAME – Log| | Controls Log Flame change.
3 colors: ( F1-F2-F3) Flame dims from F1 to F3.
HEATER| | Controls the Heater.
Press button to initiate the heater.
(OFF) no heater or blower.
(LO), heater blows warm air (750W)
(HI), heater blows hot air (1500W)
NOTE: Heater functions cycle from OFF-LO-HI
TIMER| | Controls the Timer.
9 Settings: (1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h,9h) Press button until reach
desired setting.
TEMPERATURE| | 1. Press once: Touch panel indicator becomes active.
2. Press again until desired setting is reached. Digital display shows
setting circles as below. NOTE: Press the button for 10 seconds, the
temperature setting will switch from °C to °F. Same way from °F to °C.
WARNING: Do not move or remove the mesh trim panel, when the appliance is
plugged in and operating.
This will cause the remote control and touch panel to no longer function
NOTICE
When the heater is first turned on, a slight odor may be present. This is
normal and should not occur again unless the heater is not used for a long
period of time.
NOTICE
To improve operation, aim the remote control at the front of the fireplace. DO
NOT press the buttons too quickly. Give the unit time to respond to each
command.
Remote Control Battery Information
- This remote control uses two AAA batteries.
- Instructions for battery installation are on the Remote Control battery compartment.
** NEVER dispose of batteries in fire. Failure to observe this precaution
may result in an explosion. Dispose of batteries at your local hazardous
material processing center.
Temperature Limiting Control
** This heater is equipped with a Temperature Limiting Control. Should the
heater reach an unsafe temperature, the heater will automatically turn OFF. To
reset:
- Unplug the power cord from the outlet.
- Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
- Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are, use a vacuum to clean the vent areas.
- With the POWER switch in the OFF position, plug the power cord back into the outlet.
- If the problem continues, have your outlet and wiring inspected by a professional.
Care and Maintenance
Cleaning
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so
could result in electric shock, fire, or personal injury.
NEVER immerse in water or spray with water. Doing so could result in electric
shock, fire, or personal injury.
Metal:
- Buff using a soft cloth, slightly dampened with a citrus oil-based product.
- DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Glass:
- Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper towel or lint-free cloth.
- NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Vents:
- Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Plastic:
- Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
- NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Thank you for purchasing this product!
If you have questions about assembly or operation of this product, or missing
parts, or if the product is damaged, please e-mail us at:
DO NOT RETURN
Contact our customer service team for help first.
velay@velayhome.com
Tel: 1-302-887-0290
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>