TARAMPS THS 3600 Multi Channel Receiver Instruction Manual

THS 3600
Multi-Channel Receiver
2 x 60W RMS

The installation of this product must be made by a qualified professional.

Introduction

Congratulations on purchasing a Taramps product.
Developed in a modern laboratory, with highest technology and highly qualified professionals.
This manual explains all the resources, operations and guidelines for resolving questions that may arise in your installation. Take a time to read it carefully and ensure the proper installation and use of all the benefits that this product can offer.
In case of doubt even after reading this manual, please contact our technical support at the number +55 18 3266 4050 or our website www.taramps.com.br.

Presentation

Application examples:
The TARAMPS THS 3600 is a Multi Channel Receiver developed with high technology to integrate different environments. Compact and powerful it can be used in several applications providing quality sound.
– Environment sound for stores, shops and clinics. It also allows, through the microphone input, that warnings are transmitted via the sound system.
– In your leisure area, gourmet space, country house, etc. Including various audio input options, such as Bluetooth, AUX and USB, it allows the audio sources to be easily changed giving the user exibility in choosing the preferred audio.
The equipment is automatic bivolt and can be connected to any power plug between 90 and 240V. It has a switching power supply that is more efficient in the consumption of electricity.
If you are not going to use the product for a long time, we recommend that you disconnect from the power outlet.

Important recommendations

-The THS 3600 must be installed in a stable and ventilated place, away from heat and humidity.
Avoid locations with direct sunlight.
– Do not block the ventilation holes on the top and rear.
– Carefully observe the polarity and impedance of the loudspeakers.
– Avoid falls and impacts.
– Use cables according to the distance between the THS 3600 and the loudspeakers.
The table below shows the recommended gauges according to the distances:

– In case of unwanted noise make sure that the cables and connections are in good condition.
Leave the volume to a minimum of unused channels.

Audio source

1. USB: Flash drive input *
   The TARAMPS THS 3600 has the following audio inputs:

2. MICRO SD CARD *

3. AUX (front): P2 standard auxiliary input.

4. AUX1 and AUX2: RCA standard auxiliary inputs.

5. BLUETOOTH

6. FM radio

7. Microphone input (standard P10)

• The connected device must contain music in MP3 format to be identied by the equipment. Maximum supported size: 64GB.
  We advise you to always have a good antivirus, so there are no problems with the Flash Drive or micro SD card when connecting to the product. Infected devices may cause  undesirable effects to the THS 3600, such as: Slow music reading and general failures.
  Do not use the USB input to connect to the computer or to recharge other devices that have batteries.

Package content

• 01 Multi Channel Receiver THS 3600
• 01 Remote Control

Knowing your equipment

Front Panel

1. MICRO SD: Micro SD memory card input. (The card must be positioned as the image shows, with the terminals facing up

2.  USB: Input to Flash Drive.

3. Aux. (Connector P2): Receives audio signal from the P2 output of your phone, tablet, MP3, computer, among others. Use good quality cable to avoid unwanted noise.

4.  Short Touch (Track-): Rewind the music tracks in the USB/SD/BLUETOOTH.
   Long Touch (Volume -): Reduce the volume in all sources options.
   FM: Short Touch: Reduce 0.1MHz of the frequency.
   Long: Automatic search to previous stations.

5. Short Touch (Play / Pause): Pause or start the music to USB / SD / BLUETOOTH.
   Short Touch: Mute to AUXILIARY option
   FM: Short Touch: Advances next saved memory position of FM stations.
   Long: Searches for FM stations and saves them in memory.

6. Short Touch: (Track+): Forward the music tracks in the USB/SD/ BLUETOOTH.
   Long Touch:(Volume +): Increase the volume in all sources options
   FM: Short Touch: Increase 0.1MHz of the frequency. Long: Automatic search to next stations.

7. Short Touch (MODE): Changes the source options, such as: USB / SD / AUXILIAR / BLUETOOTH / FM.
   Long Touch – To turn off the device. (The device will stay in stand by mode)
   Turning the device off via this button does not disconnect the microphone input from it and the ON LED on the front panel will remain on. To switch the device off completely, use the ON / OFF switch on the front panel.

8. LED Display – Remote control IR sensor: For better communication between the remote control and the device, point the control at this point on the display.

9. AUX1 / OPTICAL or AUX 2 KEY: Button pressed: Selects AUX1 and Optical inputs.
   Button not pressed: Selects the AUX 2 input. (Inputs on the rear panel).

10. ATT: LED audio attenuation indicator. When identifying an audio signal from the microphone input or emitting the ding-dong signal (GONGO), the equipment attenuates the output signal, allowing higher evidence of the microphone. After 2 seconds without using the microphone, it returns to the state without attenuation.
    It is possible to enable or disable this function. With the device in standby mode, press and hold the gong key for 5 seconds. The ATT LED will flash 3x with the function enabled or 1x with the function disabled.

11. VOL MASTER: Controls the global volume level and must be used to adjust the output power desirable.

12. MIC: P10 input for microphone.
    Microphone Recommendations:
    – The microphone signal has a low amplitude, so improper use can cause unwanted noise.
    – Use quality cables and connectors.
    – Do not wrap the microphone cables.
    – Do not pass the microphone in front of the loudspeakers. This causes feedback.

13. VOL MIC: Adjusting the volume of the microphone and the GONGO (ding-dong). If you do not use the microphone and GONGO, it is recommended to keep the volume to a minimum.

14. GONGO: GONGO activation key.
    The product has 3 GONGO options. To select another option with the device on, press and hold the “GONGO” key. The 3 gong patterns will be emitted in sequence (do not release the key). To select an option, release the “GONGO” key after hearing the  desired option.

15. EQUALIZATION: Ways equalization adjustment
    LOW: Bass frequencies
    MID: Middle frequencies
    HIGH: High frequencies.

16. VOL CH L / VOL CH R: Adjust each channel level (L ou R).

17. LED ON: Indicates that the product is turned on.

18. TECLA ON/OFF: Main ON/OFF switch.

Protection System

The THS 3600 has a protection system against outputs overload and outputs short circuit.
When the protections are activated, the ON LED on the front panel turns on temporarily and the audio output is interrupted. About 2 seconds, or the audio is restored.
If the protection system or system meets frequently, review the settings and installation of your system. Rear Panel

1. POWER CABLE: Plugged it into a powered outlet. This product operates from 90V AC to 240V AC 50Hz/60Hz..

2. VENTILATION HOLES: Do not obstruct the rear ventilation and the upper ventilation (cover) for the product to perform better.

3. SPEAKER OUT: To connect the loudspeakers. Follow the indicated polarity and the recommended minimum impedance of 4 ohms for each channel.

4. LINE OUT: The LINE OUT output allows to send the audio signal (not amplified) to other equipment, such as another THS 3600, an amplifier or active subwoofer.
   The LINE OUT sound is affected by the 3 Band Equalizer and Volume controls. (LOW, MID, HIGH and VOLUME controllers)

5. INPUT AUX 1, OPTICAL e AUX 2: Audio inputs. Use the frontal key to select.

6. FM ANTENNA: Indoor wire antenna for FM radio reception. Position the wire antenna in order to achieve the best FM reception.

Remote Control Function

THS 3600 has a compact remote control, so you can remotely control the device with practicality.

| ON / OFF: Press the key to turn off:
USB / BLUETOOTH / SD / AUXILIAR / FM.
Turning the device off via this button does not disconnect the microphone input from it and the ON LED on the front panel will remain on. To switch the device off completely, use the ON / OFF switch on the panel.
---|---
| MODE: Switch the audio source (USB, BLUETOOTH, SD, AUXILIARY, FM).
| MUTE
| PLAY / PAUSE: Pause or start the music to  USB / SD / BLUETOOTH.
FM: Short Press: Advances next saved memory location of FM stations.
Long Press: Searches for FM stations and saves them in memory.
| TRACK –  Previous  track (short press)
FOLDER  –  Previous folder (long press)
FM: Short Press: Previous 0.1MHz of the frequency.
Long Press: Automatic search to the previous station.
| TRACK + Next track (short press)
FOLDER + Next folder (long press)
FM: Short Press: Next 0.1MHz of the frequency.
Long Press: Automatic search to the next station.
| EQUALIZATION: Pop / Rock / Jazz / Country / Normal.
Do not work in auxiliary mode.
FM: Short Press Return to the saved memory position of FM stations.
| VOL-: Volume down
| VOL+: Volume up
| REPEAT: Repeat /play MP3 options
| U/SD: Switch mode between USB / SD Card
FM: Searches for FM stations and saves them in memory.

NUMERIC KEYBOARD: FM: Long Press saves FM stations.

Bluetooth

When selecting the Bluetooth function (identied with “bt” on the display), the THS 3600 waits for a Bluetooth connection. Search for the device called “TARAMPS THS 3600” using your phone, tablet, PC or other and match it.
– To connect to a new device, disconnect the current one and make the new Bluetooth pairing.
Bluetooth specication: class II with a 10m maximum range and may vary according to the environment (such as walls) and the connected device.For other devices the connection system is similar (consult manufacturer’s manual)

Bluetooth examples of use

Some TVs have an audio output system via Bluetooh. If your TV has this feature, it’s possible to transmit the audio to the THS 3600.
Consult your TV manufacturer’s manual.
Example of using P2 Connector
Select the AUX mode on the ‘MODE’ key.
Example of using RCA input
Select the AUX mode on the ‘‘MODE’’ key and the AUX 2 key not pressed. Connection examples – Wall sconces
Examples to until 16 loudspeakers 8 ohms eachFor this kind of connection use cables with a minimum gauge of 1.5mm² for up to 40 meters. For long distances, consult the table on page 12 ‘‘ Important recommendations ’’. It’s necessary to make connections in parallel and series as shown in the example, to match impedance.

Term of warranty

Located at Rua Abílio Daguano, 274 Res. Manoel Martins – Alfredo Marcondes – SP, ZIP CODE 19.180-000, TARAMPS guarantees this product against defects in design, manufacture, assembly and / or jointly due to design flaws that make it inappropriate or unsuitable for the intended use, for a period of 12 months from the date of acquisition.
In case of a defect in the warranty period, TARAMPS is responsible for the repair or replacement of the device manufactured by it.
This warranty excludes:

• Products damaged by improper installation, water infiltration, violation by unauthorized persons;
• Torn or torn warranty seal;
• Cases where the product is not used under normal conditions;
• Defects caused by accessories, modifications or equipment attached to the product;
• The product shows damage due to falls, impacts or the action of agents of nature (floods, lightning, etc.);
• Costs of removing and reinstalling the equipment, as well as transporting it to the technical assistance station;
• Damage of any nature, resulting from product problems, as well as losses caused by interruption of use.

Technical assistance

We have technical assistance all over Brazil and we are always ready to answer your questions and needs.
To locate an electronic Taramps technical assistance near you, access our website: www.taramps.com.br/pt/rede-de-assistencias- tecnicas or contact the factory’s technical assistance department:
Taramps Eletronics
Rua Abílio Daguano, n 274
Phones + 55 18 3266-4050 / +55 18 99749-3391
ZIPCODE: 19.180-000
E-mail: service@taramps.com.br

Technical features

TARAMPS THS 3600:____Receiver Multi Channel Class D
Number of Channels: 02
RMS Power:____120W (60W + 60W) ABNT NBR IEC 60268-3*
Nominal RMS Power of each channel:__60W (1% THD+N)
RMS output voltage for each channel:15,5Vrms (1% THD+N)
Total Harmonic Distortion + Noise (THD + N) at the
nominal power of each channel (60W)____ <1%
Each channel nominal Impedance:____4 Ohms
MIC Sensitivity:____10mV
AUX input Sensitivity:__ 200mV
MIC input impedance:__2,2K Ohm
AUX input impedance:__ 2,2K Ohm
Frequency response (equalizers at 0dB):____ 15Hz ~ 20KHz (-3db)
Typical 3-way equalizer performance: :
Low (bass):__±12dB – 80Hz
Mid (mid bass):____±12dB – 2KHz
High (high):__±12dB – 10KHz
Power supply:___ 90 ~ 240V AC (automatic) – 50/60hz
Maximum consumption:____240W
Consumption in Stand by:_ 0W
Internal protection fuse:____3A
Protection System:Output protection against short- circuit and low impedance**
Ratio signal/noise:>70db
FM frequencies:___87.5 MHz ~ 108MHz
Dimensions:__ 386 x 59 x 142mm (15.20″ x 2.32″ x 5.59″)
Weight:__1.45Kg ( 3.15lb)

• Nominal power with 1KHz sinusoidal signal and 4 ohms resistive load. (Measured according to ABNT NBR IEC 60268-3 sound equipment, Part 3: Amplifiers).
  ** Protection system on page 15.
  For more information or questions visit our website or contact TARAMPS support.
  The values mentioned are typical and may change due to the tolerance of components or the manufacturing process.
  Taramps reserves the right to modify the contents of this manual without prior notice and not to apply the modications to units previously produced.

+55 18 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. Joao Silvério, 121 » Res. Manoel Martins
Alfredo Marcondes – SP
Industria Brasileira – Made in Brazil
www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>