White Elephant Gifts 12124 Smart Bird Feeder with Camera User Manual

White Elephant Gifts 12124 Smart Bird Feeder with Camera

FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of t he FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located for operating in conjunction with any other antenna or transmitter. FCC (USA) 15.9 prohibition against eavesdropping except for the operations of law enforcement officers conducted under lawful authority, no person shall use, either directly or indirectly, a device operated pursuant to the provision of this part for the purpose of overhearing or recording the private conversations of other unless such use is authorized by all of the parties engaging in the conversation.

Contents

• Bird Seed Container*1 (Camera and Bird Seed Outlet Valve include

• Feeder Cover *1

• Bird Perch*1

• Mounting Bracket*1

• Bracket Screws *2

• Bracket Screw drive*1

• 3WSolarPane1*1

• Solar Bracket Screws3
  Solar Panel Kit1

• Manual’!

• Drilling Template Sticker1
  Solar Bracket Positioning Sticker1

• Bracket Screws*4

• Anchors*4

• Thumb Screws·*3

• Type -C Power Cable*1

• External Antenna*1

• Strap* 1

• Fruit Holder*4

• Ejector Pin*1

Product Diagram

How to Assemble Smart Bird Feeder

Assemble the base
Step 1. Insert the antenna into the hole in the middle of the back of the bird seed container and twist it tight.
Note: If the antenna is disconnected or not attached properly, the app will not be able to connect to the smart bird feeder .

Assemble Feeder Cover

Step 1. Align the feeder cover with the roof of the bird seed container and gently put it down, then fasten the buckle on the right side of the cover to the bird seed container. You will hear a clicking sound which indicates that the cover is securely mounted.

Assemble the Bird Perch
Step 1. Install the bird perch at the front of the base.

Step 2. Use one of the provided thumb screws to secure the bird perch

Insert Micro SD Card into Camera
Note: The SD card is not included, and it is not necessary. You can use the feeder without it.
Smart bird feeder camera comes with a built-in card slot that supports up to 128GB Micro SD card. Insert the card into the camera before you assemble the whole unit.
Step 1: Gently rotate the camera down to the bottom.
Step 2: Open the top silicone plug. Insert the Micro SD card. Make sure to insert it in the right direction. Step 3: Finally, cover the silicone plug.

How to Set up the Camera

How To Turn On & Off The Camera

Note: The reboot hole is used to restart the camera without changing the settings. You can insert the included ejector pin into the reboot hole, then press and hold to reboot.

Indicator Light Status

Camera Specifications

• Download and Install the VicoHome App 4.1. Scan the QR code below or searcH’ VicoHomE!’ on APP Store or Google Play Store to download and install the app. 4.2. Open the link to download and install  the App: https://www.vicohome.io/download/

Sign up
Note: The most up-to-date information can be found through the APP.

• Open the app and input your username, country, email address. Check and agree to the User Agreement, then click ‘Next Step’. (For a better experience, allow all permissions to avoid missing any notifications.)

• You will get an email with a verification code for account confirmation. Enter the code and click ‘Next Step’.

• Set the login password and reenter it to confirm. Click ‘Next Step’ . (For account safety, the password needs to be a combination of at least 8 characters of uppercase and lowercase letters.)

Add the Camera

Note: The most up-to-date information can be found through the app.

• Click “Add a new device now”on the VicoHome App.

• Follow the instructions on the app to turn on the camera: Long press the power button of the camera for 3s to turn on the camera. Then the indicator light in the front of the camera will be solid blue. Double click the power button to enter network configuration mode after the prompt tone.

• Listen for the ‘ding dong ding dong’ sound. After hearing the sound, click ‘I heard the sound or saw the light on’ in the app. Then, click ‘Next Step’.

• For quick connection, please follow the instructions to open the Bluetooth settings.

• At this point, the phone enters the state of searching for smart bird feeder.

• After hearing ‘ding dong ding dong’, check ‘I heard the beeping sound’ and click ‘Next Step’.

• Select the smart bird feeder you need to connect.

• Enter the WiFi name and WiFi password you want to connect to, check ‘Remember the Wi-Fi name and password after successful connection’, and click ‘Next Step’.

Note: The smart bird feeder only supports 2.4 GHz Wi-Fi networks with strong wall penetration capability.

• Confirm the Wi•Fi name and password.

• Click ‘Connect’ .

Note: If the smart bird feeder cannot be located by Bluetooth, a QR code will appear. Point the QR code at the lens of the camera to connect.

• When connecting, please wait patiently for 15 seconds, then you will hear a sound ‘Wi-Fi Connected’.

• Set a name and location for smart bird feeder .

• Finally, you will be informed of the current Wi-Fi network status. When the signal is weak, adjust the router or bird feeder position.

• When you finish connecting, a message will appear about getting free cloud storage for 30 days. After 30 days, you can subscribe to a cloud storage package that suits you.

Possible problems with connecting

• When you hear ‘Wi-Fi Password Error’, please check whether the Wi-Fi password you entered in the app is correct.
• When you hear ‘Authentication error’, please ensure that your Wi-Fi network is not an enterprise-level Network. The device supports only networks with security below WPA-2.
• When you hear ‘Wi-Fi not found’, please check that you selected the correct Wi-Fi name. Place the device near the Wi-Fi router and ensure that the router is powered on. Please note that SGhz Wi-Fi cannot be located by the device.
• When you hear ‘Retrieving IP timeout’, it indicaes that the number of devices connected to the router has reached the maximum. Please remove some of the connected devices that are not commonly used or restart the router to clear the unconnected devices. You may even need to contact the router administrator.
• If you hear ‘Cloud service connection fail’, it could be caused by network disconnection. Please ensure that the network connection is normal and try to temporarily turn off the firewall.

Share the camera

You can use this feature when you need to use the camera with other family members or friends. Only the admin user who has bound the camera for the first time can share and set up the camera, while other members can only view the live video or video playback feature of the camera.

• Forthe admin user of the camera, find the camera you wish to share on the app homepage or camera settings screen, then click the share button and enter the share page. Click “Device Sharing” to generate a shared QR code .

• For users who need to be shared with, click”+” on the homepage and select “Add Friend’s Device” to enter the scan code page.

• After the shared user successfully scans the QR code on the adm1h user’s mobile phone, the ad min user will receive a confirmation notification, then click “Accept” to complete the camera sharing.

How to delete the shared smart bird feeder
If you want to delete shared friend devices, please go to the sharing page and select the friend account you want to delete. Swipe left and click the delete button.

How to Charge the smart bird feeder

Check Battery Level
After setting up the camera, please check the battery level of the camera to make sure it is fully charged before installing it in the yard. The app will also remind you to charge your smart bird feeder when the battery is low

Charge the smart bird feeder
There are two ways to charge it.

• Indoor Charging:
  If you need to charge after installation, please don’t move the camera and the base, just remove the birdseed container.The charging port is in the middle of the back side of the bird seed container. Please use the Type-C cable to plug into the SV/1.SA charging adapter to charge the smart bird feeder.

Outdoor charging:
You can directly use the equipped solar panel to connect to the charging port in the middle of the back side of the bird seed container.
Note: During charging, the camera’s indicator light is solid yellow, and when the camera is fully charged, the indicator light will turn solid green. It will take ten hours to fully charge the camera.

Installation

Before Installation

• Keep Smart bird feeder and all accessories out of reach of children and pets.
• Make sure the camera has been fully charged (DCSV / l.SA).
• Working temperature: -1o•c to 45°C (14°F to 113°F)
• Working relative humidity: 0-95%
• Please do not expose the camera lens to direct sunlight.
• The camera has an I P65 waterproofing, which supports working properly under rains or snows. But it can not be soaked in water.

Note:

• Smart bird feeder only works with 2.4 Ghz Wi-Fi.
• Strong lights may interfere with the device’s ability to scan QR codes.
• Avoid placing the device behind furniture or near microwaves products. Try to keep it within range of your Wi-Fi signal.
• Please check the signal of the camera again before installing it on the shelf to ensure that the signal is good enough. Avoid removing the camera after installation due to weak signal.

During Installation
Note: Before you drill holes in your wall, check that the smart bird feeder has been successfully added to your VicoHome App and is able to stream video.

• Find a Position with good Signal

Please install the smart bird feeder in a position where its view is not blocked and ensure that it is within range of the Wi-Fi network. Check if the WI Fl signal strength in the yard is enough (you can check the WIFI signal strength through the app). When the smart bird feeder is added to the app, the signal strength of the smart bird feeder will be displayed (click the settings on the right side of the smart bird feeder on the home page to check the signal strength.) When the signal strength is Strong, the position is good for installing the bird feeder.

Note: It is generally not recommended to have more than two walls between bird feeders and routers.
When the signal strength is Medium, it is necessary to check that the real- time video works smoothly and continuously.

When the signal strength is Weak, do not install the bird feeder in this position.

Wall Installation:
Step 1:

1. First mark the location of the holes on the wall by using the included drilling template stickers. Then use a 5/16″/Smm drill bit to drill two holes.
2. Install two anchors to fix the bracker screws.
3. Install the mounting bracket on your wall with the two bracket screws provided.

Step 2:
Attach the base to the mounting bracket (there are silicone gaskets attached to the mounting bracket to prevent wear of the mounting bracket and base.)

Step 3:
Screw in the bottom of the interface between1 the bird seed container and the mounting bracket.

Note: Once installed, you can rotate the smart bird feeder based on the background, field of view, and light intensity to get the best angle; the mounting bracket and base should be securely fastened together so they don’t wobble when birds fly away or the wind blows.

Tree Installation:
Step 1:
Wrap the mounting bracket around the tree with a strap.

Step 2:
Attach the smart bird feeder bottom to the mounting bracket.

Step 3:
Screw in the bottom of the interface between the bird seed container and the mounting bracket.

Note: Once installed, you can rotate the smart bird feeder based on the background, field of view, and light intensity to get the best angle; the mounting bracket and base should be securely fastened together so they don’t wobble when birds fly away or the wind blows.

Stand Installation:
Step 1:
The smart bird feeder can be placed steadily on a flat surface, but for stability, we recommend that the backplane is installed and fixed on a flat surface. Use the provided drilling template sticker to mark the position of holes on a flat surface. Use a 5/16″/Smm drill bit to drill two holes.

Step 2:
Install two anchors to fix the bracket screws.

Step 3:
Install the feeder bracket on your wall with the two bracket screws provided.

Step 4:
Attach the base to the mounting bracket (there are silicone gaskets attached to the mounting bracket to prevent wear of the mounting bracket and base.)

Step 5:
Screw in the bottom of the interface between the bird seed container and the mounting bracket.

Note: Once installed, you can rotate the smart bird feeder based on the background, field of view, and light intensity to get the best angle; the mounting bracket and base should be securely fastened together so they don’t wobble when birds fly away or the wind blows.

Pole installation
Note: You can also install the mounting bracket to the pole first (refer to the next step).

Step 1:
Attach the smart bird feeder bottom to the mounting bracket.

Step 2:
First insert the pole into the ground, then place the bird feeder on the pole, and finally tighten the screws.
Note: It fits any standard-sized birdhouse pole, with al”/ 2.5cm diameter. Please note that the pole itself is not included in the package.

Note: Once installed, you can rotate the smart bird feeder based on the background, field of view, and light intensity to get the best angle; the mounting bracket and base should be securely fastened together so they don’t wobble when birds fly away or the wind blows.

Use the fruit holder
The smart bird feeder comes with4 fruit holders that are designed for birds. You can fasten oranges, apples, or other types of fruit on it to attract more birds.

Step 1: Screw the fruit holder onto the bird perch, it needs to be tightened so that it wi II not fa II.
Step 2: Fasten fruit onto the fruit holder.

Install solar panel
Step 1:
Please select a position with the most sunlight throughout the year for your solar panel. The solar panel only needs a few hours to direct sunlight to sufficiently power your camera daily. The amount of energy that the solar panel can produce is affected by the weather conditions, seasonal changes, geographic locations, etc.

Step 2:

• When installed on a wall/tree
  Use the drilling toot to punch holes in the wall or tree according to the hole distance of the base. It is recommended to mark the holes on the wall or tree before drilling with the drilling template sticker. Screw the anchors into the holes, and then connect the solar panel bracket to the anchors with screws.
  ( The anchors and screws used here are all in the Solar Panel Kit)

• When installed with a pole in a yard
  Connect the solar panel bracket to the Bird cage bracket with screws.

Step 3:
Slot the solar panel into the bracket and make sure it’s secure.

Step 4:
loosen the adjusting control on the bracket and adjust the angle of the solar panel to make it receive direct sunlight, and then re-tighten the adjusting control to secure your setting.

Step S:
Connect the solar panels to the charging port of the bird feeder with the equipped 3-meter Type-C charging cable.

How to Add Bird Seed
Step 1:
Open the catch on the left side of the bird seed container and gently lift the feeder cover upwards.

Step2:
There is a bird seed outlet valve placed in the seed outlet of the bird seed container, please take it out after loading the seeds, and put it inside the feeder cover (like the position shown in the picture, you can also move the seed outlet valve after installing the smart bird feeder in the yard to prevent the seed from leaking out during installation).

Step3:
Finally, close the feeder cover.

Cleaning and Maintenance

Smart bird feeder is designed with the safety and comfort of our feathered friends in mind and is incredibly easy to clean. Cleaning your feeder is the most effective and most important step towards preventing the spread of avian diseases. We recommend cleaning the feeder once a week with a brush and a mild disinfectant.

1. Cleaning the smart bird feeder len: Add a drop or two of lens cleaning fluid or rubbing alcohol to a microfiber cloth or a cleaning wipe, then wipe the lens gently to remove fingerprints, oil, smudges, dirt, and dust.
2. Cleaning the base: After removing the bird seed container, wash it directly with water, you can use a soft brush to clean away the extra seeds and dirt.
3. Cleaning the inside ofthe bird seed container: Fill a silicone measuring cup with water and pour clean water from the bird seed inlet on the top.Let the water flow out naturally and let it dry.
4. Other: If the feeder cover, bird perch, mounting bracket, solar panel, and other parts of the bird seed container get dirty, rinse them gently with water and wipe them with a clean cloth.

How to Do Bird Al Recognition

1. Click ‘User’ in the lower right corner of the app, and then click ‘VicoHome Awareness Plus’ to get ‘VicoHome Awareness Plus 30- day free trial’, You will receive one month of free premium membership and access to the ‘Bird Fans Plan’, then you will be able to identify 10, 000+ birds with the bird fans plan.
   Note: The most up-to-date information can be found through the app. Monthly subscription is required after the 30-day free trail.

2. When the camera detects a bird, it will notify you that a bird has been detected.

3. Click on ‘A bird detected’ to identify the bird breed.

FAQ

How should I solve problem when using the app?

When the app fails, it may be a internet connection problem. You can try restarting the app or internet connection. If the problem with app still exists, please contact us via the VicoHome app.

How can I identify birds?

The smart bird feeder will start shooting when the bird arrives, and then you can watch the video through the mobile app, and the information in the video will prompt you to identify what kind of bird it is.

Will the camera show red lights when night vision is activated?

The built-in infrared lamp beads make the camera only show some dim red lights when night vision is activated, but the image quality is still clear in a low- light environment.

Can I use the bird feeder without an SD card?

The smart bird feeder can work normally without an SD card, and the captured videos will be stored in the cloud. Different cloud packages have different storage time and storage capacity.

Will I have to pay a monthly subscription to use the app?

We provide free 3-day cloud storage, if you need a more advanced storage package, you can check the package price in the Vi co home Awareness Plus in the app

What is the maximum length of recording time?

If you set the duration as Auto, when something appears in the view of the camera, it will start recording a video for up to 3 minutes with monthly subscription.

How can I quickly view videos by category?

Click the icon in the upper left corner of the Library page to start filtering videos by category. Select the category you want to see and then click Save to view the video playbacks.

How can I prevent seeds from getting wet when it rains?

The smart bird feeder is equipped with a silicone cover for the bird seed outlet, which can keep the bird seed from excessive moisture when it rains.

Does the camera support 5.0 Ghz Wi-Fi?

No, currently only 2.4 GHz Wi-Fi is supported.

Can the camera be used without Wi-Fi?

No, the camera must be connected to WiFi when the app is set up. If you want to use smart bird feeder in a place with­out Wi-Fi, you can use the hotspot of your mobile phone first, let smart bird feeder connect to it, and then take it outdoors or in the wild. Bird Al recognition doesn't work without the Internet.

Can the app check the signal strength of the camera?

You can check the signal strength through the app. When the camera is added to the app, the signal strength of the camera will be displayed (click the settings on the right side of the camera on the Home Page to check the signal strength.) When the signal strength is Strong, this position is good for installing the bird feeder. When the signal strength is Medium, it is necessary to check whether the real-time video works smoothly. When the signal strength is Weak, do not install it in this position.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>