RECESS Standup Desk User Guide
- June 17, 2024
- RECESS
Table of Contents
RECESS Standup Desk
Product Information
Specifications
- Beam x 1
- Table Top x 1
- Feet x 2
- Bracket x 2
- Control Pad x 1
- Legs x 2
- Power Box with Cable x 1
- Rubber Pad x 10
- Cable Clips x 5
- Allen Key x 1
- 12mm Bolts x 12
- 14mm Bolts x 8
- 19mm Screws (Thick) x 12
- 19mm Screws (Skinny) x 2
Product Usage Instructions
Step 1: Adjusting Beam Width
Use the Allen Key to adjust the beam width by aligning the holes in the beam with the pilot holes in the Table Top.
Step 2: Attaching Legs
Insert the Legs into the Beam, align the holes, and secure each leg with four 12mm Bolts.
Step 3: Attaching Feet
Place the Feet on the base of the Legs and secure them using four 14mm Bolts per leg.
Step 4: Attaching Brackets and Rubber Pads
Secure the Brackets to the Beam using two 12mm Bolts per bracket. Insert Rubber Pads for cushioning.
Step 5: Attaching Table Top
Align the frame with the Table Top’s pilot holes and secure them using Thick 19mm Screws. Secure the Power Box and Control Pad using specified screws.
Step 6: Wiring
Connect wires from the Control Pad and Legs to the Power Box. Connect the power cable to the Power Box.
FAQ
- Q: Can I assemble the desk alone?
- A : Yes, assembly can be done alone, but having a friend to help with certain steps can make it easier.
- Q: Can I adjust the height of the desk?
- A : Yes, this standup desk allows you to adjust the height for your comfort.
- Q: Is the desk easy to move once assembled?
- A : The desk is designed to be sturdy but can be moved with caution when needed.
Congrats
You are now the proud owner of your very own Recess Standing Desk. Now let’s get cracking with assembly- it shouldn’t take you much longer than 30mins!
In the Box
Tools Required
1. Use the Allen Key to loosen the 10mm Bolts (x8) that are pre-installed in the Beam. Now, set your beam width by laying it on the underside of the Table Top and lining up the two holes in the middle of the beam with the two pilot holes in the middle of the Table Top. Then,re-tighten the bolts.
TIP : Don’t fix the beam to the Table Top just yet – ease up tiger!
2. Next, place the Legs (x2) into the Beam, aligning the holes in the legs with the holes in the beam. Pull the wires from the legs through the openings in the beam, as shown in the diagram below. Tightly secure each leg to the beam with four12mm Bolts (4 bolts per leg).
TIP : Both legs work on either side of the beam – stress less!
3. Now take the Feet (x2) and place each foot on the base of the Legs, ensuring the holes are aligned. Tightly secure the feet to the legs using four14mm Bolts (4 bolts per leg).
TIP : Either foot works with either leg – your desk is ambidextrous.
4. A- Carefully flip the desk frame so it is now standing upright. Take the Brackets (x2) and align the two middle holes with the holes of the Beam. Tightly secure each bracket with two12mm Bolts (x4) (2 bolts per bracket)
B – Next, push the Rubber Pads (x10) through the 8 holes on the bracket (4per bracket) and the two middle holes on the beam (see diagram below) – these ensure a nice comfy cushion foryour Table Top.
TIP : If you’ve got a mate nearby, best to give them a shout for a helping hand for this step – many hands make light work!
5. A- With your mate, flip the assembled frame on top of the underside of your Table Top. Align the frame with the Table Top’s pilot holes and use the Thick 19 mm Screws (x10) to secure the frame to the Table top- the pilot holes should line up with the same holes you inserted those pads into on the frame.
B – Next, secure the Power Box between the Beam and wire grommet by inserting the Thick 19mm Screws (x2) into the pre-drilled holes in the Table Top. Then, line up the Control Pad holes with the pre-drilled holes in the Table top at the front (the beveled side) and secure the control pad in place using the Skinny
TIP : The Control Pad can go on whichever side pleases you most
6. Almost there – time to wire this bad boy up! Connect the wires coming from the Control Pad and two Legs, into the Power Box as shown in the diagram below. Then, connect the power cable to the power box
STOP : If you purchased the Cable Tray for cable management, at this point refer over to the assembly instructions for the Cable Tray here.
TIP : Use your Cable Clips (x5) to manage those nasty loose cables. Just stick them down where you see fit and loop those cables through.
7. Flip your desk with your chosen pal (last favour you ask of them we promise) and plug the power cable into the wall. If you’ve got a wonky floor, adjust the levellers on the feet as necessary.
TIP : Head to the pub for a bevvy – you’ve earned it!
All done!
Whether you’re shipping code for the next great Aussie startup, leverage tra- ding on crypto or just having a gander on the web, we hope your new Standup Desk keeps you working healthy and happy, giving you time for some Recess and play!
Now don’t be shy. Show us how it looks!
- @recess.au
-
myrecessoffice
Contact
Have a question, comment or suggestion?
User Guide
Memory Preset
To preset a specific heights), set your desk to the desired height. Once the height is appropriately set, press the ‘M’ button – the display should then show -‘ where the -‘is flashing. Then select the number you would like to associate with that height. Your handset will remember the exact height for each designated number even if power is lost.
Locking the Control Pad
Should you wish to lock your control pad, press and hold together the ‘M’ and’ ^ ‘buttons until the screen displays ‘Loc’. To unlock it, press and hold together the ‘M’ and ” buttons until the screen display returns to normal.
Anti-Collision Sensitivity y
To increase or decrease the sensitivity of the anti-collision feature, follow the below steps:
- Press and hold the ‘M’ button for 5 seconds.
- The screen should display ‘S-1’, where the 1 is flashing.
- Press the’ ^ ‘button so that the display now shows ‘S-2’, with 2 flashing.
- Press the ‘M’ button. From here, you can now adjust the sensitivity of the anti- collision feature, with 8 being the most sensitive and 1 the least.
- Once the desired sensitivity metric is selected, press the ‘M’ button to save your selection and return to the normal display.
Upper & Lower Limit
You can set an upper and lower height of the desk – the operation method is as follows
- Set the height to your preferred upper or lower limit. Note: when the height is below 98cm, a lower limit is being set. Above 98cm, and an upper limit is being set.
- Press the up and down buttons together for 5 seconds at the corresponding height. When you hear a beep sound, the upper or lower has now been set.
- To cancel the limit you’ve set, simply lower or raise the desk to the limit you set. Then press the up and down buttons together for 5 seconds – the same beep sound will occur and the limit has now been canceled.
Resetting the Motor & Control Pad
If you’re having issues with your control pad, try resetting it by following these steps:
- Lower the height of your desk down to the lowest height setting and release the down button.
- Press and hold the down button – do not release the button until you hear a beep sound.
- Your handset and motor is now reset and should be working as normal again.
Troubleshooting Guide
- Error Code E01
- a. Problem: Power box broken
- b. Solution: Contact Recess support to have new Power Box sent out
- Error Code E02
- a. Problem: Rod height difference between the legs is more than 1cm
- b. Solution: Re-assemble the frame and reset the motor (see above)
- Error Code E04
- a. Problem: Control Pad is broken
- b. Solution: Contact Recess support to have new Control Pad sent out
- Error Code E06
- a. Problem: Power box broken
- b. Solution: Contact Recess support to have new Power Box sent out
- Error Code HOT
- a. Problem: The motor is too hot. Time of operation has been more than 2 minutes within an 18-minute period.
- b. Solution: Let the motor rest for 18 minutes
- Error Code E18 & E26
- a. Problem: Lift capacity of 125kg has been exceeded
- b. Solution: Re-distribute the weight on your desk or remove some items.
If you’re having further issues, please reach out to the team by email hello@recess.com.au.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>